Studio Equipment charts

Notes: Reach Infinity

Let's dive into a Black Hole!

The Black Hole Symmetry is a Modulated Delay / Pitch shifted Reverb / Destruction Fuzz pedal.

Travel through the Ergosphere, the Event Horizon and the Singularity. The 3 parts of the pedal which can be played together or separetely.

Each pedal is designed, assembled, tested and numbered by hand in the Collision Devices workshop in France.

The B.H.S. has a lifetime warranty.

3 effects, one pedal

Singularity

Destruction Fuzz
The single setting "Disintegrate" allows you to raise your sound.
Forget the fact that your drummer plays loudly.
Settings :
Desintegrate : Volume setting with a huge fuzz.
Protect your ears please.

Event horizon
Pitch shifted Reverb
Long reverb based on the FV1 chip.
Harmonizes the reverb signal with a pitch shifter.

Settings:
Mix: Proportion of wet signal in the mix
Echo: Echo time (max 15s)
Radiancy: Proportion of pitch shifter in the echo signal
Pitch: Shifts the pitch of the note

Ergosphere
Modulated Delay
Based on the PT2399 chip to have a warm echo.
The echo signal is modulated by two oscillators.

Settings:
Mix: Proportion of wet signal in the mix
Time: Time between each repetition (From 0s to 1s)
Feedback: Number of repetitions
Modulation: Proportion of modulation in the delay signal
Speed: Speed of the main oscillator
Trimmer: Speed of the triangle oscillator

Specifications

Maximum current draw: 250 mA
Input Impedance: 1 MOhm
Size: 186 x 119 x 56mm

The use of an isolated power supply is recommended for powering all Collision devices Pedals.

Power supply not included.

The pedal is true bypass

Lifetime warranty

Voltage: +9V DC (negative center)
Output Impedance: 1 KOhm
Weight: 200 grams

Notes: Professional-standard 6-in/4-out interface from the trusted team at MOTU. Pristine sound courtesy of the high-end ESS Sabre32 Ultra DAC, with the versatility of MIDI in/out, dual headphone outputs and A/B monitor control.

Supplier's Notes:
Introducing the M6; Four mic inputs with best in class audio quality, speed, and metering

Audio Quality

Equipped with the same ESS Sabre32 Ultra DAC Technology found in audio interfaces costing thousands, the M6 delivers an astonishing 120 dB Dynamic Range on its main outputs. ESS converters also drive the headphone outputs, which rivals dedicated headphone amplifiers costing hundreds. Ultra-clean preamp circuits produce a measured -129 dBu EIN on the mic inputs. Capture and monitor your audio with pristine clarity.
ESS Sabre32 Ultra DAC Technology for superb analog sound

The same converter technology used in audio interfaces costing thousands

Measured 120 dB dynamic range on outputs

Measured -129 dBu EIN on mic inputs

ESS-driven headphone outputs

Speed

The M6 provides best-in-class speed for monitoring live inputs (mic, guitar or keyboard) through your computer, thanks to MOTU's expertly engineered USB drivers, which deliver class-leading, ultra-low 2.5 ms Round Trip Latency (at 96 kHz with a 32 sample buffer).

Metering

When recording and mixing, nothing is more critical than achieving optimum levels. The M6 is the only audio interface in its class with a full color LCD featuring clear, detailed level meters for all inputs and outputs. Enjoy professional-level volume control and feedback to get your sound just right.

Loopback

The M6 driver

provides convenient loopback channels to your host computer, so you can easily route computer output back to the computer, where you can mix it with up to four mics (and/or guitars) from the M6 in your host software for live streaming or podcasting. Streaming and podcasting has never been easier and better-sounding!

A/B Monitor Switch

The M6 is the only audio interface in its class to offer A/B monitor switching. Connect two pairs of monitors and quickly check your mixes on each pair with the push of a button.

Stand-alone operation

With the included multi-blade international DC power adapter connected, you can power the M6 when the computer is turned off (or completely disconnected from the M6). This allows you to monitor any live inputs you may have (mics, guitars, keyboards, etc.) without a host computer or iOS device needed.

A tradition of engineering excellence

Decades of award-winning product engineering for hit songs, mega tours, primetime shows and blockbuster movies goes into every MOTU audio interface.

Workstation software, virtual instruments and loops to get you making music right away

Connect the M6 to your Mac or PC and start laying down tracks with the included Performer Lite or Live Lite production software, plus hundreds of loops, one-shots and sounds from industry leaders Big Fish Audio, Lucidsamples and Loopmasters.

Technical Specifications

Sample rates: 44.1, 48, 88.2, 96, 176.4, 192 kHz
Mic/line/guitar: 4 x XLR/TRS "combo jack" mic/line/Hi-Z guitar inputs Independent preamp gain, 48V phantom power and monitor switch for each input
Analogue inputs: 2 x 1/4" line in
Analogue outputs: 4 x 1/4" TRS line out (balanced, DC coupled) 2 x 1/4" TRS stereo headphone with independent volume
Computer I/O: 1 x USB-C 2.0 audio class compliant Compatible with USB Type A host (*see power below) USB C-to-C and C-to-A cables included
MIDI I/O 1 x MIDI IN 1 x MIDI OUT 16 MIDI channels to/from computer host
Headphones: 2 x 1/4" TRS stereo headphone with independent volume 1 x 3-4 switch for optional monitoring of Line Out 3-4
Phantom power: 4 x individual +48V
Front panel: 2 x 1/4" TRS headphone output 1 x potentiometer - monitor vol 2 x potentiometer - phone vol 1 x potentiometer - input monitor mix 4 x potentiometer - mic/line/guitar input gain 11 x switches - (4) 48V, (5) MON, (1) A/B and (1) 3-4 160 x 120 pixel full-colored LCD with input and output level meters
Power: Bus-powered through USB* Optional multi-blade international 15V DC power adapter (included) *USB bus power available with USB-C hosts only. For other hosts, use the included DC power adapter. For iOS devices with a Lightning port, an Apple Lightning to USB3 Camera Adapter is required (sold separately).
Dimensions and weight (width x depth x height, enclosure only) 9.21 x 4.75 x 1.8 inches 23.4 x 12.0 x 4.57 cm 2.15 lbs / 0.975 kg


System Requirements

Mac System Requirements
Intel Core i3 Mac or faster (including Apple silicon Macs) 4 GB RAM; 8 GB or more recommended macOS version 10.11 or later (Optional driver requires 10.13 or later) Available USB port A large hard drive (at least 500 GB for recording)

Windows System Requirements:
1 GHz Pentium-based PC compatible or faster 2 GB RAM; 4 GB or more recommended Windows 10 or later (x64 only) Available USB port A large hard drive (at least 500 GB for recording)

Class-Compliant Support:
USB audio class compliant for plug-and-play operation on Mac or iOS (no driver required)

Included Software:
MOTU Performer Lite Ableton Live Lite 11 6 GB of loops and sounds from Big Fish Audio, LucidSamples, Loopmasters and MOTU

Line output:

Connector type: 1/4" TRS, balanced, tip hot, Dynamic range (A-weighted): 120 dB, THD+N (unweighted): -110 dB, Max level: +16 dBu

Line Input:
Connector type: 1/4" TRS, bal/unbal, tip hot, Dynamic range (A-weighted): 115 dB, THD+N (unweighted): -110 dB, Max level: +16 dBu

Mic input:
Connector type: XLR, balanced, pin 2 hot, Dynamic range (A-weighted): 115 dB, THD+N (unweighted): 129 dBu EIN, Max level: +10 dBu (at minimum gain)

Phones
Connector type: 1/4", TRS stereo, Dynamic range (A-weighted): 115 dB, THD+N (unweighted): -110 dB, Max level: +12.5 dBu

Notes: Beautiful combo of vintage tech and modern features from Benidub's boutique analogue phaser unit. Six-stage stereo processing with real-time switching to 12-stage mono mode. Excellent playability with large controls.

Supplier's Notes:
Old school mojo with a modern twist on versatility and sound quality
PHASE is an analogue optical phaser, featuring 12-stage in mono and 6-stage when used in stereo. You can switch between the two modes with the "Mode Select" control any time. We made it completely clickless, allowing you to flawlessly switch mode during your set! This unique control provides even more playability and a wide range of phaser tones.

100% analogue audio path for subtle-to-extreme true phasing colours and tones

Unlike many other phasers in the market, designed after guitar-frequencies needs, Benidub's PHASE has been built with a "studio" oriented design in mind, making it the best phaser for either producers and musician. From studio-standard headroom to balanced connections, everything is designed to improve sound quality while granting a smooth and precise excursion along a wide frequency spectrum.

Features

100% Analogue
As any other BENIDUB device, Phase is precisely built with high quality components for a complex and organic sound. The optical-based design not only ensures the best signal/noise ratio for a phaser circuit but also provides the iconic old-school timbre we all love.

Versatile Routing
PHASE can be used as a 12-stage mono or a 6-stage stereo phaser. We designed it as a playable feature, allowing you to switch between the two modes with the Mode Select, clickless control. Not just a "setting", but a tool to build new phasing effect possibilities.

Performance Oriented Design In A Sturdy Case
While designing PHASE we kept our easy-to-use, performance oriented philosophy. PHASE comes in a tank-built enclosures with every control you'll ever need on board, making it an extremely playful stompbox.

Specifications
1. Input L:

1/4" Balanced or Unbalanced jack. The "main" mono input of the unit.

2. Bypass:

Turns off the out of phase signal, thereby stopping the phaser effect.

3.LFO Depth:

Sets the amount of modulation.

4.Input:

In INSERT mode, you got the usual 50/50 dry signal. In AUX mode, you got the full wet signal.

5. Mode Select:

On MONO you get 12 stages. On STEREO you get 6-stages per channel. The stereo mode can be used with a mono input to generate a mono-to-stereo output.


6. Power Input:

12VDC, 500mA, center positive, 2.1mm*5.5mm barrel connector.

7.LFO Mode:

In LINEAR mode, all the 12 (6+6) stages will receive the same modulation. In MIRRORED mode, the first batch of stages modulation will be inverted.

8. LFO Rate:

Sets the modulation speed.

9. Centre frequency:

Sets the frequency that the phaser will revolve around. The Centre Frequency determines where the middle of the comb-filter will be on the spectrum.

10. Feedback:

The feedback knob controls the amount of phase-shifted signal that gets fed back to the phase-shifting circuit.

Notes: The XPO or Stereo Prismatic Oscillator music synthesizer module is a Voltage Controlled Analog Oscillator designed for generating Sine waves, Triangle waves, Sawtooth and Spike waves, Sub-Octaves, Stereo Timbre Modulations (including Pulse Width Modulation and Wavefolding), Oscillator SYNC, Linear FM and more in the analog domain.

The XPO is designed to be the Stereo VCO complement to our Stereo Filter, the QPAS. The two modules share the core idea of complex circuits being controlled in multiple dimensions in the stereo field by a few powerful parameters. The Stereo Prismatic »

Features:

Stereo Analog VCO with eleven simultaneous outputs (five mono outs and three stereo pairs)
Modulate Timbre via Stereo Pulse-Width Modulation, Stereo Vari-Timbre, and Stereo Wavefolding
Sine, Triangle, Sawtooth, Spike, and SUB mono outs
Unique Mono versions of all Stereo Waveforms via Left output normalizations
Modulate Left and Right channels together or separately thanks to normalization and attenuverters
Center parameter adds additional timbre control to both sides of Vari-Timbre and Wavefolded outputs
Linear FM Bus features voltage-control over FM depth and a normalization of SUB to FM input for easy GROWL
Hard SYNC circuit
Two 1v/oct inputs for transposition, melody stacking, or richest FM
Expo FM input with attenuverter
Designed to pair well with QPAS, Mimeophon, and X-PAN

Specifications:

Width: 18hp
Max Depth
(incl. power cable): 45mm
Power:
145mA @ +12V
135mA @ -12V

Notes: Ten-channel version of one of the most cost-effective mixers on the market. Great sound, good EQ and handy built-in effects. Check out the 12-channel version if you prefer faders for level control.

Supplier's notes:
The Allen & Heath ZED-10FX mixer is an amazing little desk for small band mixing. It is ultra portable for carrying to the gig, and can be used for recording live or in the studio. It comes with configurable USB audio in/out making it easy to capture stereo recordings.

Guitars can be plugged in directly to the mixer using the specially designed high-impedance inputs, while the mixer has two stereo inputs for MP3/CD players or keyboards. Equipped with professional XLR stereo outputs and a flexible monitoring section with headphone and speaker feed outputs. We've added a set of fabulous effects to give shimmering reverbs and enhance your sound.

USB AUDIO FLEXIBILITY
Getting audio to and from a computer easily is now a common requirement for live sound and music production. The way this has been implemented on ZED is super-flexible and super-easy! No longer do you need to fiddle around the back of your PC to get to the soundcard inputs, only to find that the levels are all wrong and noisy. Just plug in a USB lead to your ZED, select the USB routing on the mixer and the device on your computer and that's it! CD quality audio to and from your PC or Mac. Switches and connection through jack socket terminals provide different send/return configurations:-

SEND OPTIONS:
1) Main Mix Left + Right (Post master Level)

2) Aux + FX bus (Aux is a pre-fade send, FX is a post-fade send)

3) Record Bus Left + Right (Separate stereo bus to Main Mix)

RETURN OPTIONS:
1) To Playback input (through jack socket break contacts)

2) To Stereo 2 channel (through jack socket break contacts)

ZED-10FX features a responsive 3-band, swept mid frequency EQ design which utilises MusiQ - with optimised slope (or Q factor) for equalising individual instruments.

ZED-10FX has an essential selection of 16 time-delay effects, designed for small groups who don't want to carry around an effects unit with their gear but who still want great quality FX at their gigs and on their recordings. Our DSP engineers worked hard, crafting and refining beautiful reverb algorithms to enhance every performance. These effects are available nowhere else at this price point - this quality and integration is only available from the ZED-FX. ZED effects are easily controlled using 3 buttons with 9 display LEDs. For example, the ideal delay time can be quickly tapped-in, or the perfect amount of reverb on the lead vocal can be dialled-in. There is one-stop navigation and editing - in fact, it's just as easy as using effects pedals. To alter effects parameters, the TAP button is held down and the up/down buttons pressed to adjust the specific parameter for that effect, for example, the decay length on PLATE, or the depth on CHORUS.

ZED-10FX's pre-amps are similar in design to our MixWizard range of mixers, but with a twist! Inputs 3 & 4 have a high impedance jack input capable of taking either a normal line level or a low level input from a guitar pickup. These newly designed inputs have been crafted with the aim of replicating the sound of a classic guitar or instrument tube pre-amp in a combo or head amp. An extremely high input impedance ensures loading on pick-ups is minimal and a Class A FET (field effect transistor) circuit powered from 48V is employed to give the valve-like gain stage. There is a gain "Boost" switch associated with the guitar inputs which boosts gain by 26dB to cater for instruments with very low level outputs and the overdrive characteristics of the guitar inputs are very similar to a valve (tube) circuit, being asymmetric and soft. All this makes for a wonderfully natural sound to be reproduced from the instrument, full of warmth and character.

The ZED-10FX is bundled with IK Multimedia's AmpliTube X-GEAR software, giving access to superbly modelled amps and effects.

Notes: High Quality Mic Pre with FX Loop in a compact form factor

FX Loop Send and Return supports Balanced and Unbalanced signals - interfaces with consoles or guitar pedals easily

Latching or Momentary Footswitch control of FX Loop for performance effects

Works with a wide range of microphones including condenser and ribbon mics with up to 65dB of clean gain

Aux I/O connection supporting stereo input and send

Guitar Amp output and Headphone monitor output with separate master volume control

International universal power supply included

Operates on 9V battery (No phantom power)

48V Phantom power for Condenser mics

Balanced XLR Output which supports DI and Line levels

Instrument and Balanced Line level inputs

Versatile Mix Control supports 3 modes- 100% Mic w/FX blended in, or Mic/FX balance control, or 100% FX (no Mic)

Notes: The Gemini 2412 is a creamy, extremely fat sounding dual filter based on vintage Oberheim SEM circuits. In addition to high-pass, band-pass and low-pass, there is the infamous variable filter type, which allows you to blend between several characteristics. Thanks to its dual concept, serial and parallel modes of operation and an ingenious modulation system, the Gemini 2412 should not only be able to achieve classic, extremely bulbous results, but also wafting stereo effects and lively formant sounds.

Notes: Mid-sized recording option with a bit of everything: analogue mixer, audio interface, built-in stereo recorder plus versatile digital effects. All you need in a single box.

Supplier's notes:
Don't let the classic analogue mixer design fool you - the StudioLive ARc-series mixers were built to record. With a pristine analogue front-end, high-gain XMAX-L mic preamps, and a 24-bit, 96 kHz, USB-C compatible USB 2.0 audio interface, its hybrid design makes it simple to record studio productions and mix live shows from a single intuitive console. Add in a musical 3-band analogue EQ, mic/line boost for low-level vintage synths and broadcast microphones, all-new digital effects with rich reverbs and lush delays, Bluetooth connectivity, and a stereo SD recorder... and you have a mixing and recording powerhouse that fulfils the needs of both modern musicians and content creators.

A full-featured audio interface:

The StudioLive AR12c audio interface operates at up to 96 kHz for high-definition mixing and recording. Record each of the 12 inputs, plus the main mix for even more flexible recording options. Play back up to four streams for monitoring previously recorded tracks - plus a click. Eight lauded XMAX mic preamps provide all the gain you need to capture even the most subtle details without adding any extra noise. The analogue mixer front-end makes connecting your gear to your computer intuitive, and creating monitor mixes is quick and easy. With a USB-C compatible connection, your StudioLive AR12c is ready to use as an audio interface for nearly any computer.

The channel that does it all - even Bluetooth connectivity:

The unique Super Channel can handle four stereo sources at once, making it easy to integrate consumer devices into your studio workflow. Connect a turntable to the RCA inputs, use the 1/8-inch stereo input to plug-in your smartphone, or forget the cable and connect it via Bluetooth wireless technology. You can also toggle between a stereo playback stream from your computer and playback from the onboard SD recorder, making rehearsal a snap.

A complete recording solution for studio and stage:

The StudioLive AR12c audio interface and analogue mixer is tightly integrated with state-of-the-art recording software to help you realize your creative vision. Record multitrack live performances with one click thanks to PreSonus' Capture live-recording software. Create complete studio productions with our award-winning Studio One Artist DAW. With two professional recording applications included with your StudioLive AR12c, you're ready to record right out of the box.

Stereo recording without a computer:

Imagine you're rehearsing with your band and want to record your session to analyse later. Or perhaps you're in the middle of a songwriting session and want to capture your ideas as quickly as they come to you. Either way, the StudioLive AR12c's stereo SD recorder has you covered. Insert any SD/SDHC card and you're ready to record your main mix to listen to later, so you'll never forget a great song idea or an amazing guitar solo. Doing mobile interviews for your podcast? Leave the computer at home and record straight to SD.

Effects without latency:

Monitoring with reverb and delay helps to create better recordings. Any vocalist or guitarist will tell you that a little reverb makes them feel more comfortable while performing. The StudioLive AR12c mixer's onboard effects processor lets you add high-quality reverb, delay, or chorus to any channel for a professional monitor mix. Like what you hear in your headphones? Record the Main Mix and capture the effects mix, too - with or without the dry channels - to blend with your multitrack recording. Experiment in post-production to your heart's content.

All the connections you need with a familiar look:

Packed with all the connections and controls needed to mix and record in the studio and on the stage, the StudioLive AR12c is the ultimate recording solution. The four mono channels and four stereo channels include a musical three-band EQ, plus one of PreSonus' famed XMAX mic preamps. Two dedicated monitor mixes with balanced outputs provide your musicians the custom mix they need. The USB-C compatible connector ensures your StudioLive AR12c audio interface will be the centre of your studio for years to come. And with high-resolution 96 kHz recording, a full complement of connections, and an instantly familiar workflow, the StudioLive AR12c is the perfect recording and mixing solution for the modern musician and content creator.

Notes: Desmodus's Aggressive Reverb/Delay Counterpart.

Not quite a reverb, not quite a delay, it's Desmodus's more aggressive clocked counterpart. More distortion, more in-your-face atmospheres, and synced delays for creating your tails in a whole new way. Use Electus Versio as a spacey clocked delay, as a reverb that starts with some synced echoes, or as a completely new way to create evolving spaces.

Notes: Fully redesigned from the original Cosmix, the Cosmix Pro is an eight-channel mixer intended to work nicely for performance as well as production. Suitable for line-level stereo signals as well as Eurorack levels.

Supplier's Notes:
A completely new design, with a lot of attention to sound quality, with a clean, low noise signal path, and lots of headroom.

It features the same amount of channels as the previous Cosmix, 4x mono in, and 2x stereo in.

There's one mono aux bus, and an additional true stereo AUX for all channels, with a dedicated mono and stereo return.

Each channel has a pan pot, a big push button for clickless muting, and a dedicated LED level meter to visualize channel output level.

The mono channels come with a handy low cut switch. (-3dB @80Hz / -6dB @ 45Hz)

The stereo channels have an optional +18dB gain, allowing you to easily mix in line level external gear.

The two stereo channels also have a CV input for voltage controlled panning.

There are connectors on the back for daisy chaining, or for connecting to future expanders/other mixer units.

High quality aluminium panels, available in black or silver.

The older model Cosmix is discontinued until further notice, since the parts for the drive circuit are unobtainium.

That's also the reason there is no dedicated drive circuitry in the new model.

Technical specs
22HP, 20mm deep.
+12v: 170mA, -12v 170mA

Notes: Universal drum synthesizer with roots in the analogue world on a swappable oscillator platform

Basimilus Iteritas Alia is a parameterized digital drum voice with its roots in the analogue world. At its heart, the BIA is a simple six-oscillator additive and FM synthesizer with waveform, harmonic spread, and envelope controls. An adjustable noise oscillator and an extreme take on a wavefolder round out its synthesis abilities. Its straightforward controls make sound design fun and performable: create sub-shaking kicks, snares, hats, and unique drum hits with just a few tweaks.

BIA is a classic percussion module but you'll be blown away by how much more it can do. Use it for leads, basslines, or build a whole drum kit with some external CV. Plus, the envelope output means you can use the BIA for shaping and modulating other parts of your patch.

Basimilus Iteritas Alia is available on Noise Engineering's 10HP Alia oscillator platform. Buy an Alia module and use the included USB cable to connect to the Noise Engineering Customer Portal to check out any other Alia firmware, free of charge, any time.

Width: 10HP
Depth: 22mm

What's in the box

Module
Power cable
Micro USB cable

Notes: Really neat stuff from Hexinverter. Designed with synth sounds and drum processing in mind, the Hot Glue is a unique twist on a four-channel mixer, helping to integrate effects and voltage-controlled distortion alongside built-in bus compression.

Supplier's Notes:
The Mutant Hot Glue is a versatile bus mixer for analogue effects chain design. The included analogue compressor offers series or parallel compression and a sidechain input, making it particularly well suited to drum processing. The voltage controlled distortion is based on ideas borrowed from the guitar pedals responsible for a lot of yesterday's acid style techno sounds, but improved over the guitar equivalents, and made specifically for synthesizer and drum processing. The distortion can be used in its default position, normalized to the effects send, or like every other part of the module, broken out and used elsewhere in your modular system.

Features

4 Channel Mixer with Effects Send

4 input channels, each with their own level and effects send control
Channel A mixer bypass switch and dedicated output for easy sidechain compression
Channel B is dual input, but shares level/send controls (for dual output modules, like the Mutant Hihats)
Channel C+D summed output
Main mixer output normalized to compressor input

Hi-Fidelity Analogue Compressor

Soft-knee compressor based on the same family of premium audio ICs used in some 500 Series studio gear
Dedicated threshold and compression ratio controls
Gain control dials in up to +40dB of compressor make-up gain
Compressor sidechain input for creating pumping effects
LED indicator actively displays the amount of compressor gain reduction

Voltage Controlled Analogue Distortion

A classic distortion topology reborn for modular analogue synthesizers and drum processing
In/Outputs are conveniently normalized to the module's send and return jacks
Blend control lets you adjust the mix of distorted and clean input signal
Fast responding CV input allows for complex modulation patterns and even modulating with audio signals

By default, the 4 channel mixer's output conveniently feeds into the compressor's input, giving access to easy New York style parallel compression by way of the compressor blend control. The dedicated output and mixer bypass switch for channel A allow you to use it as a sidechain source for the compressor. An effects send and return allow you to create complex effects routings within your modular system. With the number of excellent DSP and other effects modules on the market today, this makes it easy to combine modules to great effect, all within the eurorack modular domain.

Redesigned by Erica Synths in close collaboration with Hexinverter. Minor alterations were made in mechanical assembly and digital controls to address Erica synths manufacturing routines and chip shortages, but the analogue signal path is 100% identical to the original version.

In September 2022 Stacy Gaudreau - the founder of Hexinverter Electronique, announced closing down the operations. Following their announcement, Erica Synths in cooperation with Hexinverter Electronique saw a way for their incredible and truly unique music instruments to keep on inspiring musicians and finding a home in countless studios to come.
The effort and innovation incorporated in Hexinverter Electronique eurorack modules are far too great to prematurely become history. Erica Synths will take over the manufacturing, sales, and support of several Hexinverter Electronique modules. While retaining all functionality of Hexinverter Electronique modules, Erica Synths redesigned the hardware of modules and will provide support for reissue modules only.

Technical specifications

Width: 24HP | Depth: 30mm
Current draw: +70mA, -70mA @ 12V

Notes: ***B-STOCK: Box opened, product in perfect working order***


The best of both worlds, combining analogue drum circuits with samples and Korg's Multi Engine. Versatile step sequencing, built-in effects and seamless connectivity.

Supplier's Notes:
The introduction of Drumlogue marks a paradigm shift for drum machines. It combines the rich and raw power of analogue, the flexibility and convenience of digital, and the deep customisation of a unique SDK. A heavy-duty dynamic sequencer, powerful effects, and intuitive controls make Drumlogue a must-have in any setup.

The power of analogue

Drumlogue features completely new analogue circuitry from legendary Korg engineer: Junichi Ikeuchi (ARP 2600 M, MS-20 Mini, ARP Odyssey). The depth and richness of its sound is on a whole new level. New analogue circuits for bass drum, snare drum, low tom and high tom provide a solid foundation, and elevate tracks with harmonic richness and a thick low end.

The versaility of digital

Drumlogue has 7 digital parts: 6 sample-based and 1 Multi Engine based. The sample-based parts can play a wide selection of pre-loaded PCM samples alongside imported user samples. These can be easily loaded into Drumlogue by connecting to a computer via USB and simply dragging and dropping into its main memory.

Endless creative potential

The wildly popular Multi Engine from Minilogue XD is made even more powerful: in addition to Variable Phase Modulation (VPM) and Noise generator engines, the Multi Engine in Drumlogue features a new user slot able to play fully-fledged synth voices - providing vast sonic possibilities never before heard on a drum machine.

Custom Synths

Synth voices in Drumlogue are so much more than static waveforms. Custom synths can be built to not only generate sound, but can also draw on built-in filters, LFOs, MIDI controlled polyphony

Exclusive "Nano" plugin

Korg has collaborated with popular plugin developer "Sinevibes" to create a brand new synth plugin for Drumlogue: Nano. This exclusive plugin explores the power behind the newly expanded Multi Engine and gives an incredible first taste of the platform.

"Nano" is a full-fledged virtual analogue synth with a broad array of features and customisable parameters. The synth engine has dual oscillators with optional ring modulation, a 4-pole state-variable filter with soft clipping distortion, built-in EG and built-in multi-waveform LFO.

Sequencing powerhouse

At the heart of Drumlogue is a flexible, easy-to-use, and extremely powerful 64-step sequencer. This makes it easy to create complex patterns and polyrhythms that elevates the music creation process. Innovative features are available including per-step probability, per-step alternate trigger patterns, per-step micro offsets, per-track groove patterns and much more. With the clear OLED display, it's also easy to follow and edit your sequences visually.

Chain mode makes creating long and interesting patterns simple. In loop mode you can switch between several variations to play sequences in new and interesting ways. The Motion and Accent recording functions are fast and intuitive, and if you want to try new things on your track, the randomisation function is there to help you.

Effects and customisation

Drumlogue has high-quality effects across three categories that can be used simultaneously: delay, reverb and master effects. The send amounts for delay and reverb effects are set independently, with multiple return points also available. Master effects add that final polish to the sound and can be bypassed on a per-part basis, meaning it's possible to send the effect to specific audio parts. A sidechain bus is also available to the master effects section.

Drumlogue has an audio input, so you can process other instruments through Drumlogue's effect chain, making it an ideal companion for your studio setup.

Connectivity

With a wide range of I/O, Drumlogue can be integrated seamlessly with your rig. A USB-A port supports connectivity with USB MIDI class-compliant devices, meaning volumes can be controlled with the faders on a nanoKONTROL 2, or sounds triggered by the pads on a nanoPAD 2.
It almost goes without saying that Drumlogue easily syncs with other gear via the MIDI in/out, sync in/out, or via USB MIDI.

Four individual outputs are available, in addition to headphone and main L/R. Any part can be assigned to any output, allowing for expanded routing versatility with external processing and multi-track integration.

Ease of use

Drumlogue is incredibly easy to use - having been designed with simplicity and accessibility in mind. The most important parameters for the main drum parts have dedicated knobs on the front panel for on-the-fly adjustments, as well as dedicated volume pots for each part to speed up the mixing process.

A wide and clear OLED screen coupled with a simple UI and 4 dedicated encoder knobs makes the navigation process fast and smooth.

Design

Unlike other drum machines, Drumlogue's main panel is slanted. This offers superior ergonomics and visibility, while a brushed aluminium body and wooden side panels add to the premium look and feel.

Specifications

Polyphony: 11 voices (*)
(*) User synths may be played polyphonically via MIDI, the actual voice count will depend on the synth's implementation

Sound Engine
Analogue:4
PCM / User samples: 6
Multi-engine(NOISE, VPM, User Synthesizer): 1

Number of Programs (including rhythm patterns): 128 (64 preset programs by factory default)
Effects: Reverb, delay, master

Inputs / Outputs
Headphones
OUTPUT, (L/Mono, R/Audio, Out 1-4)
Sync In/Out
Audio In, MIDI In/Out
USB A (To Device) (Only for MIDI controllers)
USB B (To Host)

Power supply: AC adapter (DC9V)
Dimensions (W × D × H): 317 × 189 × 73 mm/12.48" × 7.44" × 2.87"
Weight: 1.4 kg/3.09 lbs.
Included items: AC adapter, Precautions, Quick Start Guide

Notes: Add warm dimensionality and luscious tape saturation to your signal. Teleport the tones of yesteryear to your board. Effortlessly create a huge range of beautiful, distinctive, and enveloping vintage sounds. From the inherent warmth and luscious tape saturation to the forgotten art of how these machines were manipulated, Deco brings this original inspiration back, giving you these vintage tape effects from the earliest recording studios, right on your pedalboard.

Deco's Tape Saturation smooths out your sound with familiar and delicious tape compression and saturation, while fattening your tone with subtle tape-driven transparent overdrive.The Doubletracker provides the power to shift your sound in many ways, easily allowing you to achieve syrupy slapback tape echoes, psychedelic tape flanging, and gorgeous tape chorusing sounds.
Our second generation Deco gives you the same gorgeous reel-to-reel tape sounds from our original, while adding several significant new features, incorporating technological advancements, hardware improvements and design enhancements to give you additional flexibility, power, and ease of use on stage and in the studio.

Full MIDI implementation means you can control just about every switch, knob, and setting remotely by sending MIDI commands from your controller or DAW via Deco's EXP/MIDI jack or USB-C connection. Lag Deck delay time can be synchronized via MIDI Clock Sync, and the sync setting can be saved for each preset. 300 MIDI preset locations are available for loading and saving your favorite settings.

Deco now comes with an all-new cassette tape voicing that employs an auto level control (ALC) process common to many high-end cassette tape recorders, resulting in a compressed, fat tone. In addition, a new dedicated Tone knob lets you adjust the tone of the Tape Saturation exactly to your liking, from dark to bright.

A premium analog JFET input circuit ensures superb responsiveness to your playing, and you can select mono or stereo input with the flick of a rear panel switch. All this, plus a new ARM DSP chip provides more processing power for every sonic nuance, with less energy consumption on your pedalboard.

Features

High impedance ultra low-noise discrete Class A JFET TRS stereo input.

Low impedance independent TS stereo outputs.

Expression pedal input allows the connection of a TRS expression pedal, MiniSwitch, MultiSwitch Plus, or TRS MIDI connection.

USB jack for controlling via MIDI from a computer or for performing firmware updates.

Dedicated tap tempo & On/Off footswitches

Premium JFET analog front end

Ultra low noise, high performance 24-bit 96kHz A/D and D/A converters provide uncompromising audio quality

520MHz ARM Superscalar processor

32-bit floating point processing

20Hz to 20kHz frequency response

Audio Input Impedance: 1M Ohm

Audio Output Impedance: 100 Ohm

Strong and lightweight anodized dark gray aluminum chassis

9V DC power supply included

Power requirements: maximum 9 volts DC center-negative, with a minimum of 300mA of current

Dimensions: 4.5" deep x 4" wide x 1.75" tall (11.4 cm deep x 10.2 cm wide x 4.4 cm tall)

Designed and built in the USA

Notes: Limited black edition of the excellent stereo Dark Star pedal, offering premium reverb with beautifully creative pitch shifting, filtering and bit crushing options. Superb value for money.

Supplier's Notes:
Dark Star Stereo Flagship Reverb Pedal

The continued pull, the drift unabated, the controlled wash of gravity and the chaotic meander of its combined uncertainties. In fact, the original and highly loved Dark Star is a pedal that historically was OBNE's most popular reverb. People bonded with its warmth and aliasing, its long trails and the way it encouraged you to turn the mix fully up. Now, it's in with the new. Dark Star Stereo expands on the promise of ambient reverb and is a pitch shifting, bit crushing, filtered reverb pedal with just about every feature you could ask for. One massive stereo voice, with a wide suite of controls that likes to go anywhere in your signal chain - all that's left is for you to decide just how dark you must go.

Reviving the magic of the long-trail lo-fi reverb algorithm that made Dark Star a breakout hit years ago, Old Blood Noise Endeavors announces a new Dark Star for a new era, with a drastically expanded feature set and improved signal quality that is sure to draw in old fans and new. New features like Stereo Input and Output, on-board Presets, Trails, Expression control over all parameters and MIDI control, of both Parameters and Presets, all help to give more versatility to this device than ever before. Beyond that, the new Dark Star does away with the three-mode toggle, instead creating a single mode combining all the Pitch-Shifting, Bit-Crushing, delayed goodness of the original. Access your favourite sounds as well as new combinations, with new shapers like Filter, Multiply, Volume and Stereo-Spread.

Notes: Excellent Eurorack sequencer based on random chance and evolving patterns. Dial in a series of notes and build melodies, generate and tweak patterns in real time. Huge depth for studio production or live performance.

Supplier's Notes:
The Melodicer from Vermona is a CV/Gate sequencer with an innovative concept; the melody sequencer offers twelve faders for setting the note probability and two dice-(or random) buttons for generating melody and rhythmic structure.

Notes: FC10S is designed for any mid-to-large room requiring bass extension, the Fluid Audio FC10S active subwoofer is the perfect solution for recording/mixing studios, gaming rigs, home theaters any application that would require solid and accurate bass reproduction.

Many types of music benefit from bass extension from Hip-Hop, to House, to Rock. Being able to hear your mix with bass extension is critical to accurately creating your music. The FC10S subwoofer allows you to hear every detail down to 20Hz, which gets below your hearing threshold, and down to where you actually feel it.

Mix Engineers want the confidence to know that their mixes translate well on all types of systems. That is why we included a standby footswitch. With a click of the included foot pedal, you can turn the bass on or off, and audition your mix with bass extension and without.

The FC10S also has two built-in EQ settings that allow for two different settings depending on your music: A more conventional Flat response, as well as a Punch setting that is perfect for Dance or other mid-bass heavy music.

For further flexibility, the FC10S has a variable phase adjustment to fine tune the phase for optimal matching to your L/R monitors (0-180-), a variable low pass crossover filter control (50-200Hz) and a 80Hz high pass filter (used with foot switch) for satellite connections. We have also included a ground lift switch as well, to minimize ground hum with some home wiring.

Highlights
Active subwoofer
200 Watts of class D power with switching power supply
10-inch composite paper cone with high temperature voice coil and damped rubber surround
Ground lift switch
Bass-reflex vent port on front baffle for ease of placement
Amplifier standby function to conserve energy
XLR balanced and 1/4 balanced/unbalanced inputs and RCA inputs
XLR balanced and 1/4 balanced/unbalanced outputs
Variable lowpass filter control: 50Hz-200Hz
Variable Phase control: 0 180-
Switch for both Flat and Punchy settings
80 Hz highpass filter(with foot switch) for satellite connections
Included footswitch allows you to turn FC10S on and off for auditioning with bass and without

Specifications
Frequency response: 20-200Hz
Total amplifier power: 200 watts
Signal-to noise: > 100dB (typical A-weighted)
Polarity: positive signal at + input produces outward LF cone displacement
Input impedance: 20k ohms balanced, 10k ohms unbalanced
Max SPL 107dB Flat / 108dB Punchy setting
Power: factory programmed for either 100-120V ~60Hz, 220-240V ~50Hz
Protection: RF interference, output current limiting, over temperature, turn on/off transient, subsonic filter, external main fuse
cabinet: vinyl-laminated, high acoustic efficient MDF
Size: 15.25 x 12.5 x 15.5, 387 x 317 x 394mm
Weight: 28.2 lbs / 12.8 kg

Notes: Four-part probabilistic rhythm crossfader

Confundo Funkidos is a rhythm crossfader and mute utility. Patch two pairs of rhythms to the left and right inputs, then use the CV-controllable crossfader and three Curve algorithms to fade between them and combine them in different ways. Each channel has a mute switch which can be used to bring a voice in and out of a patch at will. Tap the Burn button for some instant fills, and your percussion performances will never be the same.

New to the second version is the addition of four Accent outputs. Accent patterns are generatively created using the rhythms at the inputs, adding a new, dynamic dimension to even the simplest of trigger sequences. The Accent jacks output high or low gates, which can be used with dedicated percussion modules or as modulation sources in a patch.

The Burn functionality has also been expanded, with the addition of a potentiometer for more versatile and hands-on fill creation. Even the Mute switches have been expanded with three positions: each channel can output triggers but not receive Burn fills or output accents when set to the middle position.

If you want to liven up your percussion system with a completely unique and hands-on utility, Confundo Funkidos brings modular performance to a whole new level.

Size and Power
12HP Eurorack
+12v: 55mA
-12v: 15mA
Confundo from Latin confundo - "to blend"

Funkidos agitation disease - from Flemish fonck "agitation" with suffix dos for "two"

"Second blended agitation"

What's in the box?

Module
Power cable

Nosie Engineering no longer include screws with newly packaged modules, but Bulk screws are available for purchase separately.

Notes: Ohm Force's genre-defining 'shaper' distortion plugin comes to Eurorack in this neatly designed module. Over 100 distortion programs in full stereo, with plenty of hands-on control and extensive CV modulation options.

Supplier's Notes:
Time to get away with murder

From the plugin that redefined distortions forever

111 different distortions and shapers in one single 14hp module

Full stereo

Advanced performer modes

Back on Eurorack

Ohmicide Eurorack is an adaptation of the legendary distortion plugin that defined the now well populated category of "shaper" effects. Amongst the numerous things that made it a hallmark plugin was the carefully crafted distortion library covering all things known and many more unknown. All of those 111 distortions are now ready to burn your finger tips in a remarkably versatile module delivering huge sonic possibilities. ant let you change the texture of your VCOs, drums and samples in subtle or brutally unsubtle ways. Use all sorts of distortions, including bitcrusher, freezer, filtering and jellyfish variety.

Wiggle. Listen. Drool.

With a routing redesigned for Eurorack you'll need little learning to go straight to soundscape heaven (or hell, preference may vary). Shape the frequencies you want with the XOVER and the two Low Pass Filters. Explore the impact on all of your sounds, from mono VCO to stereo drums loops. Cycle through TYPE to find a fit or get nice surprises then tweak BIAS and MOD to explore new forms of madness.

It's alive

Ohmicide Eurorack features CV for all of its parameters including four with attenuverters. It also has automatic gain staging that is essential to the distortion delivering texture, not just loudness. And for your live experience we incorporated a performer mode that let you store and even automate preset switching. Ohmicide is lovingly crafted based on decades of experience in distortions. It's a module to lose yourself in for long sessions of sound exploration - or simply to get uniquely aggressive leads and drones.

Specifications:

Width: 14HP
Depth: 26mm
+12V: 120mA
-12V: 10mA
+5V: 0mA

Audio

Sample Rate: 48kHz
Hardware audio converters bit-depth: 24-bit
Internal processing bit-depth: 32-bit floating point
True Stereo Audio
High fidelity Texas Instruments Burr-Brown audio converters

Controls

Knob resolution: 16-bit (65536 distinct values)
CV inputs
Voltage: +5V (0..5V compatible)
Resolution: 16-bit (65536 distinct values)

Memory

Current distortion type, screen contrast and saver mode, TYPE and FAM CV +5V or 0..5V options
16 sequences
8 steps, each step being a snapshot of all knobs and switches
All knob options
Sequence length
Step reset mode

USB Port

Type: Micro-B
The USB port is only used to update the module firmware.

Notes: ALM Eurorack cases are available in a range of sizes all including an integrated powered bus boards.

The cases all feature anodised aluminium construction, an on/off switch, rubber feet, and high quality switched powered bus boards with numerous keyed headers and ample power capacity.

These are simple and compact Eurorack cases, perfect for small, focused systems, taking along on travels, or as a tabletop addition to a larger setup.

Cases are available in 4 sizes; 3U 84HP / 6U 84HP / 3U 52HP / 6U 52HP sizes. They all offer 1 Amp on both the -12V and +12V rails per row.

Great modern cases

The ALM powered Eurorack case was originally designed for the System Coupe. Wider interest has seen it evolve into a range of different sized cases being made available by themselves.

A fixed solid bus board provides quality ample power and plentiful keyed power connectors. The shielded DC/DC power converter is low noise and includes overload and short circuit protection. Fixed, quality mounting rails are used over sometimes frustrating sliding nuts. The case has a great looking all anodised aluminium construction that is both strong and light.

The case proportions are designed to look great on a table or desk (not too deep, just enough) and also be easy to fit in a bag and transport.

Decksaver case covers are available currently for the 3U/84HP, 6U/52HP, and 6U/84HP cases.

6U / 84HP

Provides up to 2 Amp power total on each -12V & +12V rails (1 Amp total per row)
Connections for up to 32 modules.
Includes 5 Amp power 'brick'

Notes: ALM Eurorack cases are available in a range of sizes all including an integrated powered bus boards.

The cases all feature anodised aluminium construction, an on/off switch, rubber feet, and high quality switched powered bus boards with numerous keyed headers and ample power capacity.

These are simple and compact Eurorack cases, perfect for small, focused systems, taking along on travels, or as a tabletop addition to a larger setup.

Cases are available in 4 sizes; 3U 84HP / 6U 84HP / 3U 52HP / 6U 52HP sizes. They all offer 1 Amp on both the -12V and +12V rails per row.

Great modern cases

The ALM powered Eurorack case was originally designed for the System Coupe. Wider interest has seen it evolve into a range of different sized cases being made available by themselves.

A fixed solid bus board provides quality ample power and plentiful keyed power connectors. The shielded DC/DC power converter is low noise and includes overload and short circuit protection. Fixed, quality mounting rails are used over sometimes frustrating sliding nuts. The case has a great looking all anodised aluminium construction that is both strong and light.

The case proportions are designed to look great on a table or desk (not too deep, just enough) and also be easy to fit in a bag and transport.

Decksaver case covers are available currently for the 3U/84HP, 6U/52HP, and 6U/84HP cases.

6U / 52 HP

Provides up to 1 Amp power on each -12V & +12V rails.
Connections for up to 9 modules on busboard, with additional 'flying bus board' included that adds up to 12 connectors.
Includes 2 Amp power 'brick'

Notes: ***B-STOCK: Box opened, product in perfect working order***


The first release from Teenage Engineering's EP Series. Sample, program, sequence and produce in one compact, retro box. Bundled here with the extremely limited edition EP-133 KO II vinyl volume one.

Supplier's Notes:
Get ready for round 2

Meet the next evolution of the world's most sold sampler. based on the legendary PO-33 K.O!, the new EP-133 K.O. II adds more power, more sampling capabilities, a fully reworked sequencer and brand new punch-in 2.0™ effects. introducing a workflow that lets you go from idea to track faster than ever. it's pocket operators gone pro.

The champ is here

A versatile machine with an impressive set of features, K.O. II is the new champion in and outside the studio. unrivaled by anything in its class, this is the sampler you've always wanted at the incredible price of just $299

Record sounds around you, sample your voice, favorite synths, vinyl records or whatever audio that you've got on your phone.

Sequence your samples and loops. make use of the curated selection of drums, bass and keys that come pre-loaded on your K.O. II.

Tweak and automate things like filter, pitch and more... add stereo effects, compressor and next generation punch-in effects.

The sequencer engine of the K.O. II provides an intuitive, fast way of building up beats and variations using 4 groups x 12 patterns. like most DAWs, you can instantly swap patterns per group, experiment with different combos to find what beat and bass lines work together. the commit button helps you freeze a point in time and move on, adding a verse or a break. it all happens in real time while playing.

One-two punch

vintage style keys with a modern touch, combining tactility with pressure sensitivity.

EP-133 K.O. II vinyl

A 10" record full of sounds for your creative soul to digest. side a contains a mix to make you laugh or love. side b provides you with one-shots and other sounds ready for manipulation. a record to fit every musical preference imaginable. (Two-sided 10" vinyl, weight: 170 g | 6 oz, 45 rpm)

Notes: Arturia's 88-key controller is designed for those who place the emphasis on keyboard quality and feel. Piano-style hammer action makes it a nice choice for serious players.

Supplier notes:
Creating music in the digital world can be difficult. So many options, so many new things to learn. KeyLab Essential lets you focus on what's important.

8 pads, 9 rotaries, 9 faders, and an expressive keyboard, but so, so much more. Music is at the heart of this controller. Every aspect of KeyLab Essential has been carefully chosen to give you the best possible experience when creating and performing. KeyLab Essential makes navigating inside your recording software a breeze thanks to the dedicated DAW Command Center, and makes browsing your presets an exciting and inspiring experience.

Spend less time with a keyboard and mouse, and more time creating, performing, and playing.

The KeyLab 88 is a professional-grade 88-note MIDI keyboard controller designed with the working musician in mind. Featuring a new hammer-action keybed from Fatar and deep integration with our award winning Analog Lab software, the KeyLab 88 is unique with its robust, solid metal construction and classic wooden side panels.

An extensive array of controls, a stylish yet amazingly lightweight design, and brilliant integration with laptops and tablets: KeyLab 88 is perfect for modern keyboard players, pianists, demanding stage performers, and professional producers who will not compromise on quality. KeyLab 88 sets a new standard in professional controller keyboards.

As a professional hybrid synthesizer, KeyLab 88 offers the immediacy of a hardware synthesizer combined with the flexibility of a software-based solution.

Thanks to the top quality, hammer-action Fatar keybed, the KeyLab 88 is the ideal companion for demanding performers.

Notes: Ultra-versatile stereo reverb pedal with eight contrasting algorithms for flexibility and character. Expression pedal highly recommended for real-time hands-free modulation.

Supplier's Notes:
Space Reflections

ROOMS is a stereo, multi-function digital reverb capable of searing volume, gated walls of sound, and long, trailing reverberant ambiances with an intuitive array of controls designed with live mood-bending in mind.

ROOMS was designed to the highest standards of flexibility and audio fidelity. A studio-quality mixer section provides independent DRY and FX controls over six meticulously programmed reverb algorithms; ROOM, DIGIT, PEAK, GATE, WAVE, and GONG. Each different verb is capable of a universe of sounds, and ROOMS is here to help you explore them.

ROOMS' creative I/O switching and dual-mono dry signal lines allow for a wealth of possible mono and stereo configurations, making it easy to route signals for parallel processing or stereo amplifier setups.

Controls

FREQ: Controls the frequency parameter of the current mode.

DEPTH: Controls the depth parameter of the current mode.

TIME: Controls the reverb time in all modes.

DRY: Controls the volume of the dry signal, from -inf to 20x gain.

FX: Controls the volume of the reverb signal, from -inf to 20x gain.

ALT: Engages the ALT mode, switching between two sets of controls. When active, FREQ is controlled with the F knob, DEPTH with the D knob, and TIME with the T knob. Additionally, the ALT mode turns on expression control of either FREQ or TIME using the F?T Switch on the side of the pedal. NOTE: Expression control ONLY works in ALT mode and when an expression pedal is plugged in.

Expression Pedal: Almost any expression pedal will work with ROOMS. When not plugged in, the controls work as normal. NOTE: Expression control ONLY controls the F or T knobs when ALT mode is engaged and when an expression pedal is plugged in.

Modes & Parameters

FREQ knob : DEPTH knob

1 - ROOM: Tone of Decay : Pre-Delay
A classic reverb that simulates many different rooms.

2 - DIGIT: Delay Time : Delay Feedback
A filter matrix verb capable of creating otherworldly resonances and fractured repeats.

3 - PEAK: Filter Frequency : Filter Resonance
A super intense bandpass filter combined with an ambient reverb.

4 - GATE: Decay Tone : Gate Response Time
A gated reverb. Short reverb times create a classic gate effect, long reverb times create a controllable freeze effect.

5 - WAVE: Modulation Frequency : Modulation Depth
Creates a pitch vibrato effect. Lowering TIME will blend out the reverb signal, allowing sweeps from chorus/vibrato to long modulated reverbs.

6 - GONG: Modulator Frequency : Blends from Aliasing (left) to Ring Modulation (right)
Ethereal, crushed reverb sounds guaranteed to make you star in the upcoming remake of DUNE and live out your sci-fi fantasies of space travel and galactic domination.

Specifications

Dimensions: 5.95" x 3.86" x 2.96" (including hardware).
Weight: 18 oz.
Power: 80 mA, 9V (runs on a standard 2.1 mm negative center 9V adapter).

Notes: The Power of Simplicity.

The SL Keyboards are nothing less than the reinvention of the high-end keyboard controller.

True innovation.

More than 30 years' experience in exclusive keybeds meets an all-new, powerful, operating system. Perfect for you to control your hardware and virtual instruments. All provided in a powerful new refreshing way. Working together with musicians we have created a user interface which is perfect for quick navigation and setup, but also gives you excellent in-depth control. The SL is ready to be at the very heart of your system.

A Great Keyboard for a Grand Touch.

The SL88 Grand uses the best-graded hammer action keybed with Ivory Touch and wooden keys, to give you the natural feel of a well-balanced grand piano. Each of the keys provides 3 contacts for superior performance. The results of this combination are simply amazing. From the slightest pianissimo up to the strongest fortissimo, the keys translate every nuance of your performance in an inspiring and truly superb way.

The lightness of the authentic touch.

The SL88 and 73 Studio adopts the latest hammer action keybed technology from FATAR giving the best piano touch feeling. TP/100LR is remarkably lighter than any other. Each of the keys provides 3 contacts for superior performance. With the respect of the full weighted touch of the real piano action, the new design guarantees a very fluent and authentic feel. The results of this combination are simply amazing.

Form follows performance.

With its compact profile, the SL is an extremely portable professional controller. Thanks to a perfect integration with the keyboard, it weighs less than 14 Kg for the 88 Studio version and less than 12 Kg for the 73 version. Even with its high-end graded hammer action/wooden keyboard, the SL88 Grand weighs less than 21 Kg. The SL is studio and stage ready with a rugged full metal casing. Sculptured endcaps made of a highly resistant synthetic material help to shield the premium keybed perfectly and provide a safe grip when handling and transporting.

Total access with total ease.

Located in the centre of the instrument is a razor-sharp TFT colour display. In combination with the high quality six-way controller knob, you can navigate through all SL functions fast and with ease. Functions such as switching through the four zones are achieved by moving the controller, and then by clicking and turning the same knob again, you can select and adjust the desired parameter. Simple, intuitive and fast! Additionally, the three pushbuttons to the right of the control knob bring you back to the top-level from any location in the system with just one push.

Real-time control.

The SL offers three X/Y stick controllers, not just for performance but also for direct control and manipulation of any desired sound parameter. Stick one is spring-loaded for both X/Y directions. The typical use for this stick is pitch and modulation control. Stick 2 is spring-loaded in X direction only. Stick 3 is free in X and Y directions, ideal for panning, cross fading and parameter control. All sticks feature an elegant, aluminium control shaft which feels perfectly balanced and expressive between your fingertips.

Magnetic rail system.

With the innovative Magnetic Rail System at the rear of the SL, you can easily adapt a note stand or an extension plate to hold your written notes, music, laptop or tablet. It works as brilliantly easy as it looks. Just click the brackets into the backrail to match the position you need for your accessory items.

Package content
SL88 Studio
Studiologic PS100 switch pedal
Power adapter

Keyboard
88 Keys, TP/40WOOD Graded Hammer Action, Ivory Feel
Triple switch detection system
Aftertouch
Touch:
Soft, Medium, Hard, Fixed (programmable)
6 Editable user velocity curves (with SL Editor)

Features:
250 Programs
12 Programs Groups
4 Programmable Zones
2 MIDI Ports separately assignable

Controls / UI:
3 Programmable sticks
Rotating encoder with navigation controls
3 Function buttons
Display
Colour graphic LCD - TFT
320 x 240

Connections:
Pedals: 2 switch, 1 continuous, 1 universal
MIDI: In, Out1, Out2
USB: USB to Host, MIDI, USB Powered

Power supply:
DC IN: 9V
Adapter
Input: 100-240V / Output: 9V-1A

Size & weight

Width: 126 cm / 49,6"
Depth: 31 cm / 12,2"
Height: 12,5 cm / 4,9"
Weight: 13,7 Kg / 30,2 lbs

Package content
SL88 Studio
Studiologic PS100 switch pedal
Power adapter

Compatible accessories:
Softcase SIZE B, SIZE C
Magnetic Music Stand TYPE A
Magnetic Computer Plate TYPE A

Pedals:
PS/100, PS/150, PS/250
VFP1/10, VFP1/15, VFP1/25
VFP2/10, VFP2/15
SLP3-D
VP/25, VP/27
FP/50

Notes: Iridium

Leave Your Amp At Home.

Nothing reveals the true nature of your guitar and your playing like a world-class tube amp driving a perfectly matched speaker cabinet in a great sounding room. Now there is a pedal that truly delivers that sound and feel, with simple controls for effortlessly dialling in the perfect amp tone when going direct. Discover inspiring tube amp responsiveness, unprecedented impulse response speaker cabinet realism, and controllable natural sounding room ambience.

Iridium gives you three iconic amplifiers, with a total of nine impulse response speaker cabinets that complement the tonality of the amp. Skip the hassle of lugging around or miking amps. Place Iridium on your pedalboard and send gorgeous stereo amplifier tones, stunningly realistic cabs, and lush room ambience direct to a recording interface or PA system. With Iridium, it's a snap to dial in a direct tone that will truly inspire and sound great whether you are monitoring through in-ears, floor wedges, reference monitors, or studio headphones.

Three Iconic Amplifiers

The Matrix Modeling process captures all the subtleties and unique tonal qualities of each amplifier. Strymon have taken three iconic tube amps with distinct characters and mathematically modelled every aspect of their circuitry with absolute precision to deliver the response, feel, and inspiring experience of playing through the original amps at their best. Taking the process a step further, Strymon have hot-rodded each amp to provide an extended range of tonal options beyond what was available from the original designs.

Nine Stereo IR Cabinets

Iridium's speaker cabinets offer a level of realism and responsiveness unprecedented in outboard effects. Iridium delivers full stereo 24bit 96kHz resolution for the entire 500 milliseconds of its speaker cabinet impulse responses. Until now, IRs of this resolution have only been available for use within studio recording software. Iridium's breakthrough technology means you can use the very best impulse responses available, bringing maximum realism to your pedalboard.

Adjustable Room Ambience

Iridium's hybrid room reverb combines a 256 millisecond stereo impulse response with Strymon's reverb tank algorithm for extended decay. This combination places your amp and cab in a natural sounding room (small, medium, or large), creating a space for your amp to open up and breathe.

Round Amp - Based on* a Fender Deluxe Reverb

The Deluxe is one of the most recorded amps in history for good reason. This amp is clean, bright, and mid-scooped, with plenty of headroom. At higher Drive settings it delivers an overdriven sound unique to its architecture. Strymon chose the Deluxe's Normal channel for its round tone that plays well with pedals. While preserving access to all the tones originally available with this channel, our model gives you something extra: a midrange control. With the midrange at noon, you get the original fixed-resistor value and standard tonal characteristics of the Deluxe. Turn down the midrange for a more scooped sound, or turn it up for tweed-era tones.

Chime Amp - Based on* the Brilliant channel of a Vox AC30

The amp that defined the guitar sound of the British Invasion. Our model of the AC30 Brilliant channel (Top Boost) is jangly, bright, and chimey, providing air for subtle passages with a light touch, and bite when you want to dig in. For this amp, the Middle knob acts a Tone Cut knob, providing high-end roll-off just before the power tubes, per the original AC30 design. In addition to the full available gain of the original amp, toward the top end of the Drive knob's range of travel, Strymon have added a frequency-shaped front end boost to tighten the low end while driving the amp further into saturation.

Punch Amp - Based on* a Marshall Plexi (Super Lead model number 1959)

This powerful amp is meatier, with higher gain than the other two amps, and has a powerful midrange response. This amp features a buttery, smooth overdrive. At higher Drive settings it will deliver all the high gain distortion and growl this amp is known for, and then some. Setting the Drive control at around 2 o'clock gets you the maximum gain the original Plexi design allowed. Beyond that, our model has some additional gain on tap, giving you access to custom hot-rodded Plexi high gain tones.

*All product names are trademarks of their respective owners, which are in no way associated or affiliated with Strymon. These product names, descriptions and images are provided for the sole purpose of identifying the specific products that were studied during Strymon's sound design process. Fender and Deluxe Reverb are registered trademarks of Fender Musical Instruments Corporation. Vox is a registered trademark of Vox R&D Limited. Marshall is a registered trademark of Marshall Amplification Plc.

A Carefully Curated Cab Collection.

Iridium comes pre-loaded with a carefully curated collection of premium cabinet impulse responses from OwnHammer, Celestion, cabIR and ValhallaIR.

Round A - Deluxe Reverb 1×12" by OwnHammer
Impulse captures a vintage Fender Deluxe Reverb open back 1×12" combo loaded with a 1978 Fender CTS ceramic 12" speaker.

Round B - Blues Junior 1×12" by CabIR
Impulse captures a 1×12" Blues Junior cabinet, loaded with a Jensen C12N speaker.

Round C - Vibrolux 2×10" by cabIR
Impulse captures a Fender Vibrolux from 1965 with 2×10" Jensen C10NS speakers from 1965.

Chime A - AC30 2×12" Alnico by OwnHammer
Impulse captures a Vox AC30/6 open back fawn 2×12" combo with 2001 Celestion T0530 Blue AlNiCo speakers.

Chime B - 1×12" Alnico by Celestion
Impulse captures Celestion Blue Alnico speaker in a closed back 1×12" cab.

Chime C - Mesa 4×12" by ValhallaIR
Impulse captures a 4×12" Mesa Boogie "Halfback", which is loaded (open back) with two Black Shadow MC-90 speakers from CelestionTM and two Black Shadow EVM12-L from ElectroVoice.

Punch A - GNR 4×12" by OwnHammer
Impulse captures a 1971 Marshall 1960B "basketweave" 4×12" cabinet.

Punch B - 2×12" Vintage 30 by Celestion
Impulse captures a Celestion Vintage 30 in an open back 2×12" cab.

Punch C - Marshall 8×12" Alnico by cabIR
Impulse captures a re-issue of the 1965 Marshall 8×12" full stack cabinet, loaded with Celestion T652 AlNiCo speakers.

Load Your Own Impulses.

It's easy to replace the pre-installed IRs with custom IRs from your own collection by using Strymon Impulse Manager software.

Stereo Output
Operates at instrument and Line Level input sources
Discrete transistor headphone amplifier
Expression pedal input provides seamless morphing between knob positions (Expression mode), or smooth pre/post volume control with logarithmic taper (Volume mode)
USB jack for connecting to Strymon Impulse Manager software
to add and edit your own speaker cabinet IRs
Compatible with Strymon MultiSwitch Plus for remote selection of up to 4 presets
Full featured MIDI control accessible via EXP Jack for remote parameter control and access to 300 preset locations (requires Strymon MIDI EXP cable or MIDI to TRS interface)

Audio Quality

Ultra-low noise, high performance 24-bit 96kHz A/D and D/A
converters provide uncompromising audio quality
Super high performance SHARC and ARM co-processors
32-bit floating point processing

More

Transparent Analogue Buffered Bypass
Strong and lightweight anodized black aluminum chassis
9V DC power supply included
Power requirements: maximum 9 volts DC center-negative, with a minimum of 500mA of current
4.5" deep (11.43 cm) x 4" wide (10.16 cm) x 2.4" tall (6.1 cm)
Designed and built in the USA

Notes: The Serge GTO is a newly designed, complex multi-functional module which can be patch programmed to provide various slew and sample functions both for audio and CV signals, but also act as a (dual) oscillator or filter or bitcrusher or ... It is one of the essential Serge modules. The GTO is an offspring of the famous Serge SSG.

The Smooth section will place a positive and negative slew on input voltage transitions for lag effects, voltage controlled portamento and for low frequency filter applications. In Cycle-mode (cycle jack patched to the input), the Smooth side “will oscillate yielding a voltage controlled triangle wave LFO. A high level into the HOLD input will enable the Smooth Function to be used as a track-and-hold circuit with voltage controlled slew rate.

The Stepped function can be used as a sample-and-hold with voltage controlled slew rate limiting. In Cycle mode, a pulse applied to the Sample input will generate complex staircase waveforms for control voltage applications and for use as audio signals.

Each side has a temperature-compensated 1V/Oct input for use as an oscillator with a frequency range of up to 20kHz (left) and 8kHz (right). Each side tracks over 5 or 6 octaves.

The Coupler is an internal comparator which compares the output levels of the Smooth and the Stepped Generators. This output is useful for generating complex control voltages or random voltages.

Dimensions:
18 HP
25 mm deep

Current draw:
45 mA +12V
40 mA -12V

Notes: Multi-operator phase-modulation platform oscillator ideal for lovers of drone

Toros Iteritas Alia is a multi-operator, three-algorithm phase-modulation oscillator. Taking inspiration from Nosie Engineering's favourite things about FM synthesizers and doing away with complicated interfaces and mysterious controls, Toros prioritizes immediacy and, of course, epic sounds.

The unique Blendex controls allow the user to route each oscillator to be a PM for the next oscillator in the algorithm or direct to the output. Fine-tune the output for your needs with the frequency controls that constrain the range to span a minor third, an octave, or two octaves. Dial in and morph between anything from dark and noisy to tonal to sub-shaking sounds with ease with the completely CV-able interface.

Designed with drones in mind, Toros is the perfect tool for long, evolving textures and dark drones - or big, clangorous tones if that suits your patch better.

Toros Iteritas Alia is available on Noise Engineering's 10HP Alia oscillator platform. Buy an Alia module and use the included USB cable to connect to the Firmware Swap app and check out any other Alia firmware, free of charge, any time. More info can be found on the World of Alia page here.

Hotswappable overlays are coming in January, so you can easily panel your module to match your firmware, no assembly required.

Size and Power
10HP Eurorack
+12v:100mA
-12v: 15mA
Toros - perforated lizard - from Latin Torosaurus "foundation" with suffix -lus "small"

Iteritas - repetitiousness - from Latin itero "repeat" with suffix -tas "state of being"

Alia - supreme, from Latin alia

"Lizards reign supreme, as always"

What's in the box?

Module
Power cable
Micro USB cable

Noise Engineering no longer include screws with newly packaged modules, but Bulk screws are available for purchase.

Notes: TimeLine provides you with twelve different delay machines, each with extensive control over sonic character and feel. Tweak to your hearts content and save up to 200 presets of your favorite sounds. Go from crisp and clear, studio-quality digital delays all the way to the saturated and fluctuating sounds of tape delay machines.

Get warm and fuzzy analogue style repeats all the way to shimmery, sparkling, and crystalline ice delays. Top it all off with full MIDI implementation and a routable, 30-second stereo looper and you're on your way to delay bliss.

12 Different Delay Machines. TimeLine provides twelve studio-class, fully tweakable, and completely adjustable delay machines

Features

Hand crafted rotary algorithms faithfully deliver the signature, three-dimensional rotating speaker experience

Extensive control over rotating speaker mechanics and configuration

Four rotary adjustment and tone shaping knobs:

Fast Rotor Speed, Preamp Drive, Mic Distance, Horn Level.

Four "hidden" knobs for extensive tone tweaking:

Slow Rotor Speed, Cab Direction, Acceleration Time, +/- 6dB Boost/Cut.

Instantly alternate between a fast and slow rotor speed with the Fast/Slow footswitch

Selectable Cab Filter allows for an optimal experience in front of guitar amplifiers and full range systems

Stereo output, high impedance mono input

Expression pedal input with selectable control over any knob parameter

Connect our optional Favorite switch to save a favorite preset or use as an external speed switch

Fast/Slow and Bypass footswitches

Press and hold Fast/Slow footswitch for Rotary Brake

Selectable Bi-Amp mode splits bass rotor and treble horn signals to separate outputs

Ultra low noise, high performance 24-bit 96kHz A/D and D/A converters

110dB typical signal to noise

Premium analogue front end and output section

Super high performance DSP in a compact form factor

32-bit floating point processing

True Bypass (electromechanical relay switching)

Powered with a standard 9V center negative DC supply. 250mA minimum

Strong and lightweight mahogany anodized aluminum chassis

Crafted with love in the USA

Notes: Incredible value as always from the latest version of Arturia's Essential 88-key MIDI controller. Pads, faders, rotaries and a large LCD screen. Excellent integration with DAWs and the included Analog Lab V plugin.

Supplier's Notes:
Control your DAW, play with MIDI hardware, and get hands-on with your own style of music-making with KeyLab Essential mk3 88. This full-range keyboard controller removes barriers and makes creativity simple, with expressive semi-weighted keys, idea-sparking creative functions, and the most inspiring music software included as standard.

The streamlined piano range keyboard

Expand your musical horizons with a semi-weighted 88-note keyboard that removes barriers and makes your creative life easier. From studio to stage, DAW to MIDI hardware, KeyLab Essential 88 mk3 keeps things simple so you can focus on your music with full piano-range expressivity.

Your essential ingredients for creativity

KeyLab Essential provides an array of useful & intuitive controls that'll get the job done. Enjoy a comfy keybed, tactile faders/encoders/pads, and thoughtful layout that'll make sense for your setup. Enjoy a hands-on instrument experience balanced with software flexibility.

The best DAW integration

Get creative right out the box with KeyLab Essential's custom DAW scripts, bringing pre-mapped controls into your workflow with any major DAW. Not only that, but the KeyLab Essential controls work seamlessly with Analog Lab V, the included sound anthology plugin - letting you freely explore thousands of sounds, old and new.

Your musical workhorse

For when you want to get experimental, find a new sound, or just need a bit of extra inspiration, KeyLab Essential has a few tricks up its sleeve. Create fun ever-changing melodies with the Arpeggiator, weave rich chord voicings with Chord play, and always stay in key thanks to Scale mode.

What's new compared to the previous version?

A bigger display with 4 contextual buttons
5 dedicated DAW scripts, plus MCU & HUI protocols, for controlling any DAW
Enhanced integration with Arturia Software
Creative features: Scale mode, Chord Play, Arpeggiator (with presets), Hold function
2 Pad Banks (for finger drumming, clip launching, or User configuration)
Bigger software bundle (Analog Lab V, Ableton Live Lite, NI The Gentleman, UVI
Model D, Loopcloud & Melodics)
Multi-purpose pedal input (Sustain, Footswitch or Expression)
USB-C
Eco-designed

Included Software

You'll also get 6 titles giving you everything you need to make music your own way - here's

What's included:
Analog Lab V software with 2000 synth & keyboard sounds
Ableton Live Lite
UVI Model D & Native Instruments The Gentleman pianos
Loopcloud subscription
Melodics subscription

Box content
Quick Start
Registration card
USB Cable (C/A)

Notes: Saturation is a sound designer's best friend. As applying saturation to a sound can make it sound warm, rich and defined. But without any other processing the opposite can happen; making the sound harsh, destroyed and undefined. An often used technique in music production is to saturate specific parts of the spectrum, adding harmonics to enrich the sound but not lose its original quality.

Wyvern takes this technique and makes it a creative sound design tool. When deconstructed Wyvern is built out of a specific chain: Filter EQ, Saturation, VCA, Dual Filter, Dry/Wet Balance. Different combinations of these stages can be used for a variety of sound design and patch situations. And it is all in stereo, so you can apply it to your final mix and stereo signals with ease too!

The Filter EQ stage has a high-shelf, low-shelf and bell curve to boost or diminish parts of the spectrum. When the gain is set to a minimum the EQ curves turn into low-pass, high-pass and notch respectively. A Resonance control puts emphasis on a certain frequency, or it can be used to make Wyvern scream. This is then sent to a Saturation stage. The Drive control sets the amount of Saturation of one of the three

Saturation types

Soft clipping puts more emphasis on the third harmonic and compresses the sound.

Hard clipping puts emphasis on odd harmonics. Finally an Allpass distortion adds phase shifts and distortion. The Saturation stage also has a level control which can be used to decrease the gain after saturation is applied and can function as a unipolar VCA. The Saturation stage is also accompanied with a clip indicator led and a boost switch to scale input signal correctly or simply add more or less harmonics.

The Post-Saturation stage is a high-pass and low-pass combo. Allowing you to select a frequency band from the previous stages. Along with a balance control to adjust the balance between the dry and wet signal.

Whether you are looking to destroy your sound or go for subtle analogue warmth; Wyvern has got you covered. Even when not used for saturation alone. It can be a Stereo Tone Controller, EQ, Filter, VCA and Phaser, all and anything in between. Making it a very fun and powerful sound design tool!

Features

- Filter EQ with Low-shelf, High-shelf, Bell, Low-pass, High-pass and Notch curves.
- Resonance to add emphasis on a frequency or to make it scream.
- Soft clipping, Hard clipping and Allpass distortion for a variety of flavors.
- Boost switch and clip indicator led to set Saturation scale.
- Level and VCA to adjust level while Saturation amount remains the same.
- High-pass and Low-pass combo to select a part of the spectrum.
- Dry/wet control to dial in the right amount of processed signal.
- Gain with increased and adjustable center detent position.
- V/oct tracking with temperature compensation.

165mA @ +12V // 150mA @ -12V

Notes: *** Update February 2025- NKS Integration available with this product ***

Native Kontrol Standard (NKS) is a technical standard that connects plugins to hardware controllers with no setup required. The NKS ecosystem includes over 2,000 virtual instruments and plugin effects by over 250 acclaimed developers.

NKS enables users to load instruments and effects, tweak parameters, browse and manage presets with tangible controls, keeping creators' minds and hands on the music. No time is wasted creating, saving, and resetting controller parameter mappings.

Key features include:
Unified Control: NKS maps plugin parameters directly to hardware controls, allowing for hands-on adjustments without navigating computer menus.
Efficient Workflow: It streamlines browsing, loading, and editing presets, enabling producers to stay focused on creativity.
Broad Compatibility: Many third-party developers support NKS, offering a wide range of compatible sounds and effects.
For Our Products: This integration allows Akai and M-Audio compatible devices to fully utilize all NKS workflow features.

Here are some key points to take note of:

Current users will receive the software bundle once they register their device.

Both existing and new owners will receive the software bundle once their hardware is registered.


NKS Software Partnerships

For years, Native Instruments has partnered with world-class software manufacturers, including Arturia, Heavyocity, Korg, Output, Spitfire Audio, and many more, to bring thousands of instruments and effects plugins into the NKS ecosystem. Together with Native Instruments' own instruments and effects, this creates the most extensive database of any auto-mapped hardware controller ecosystem.

Until now, NKS hardware controllers were only available from Native Instruments, such as the Kontrol S-Series and Komplete Kontrol A-Series keyboard controllers.

NKS Hardware Partner Program [New]

At NAMM 2025, NI announced opening up NKS compatibility for third-party, non-NI hardware, allowing millions of performers and producers worldwide to enter the NKS ecosystem.

Supplier's notes:


A powerful MIDI 2.0 controller keyboard, Keystage offers unparalleled control, Polyphonic Aftertouch, MPE compatibility, and exceptional touch response. Enjoy instant OLED visual feedback, a powerful arpeggiator, chord modes, integrated audio outputs, and seamless Ableton Live & Korg Gadget integration. Lightweight & portable, Keystage integrates effortlessly with most modern DAWs and includes a powerful software bundle to amplify your musical journey.

Connect. Create. Perform.

Keystage is a groundbreaking MIDI 2.0 keyboard designed for both producers and stage performers. Pioneering the adoption of MIDI 2.0 Property Exchange, it combines aftertouch with powerful integration and control capabilities.

When inspiration strikes

Eliminate the hassles of lengthy MIDI mapping and missed moments of inspiration. With Keystage, when inspiration hits, your musical visions are captured swiftly and accurately.

As a pioneer in keyboard advancement, Keystage is the first to fully harness the capabilities of MIDI 2.0. Just connect it to compatible software, and watch as Keystage automatically maps parameters, displaying them on its sharp OLED displays. Every display is paired with its unique knob, ensuring you're always informed of the mapped parameters and their precise values.

Expressive creativity

A newly developed semi-weighted keybed provides an immersive playing experience. With polyphonic and channel aftertouch, alongside MPE (MIDI Polyphonic Expression), you can add depth and feel to your performances without your fingers leaving the keys.

An extraordinarily powerful arpeggiator offers features that go well beyond what any other MIDI Keyboard offers. A vast selection of patterns is complemented with unparalleled customisation options, including aftertouch-triggered ratchets, randomization, gating, and more.

In addition, chord mode benefits from a suite of 32 chord sets that can be used out-of-the-box, or customized and saved into any of the extra 32 user set slots. Each set can have one chord assigned to each note of an octave, and chords can even be replayed in different ways, including a strumming mode for realistic guitar-like playing.

Deep integration

Keystage offers immediate, seamless plug-and-play compatibility with most popular DAWs, giving hands-on control on your most important playback/transport controls.

From launch, Keystage supports: Ableton Live (Official Integration), Korg Gadget (Official Integration), Cakewalk, Cubase, Digital Performer, FL Studio, GarageBand, Logic, Pro Tools and Studio One.

On the road and in the studio

Keystage is not just an incredibly powerful MIDI controller. Equipped with direct stereo output, simply connect Keystage to your computer and directly link to the sound system without the need for additional gear that takes up valuable space.

Keystage also offers flexible customization options. You can modify settings directly through the menu or conveniently adjust them using the Korg Kontrol software on your computer.

Keystage includes an expansion plate that can be attached at two different angles, making it ideal for tablets and other devices.

Keystage x Ableton Live

Ableton Live is the industry-standard tool for live performance, thanks to its innovative dual Session/Arrangement view, smooth clip triggering, looping, and powerful production tools.

Keystage offers official integration with Live, putting both transport and device control at your fingertips.

Keystage detects the device currently active in Ableton Live, and automatically maps to the first 8 parameters. When switching devices, Keystage dynamically reconfigures itself for an uninterrupted experience, keeping you in the zone.

Both Ableton Live and Keystage are MPE-compatible, enabling enhanced flexibility and creative possibilities in your music. Live's powerful Drift synthesizer (available with version 11.3) leverages MPE to offer even more expressive capabilities.

Keystage comes bundled with Ableton Live 11 Lite as part of its software suite. Ableton Live 11 Lite is a beginner-friendly version of Live, providing many of the core features to help you kickstart your journey in music creation and performance.

MIDI 2.0

The future of music

MIDI 2.0 is one of the most exciting developments in electronic music production in decades and allows two-way MIDI conversations. Previously, MIDI 1.0 messages went in one direction: from a transmitter to a receiver. MIDI 2.0 is bi-directional and changes MIDI from a monologue to a dialogue.

Thanks to new MIDI-CI (Capability Inquiry) messages, MIDI 2.0 devices can talk to each other, and auto-configure themselves to work together.

Keystage retrieves information such as which Control Change (CC) parameters should be linked and the appropriate names to display for each parameter. This means that Keystage can talk with a wide range of MIDI 2.0 compatible devices and exchange information in both directions. This exciting feature extends not only to software plugins, but also to hardware devices.

MIDI 2.0 Property Exchange is compatible with traditional MIDI DIN cables, allowing Keystage to seamlessly integrate with existing devices. Furthermore, backwards compatibility is not an issue with Keystage: it can still communicate using MIDI 1.0 with devices that do not support MIDI 2.0.

Powerful software suite

Keystage comes bundled with an incredible software set that provides all the tools needed to take your music production to the next level:

Specifications

Keyboard

Polytouch* keyboard
Features velocity sensitivity, aftertouch, and polyphonic aftertouch
Velocity curves: 21 (-10 to +10)
Octave range: 7 (-3 to +3)

Controllers

Pitch bend wheel, modulation wheel, parameter control knobs × 8
VOLUME knob, SETTINGS button, WRITE button, EXIT button, SHIFT button, ARP button, CHORD button, VALUE ^/ buttons, VALUE dial, PAGE i/+ buttons, transport buttons, TEMPO button, OCTAVE i/+ buttons

Display
Main display: Organic EL (electro-luminescence) display
Sub display: Organic EL displays x 8

Scenes: 16

Arpeggiator: Arpeggio rhythm patterns: 20

Chord mode
Preset chord sets: 32
User chord sets: 32

I/O: USB port, MIDI (IN, OUT connectors), EXPRESSION jack, DAMPER jack

Audio output
AUDIO OUT (L/MONO, R): 6.3 mm TS phone jack (unbalanced)
Headphones: 6.3 mm stereo phone jack

Control inputs
Damper (half-damper supported)
Expression

USB: Type B, MIDI/audio interface
MIDI: 1 in/1 out
Audio: 2 ch out
Audio format: 44.1 kHz, 16-bit

Power
USB bus power or AC adapter (9 V DC, : Korg KA350, sold separately)
Power consumption: 5 V/500 mA or less (when powered via USB), 4w (when using an AC adapter)

Dimensions
Keystage-49: 814 × 234 × 82 mm

Included items: USB cable (Type A-Type B), expansion plate, Quick Start Guide

Notes: Really smart integration of macro controls for Eurorack, based on the original design by Emblematic Systems. Assign settings to eight CV outputs then morph with the crossfader or record movements to manage presets or set up complex real-time modulation. Can also operate as Catalyst Sequencer.

Supplier's Notes:
The Catalyst Controller is a macro controller with eight precision CV outputs and a responsive crossfader to morph between scenes. A scene is a snapshot of up to eight CV outputs, like a modular preset. Traverse a "pathway" composed of multiple scenes using the crossfader or an external CV signal, or immediately jump using the scene buttons. Record CV and slider movements, and play recordings back via a button or external trigger.

Each output has sub-millivolt precision and a maximum range of -5V to +10V. Channels have an adjustable morphing curve, can be quantized to common scales, restricted to a particular voltage range, or set to output gates.

Whether used as a CV preset manager, seamless transition generator, chord sequencer, CV recorder, or experimental CV playground, the Catalyst Controller puts control of your modular at your fingertips.

The Catalyst Controller can also turn into a Catalyst Sequencer! Hold down a special button combination to change between controller and sequencer modes. If you end up liking the Sequencer more, you can even remove the double-sided faceplate, flip it over, and re-install with the Sequencer artwork visible.

Based on the original Catalyst module from Emblematic Systems.

Specifications:

Smooth, responsive crossfade morphs between scenes
Eight output channels, each can be CV or Gate
Arrange scenes into pathways of up to 64 scenes
Smooth, responsive crossfader morphs from scene to scene along the pathway
Set slew/lag to limit how fast scenes can change
Adjustable Morph time per output
Control crossfading with an external CV
Record and playback up to 20 seconds of CV and crossfader motion
CV outputs can be set to -5V to +10V maximum, or limited to +/-5V, +5V, +3V, or +1V
CV outputs can be unquantized (sub-1mV resolution), or Quantized to common scales
Randomization of channel values/gates
Copy/paste
Based on the original Catalyst from Emblematic Systems

Pairs with: 4ms Catalyst Sequencer

Notes: A unique analogue percussion module, based on principles from the legendary 909 twisted into new sonic territory. Capable of everything from classic kicks and snares to more experimental hits and complex VCO effects.

Supplier's Notes:
A machine is born

The Machine began as a quest to create a rich-sounding eurorack snare drum synthesis module to complement the existing Mutant Drums. The project quickly became too large and costly to justify the module being capable only of snare drum sounds. So, the decision was made to learn from the architecture of the TR-909's snare and kick circuits, in order to develop a module capable of generating multiple forms of analogue percussion, and various other effects.

Like the other Mutant Drums, the Machine has its roots in classic analogue percussion synthesis. Even though it can create totally alien sounds, it still has the capability to deliver those classic 909 house snares and kicks if you want them. There are no microcontrollers in the Machine. The signals and waveforms are all generated by discrete components and ICs, for a distinctly analogue sound, and user experience.

Features

Microcontroller-free analogue percussion synthesis engine
Unique Inverter Core oscillators form the MEMBRANE. Each analogue oscillator has three waveforms to select from
Capable of synthesizing everything from heavy-hitting bassdrums to classic 909-style snares and other complex timbres
Modular design gives the Machine many auxiliary purposes, great for modular sound design of many varieties, and not just percussion
The SNAPPY section is comprised of a voltage controlled noise oscillator, for modelling the noisy part of drum timbres
Both MEMBRANE and SNAPPY elements have an external input for replacing the built-in sound sources, opening up many avenues of possibility
13 control voltage and audio inputs, for a fully modular drum experience
7 audio and CV/gate outputs for maximum integration with other modules
Dedicated outputs for each WAVE and NOISE oscillator mean you can use the Machine as a complex VCO in your system, when not synthesizing percussion
Waveform scanning feature generates complex timbres from analog waveforms
The MEMBRANE's waveforms can be scanned through automatically by the wavescanner's voltage controlled clock generator, or an external clock or VCO can be used
SCAN FREQ CV forms a unique form of timbre control, making the Machine act like a complex oscillator at its WAVES output
The ENABLE input allows you to gate the wavescanner on and off with a CV or gate signal

Technical specifications

Width: 29HP | Depth: 30mm
Current draw: +139mA, -115mA @ 12V

Notes: Really nice boutique analogue synth from JMT, based around a main oscillator with three sub signals, a frequency-synced resonant filter, noise source and three-speed random trigger.

Supplier's Notes:
DNVO-1 is a handmade, compact analog synthesizer from JMT Synth Its primary oscillator can be synced with three sub oscillators, each with a different range, as well as a noise source and wave generator. The latter source can be manipulated with the 3-speed random trigger for effective fluctuations within a single performance. The primary VCO is routed through a self-oscillating filter, which can sync with the VCO's frequency.

Notes: NightSky is a reverberant synthesis workstation and a powerful, hands on experimental sound design platform. Giving you real time continuous control of reverb pitch/processing rate/core size, harmonics, and even a synth-like resonant filter with multiple modulation waveshapes, plus a step sequencer with variable glide.

Deep and powerful sound manipulation with instant response knob- tweaking and no menu diving set a new standard in experimental reverb sound design. NightSky achieves some of it's most mind bending sounds by using a Variable Process Rate for it's reverb core, allowing you to simultaneously change the size of the reverb as well as the pitch. This pitch change can be completely smooth, or quantized to a variety of musical scales, it can also be sequenced.

Use Shimmer to shift the harmonic structure by selectable musical intervals. Add Glimmer to dynamically enhance the harmonic spectrum. Turn up Drive to generate saturated overdriven harmonics. Then sculpt the resulting signal with NightSky's synth-like variable-resonance low pass filter.

Features

Three selectable reverb types offer a wide variety of ambient textures

MOD section with various waveforms to modulate the reverb or tone filters

TONE section to sculpt the high and low EQ of the reverb

VOICE section to enhance the aural spectrum of the reverb

Adjustable SHIMMER for adding pitch shifting of up to +/- 1 octave to the reverb

GLIMMER dynamically enhances high or low frequency harmonics for synth-like textures

Pre or Post DRIVE to add saturated overdriven harmonics to the reverb

Adjustable reverb core size to increase or decrease the space for reflections

Independent REVERB and DRY level controls

Step sequencer for programming rhythmic pitch variations of the reverb

Access to 16 presets from the front panel and 300 presets via MIDI

High impedance ultra low-noise discrete Class A JFET preamp stereo inputs

Low impedance stereo outputs

Input Level switch allows for both instrument and line level signals

On, Favorite, and Infinite footswitches

Expression pedal input allows the connection of an expression pedal, MultiSwitch Plus, or 1/4" to MIDI cable

Full featured MIDI in/out supporting MIDI CCs, program changes, MIDI clock sync and more

USB jack for controlling via MIDI from a computer or for performing firmware updates

Analog dry path for a zero latency dry signal that is never converted to digital

Premium JFET analog front end

Ultra low noise, high performance 24-bit 96kHz A/D and D/A converters provide uncompromising audio quality

Super high performance SHARC DSP

32-bit floating point processing

20Hz to 20kHz frequency response

Audio Input Impedance: 1M Ohm

Audio Output Impedance: 100 Ohm

True Bypass (electromechanical relay switching) or selectable transparent Analog Buffered Bypass

Strong and lightweight anodized dark blue aluminum chassis

9V DC power supply included

Power requirements: maximum 9 volts DC center-negative, with a minimum of 300mA of current

Dimensions:

4.5" deep x 7" wide x 1.75" tall

114.3 mm deep x 177.3 mm wide x 44.5 mm tall

Designed and built in the USA

Notes: Way Back Machine

Step on Zelzah, play one chord, and you're instantly taken back to a world of classic phaser tones as they were always meant to sound, perfectly voiced, with tons of vibe. Vintage 4-stage and 6-stage phasing with controls that allow seamless transitions to vibrato, gorgeous flanging and chorus, and new sounds never heard before-all instantly musical with great tone all the way across every dial.

Two Effects At Once.

Zelzah is actually two different phasers, side by side in one pedal. Zelzah's 4-stage side gives you a wide array of classic tones ranging from phasing to vibrato and more, while the 6-stage side provides phasing, flanging, chorus, and all points in between. Dial in a chorus on one side and barber pole phaser on other, or a phaser on one side and tremolo on the other. Use the two sides independently or together in a variety of configurations. Zelzah may become the only modulation pedal you keep on your board.

Choose Your 4-Stage Phaser Sweep

Classic Sweep

The first Sweep mode is labelled "Classic" because this is the classic four stage phaser sweep we all know. In this Sweep mode, a single LFO with a warped triangle shape creates that familiar vintage sound.

Barber Sweep

Similar to the visual effect of a barber pole, the Barber sweep is a continuously rising or falling effect that is traditionally done with frequency shifters. In Zelzah, Strymon have used an arrangement of synchronized four stage phasers to produce the effect while maintaining the four stage sound.

Envelope Phaser

Set the Sweep switch to Env and you've got a whole new pedal under your feet. Now the phaser responds to your picking like an envelope filter/auto-wah would, with the phaser sweep being dynamically controlled by your input signal, creating harmonically complex and very funky sounds.

Six Stage Voice: Groundbreaking New Phaser Algorithm

The Voice knob on the six stage side simultaneously controls over 30 different parameters, all working in harmony for an inspiring musical experience.

Not only do you get thick, juicy, phasing with pure vintage vibe, but as you turn the Voice knob clockwise, the groundbreaking new modified all-pass structure expands the time response of the cascading all-pass filters seamlessly and continuously, adding spaciousness and airiness to the sound.

Explore a range of fresh musical tones that are not a mix of phasing and flanging, but actually something entirely new. Turn the Voice knob to the right for luxurious true flanger effects, and continue to the far end of the range for lush vintage chorus sounds. There are inspiring musical sounds at every point along the dial, and so many ways to make a sound that is truly yours.

Notes: The perfect pairing of a virtual analogue kick drum and side chain compressor. Designed as a single, easy-to-control module, Kickain revolutionizes your kick drum workflow by managing low-frequency artifacts and transients. The result? A cleaner, tighter mastering-standard mix featuring a truly powerful kick drum.

Spectral Compression

Kickain offers two spectral compressor modes that intelligently EQ the mix to fit around the triggered drum sound, adjusting continuously thousands of times a second. This optimizes the kick's loudness without intrusive 'pumping,' ensuring tracks sound tighter and richer in the low end.

Reverb

A 24-bit stereo drum room simulator, linked to the decay envelope, provides ambient reflections or explosive bass drops.

Notes: A creative approach to video synthesis courtesy of Critter & Guitari, the Eyesy generates real-time visuals to accompany a musical sound source. Deeper programming options allow you to control the graphics, trigger changes via MIDI or even code your own patterns.

Supplier's Notes:
Welcome to the world of the EYESY - Critter & Guitari's video synthesizer! The EYESY reacts to your music to create endlessly mesmerizing visuals. Simply plug it in and start creating. But don't be fooled by the simplicity of the EYESY, there are many features and goodies hidden inside. Whether you are creating live visuals, working on a music video, or want to program your own graphics, the EYESY will become an indispensable tool.

Modes

The EYESY comes with numerous pattern generators called modes.

Navigate the modes using buttons, and then tweak their visual appearance using five knobs. The modes respond to audio input in various ways; from smooth undulating patterns to rapid fire animations. The controls allow you to effect various elements of the patterns and colours. There is also a setting that allows the graphics to pile up in vibrant collages.

Save and Load

Store your current settings and screen grabs.

When you happen upon a setting that you like, press the scene save button to save it. This scene can now be recalled at a future time.

You can press the screen grab button to take a picture of the current frame, providing a quick way to generate interesting still images from your moving videos. Access all of your screen grabs from the browser-based interface.

MIDI Input

The EYESY's USB-MIDI & TRS-MIDI inputs offer a wide range of controllability.

Incoming MIDI Notes and Clock can change a mode's behaviour. The knobs can automated by sending MIDI controller messages from a sequencer or your favourite performance software. Program Change messages may also be sent to select your saved scenes.

Customise

Curate your EYESY for you.

You can add and remove the pattern generating modes to make the device as simple or complex as you like. The saved scenes are stored in a single file that can be saved and edited. All of the resources are managed through a simple-to-use web browser-based interface.

Coding

If you really want to go deep, you can also program your own modes for the EYESY.

Edit and create your own modes! The modes are all open source and based on an open platform. You can make changes to the modes and create new modes using the browser-based editor. Modes are written in the Python programming language.

Included items:

Power Supply:
Input: 100-240VAC @ 50/60Hz. Output: 9VDC, 1.3A, Center-positive polarity.
USB-WiFi Adapter (Ralink 5370 Chipset, 2.4GHz)

Included storage:
A microSD card holds the operating system and modes. There is ~4GB for available for mode storage.

Notes: KeyLab mk3 is a fully-featured MIDI controller that offers unparalleled control of software and hardware instruments.

Engineered for intermediate and advanced producers and experienced music makers alike, it fits perfectly into any setup with comprehensive DAW integration, advanced performance features and an enhanced keybed and interface; all integrated seamlessly within a robust wood and aluminum casing.

Whether sculpting a studio masterpiece or channeling the raw energy of a live performance, KeyLab mk3 removes every creative obstacle and offers intuitive, comprehensive controls that ensure musicians can find their expression.

Deep integration

The most advanced DAW integration of any controller. KeyLab mk3 can use MCU and HUI protocols as well as smart mapping technology. This, coupled with the seamless integration with Arturia software, and advanced user programs, makes KeyLab mk3 a must have tool for demanding musicians and producers.

Superior playability and finish

KeyLab mk3 combines excellent design with high-quality wood and aluminium components. The enhanced keyboard and robust construction ensures reliability and durability - meeting the demands of professional use.

Full creative control

Alongside its high quality, touch-sensitive controls, KeyLab mk3 is also fully customizable and easy to navigate with its full colour display. Adjust settings directly on the unit, or via the included software, for a personalized experience that adapts to all creative processes and performance styles.

Advanced creative features

KeyLab mk3 includes innovative tools like Scale, Arpeggiator, and Chord modes, enhancing your creative capabilities. These features allow musicians to explore new musical ideas and create advanced compositions effortlessly, making it a powerful ally in both the studio and live performances.

NEW enhanced keybed - Have greater control of synth and piano sounds with a full rework of keyboard balance, weighting and spring tension.

NEW visual interface - Have full control of settings, parameters and custom mappings with a 480x320px screen controllable with 8 contextual buttons.

NEW touch-sensitive potentiometers and faders - Have a greater degree of control with nine 360- rotary potentiometers and nine faders.

NEW creative features - Take your expression further with inspiring creative tools including a new Scale, Arpeggiator and Chord mode.

NEW pad capabilities - You can now harness a total of 4 Pad Banks of 12 pads for finger drumming, clip launching and endless mapping possibilities.

NEW software bundle - Kick-start your creative journey with pro software included: Analog Lab Pro, Mini V, Piano V, Augmented Strings, Rev PLATE-140, Ableton Live Lite, NI The Gentleman, Loopcloud & Melodics.

Included Software

Analog Lab Pro (2000+ sounds)
Mini V
Piano V
Augmented Strings
Rev PLATE-140
Ableton Live Lite
NI The Gentleman
2-month Loopcloud subscription
Melodics subscription with dozens of lessons

Box content

Quick Start
Registration card
USB Cable (C/A)

KeyLab 61 mk3

Dimensions

Weight/Size

Gift Box: 8.5 kg / 17.41lb
968 x 369 x 148 mm / 38.11x14.52x5.8 in

Product: 6.8 kg / 14.99 lb

873x278x74 mm
34.37x10.94x2.91 in

Notes: Legendary Vermona drum synthesis circuits get reimagined for Eurorack. The Bass/Drum reworks the kick and 'drum' circuits from the DRM-1 for extra modular flexibility, maintaining the powerful analogue sound.

Supplier's Notes:
With BASS|DRUM, Vermona have transferred the sonic foundation of the DRM1's KICK and DRUM instrument channels to the Eurorack format. They reworked the existing circuitry in key areas to optimize it for the modular context. The result is an Eurorack sound generator that clearly reveals its origins and at the same time surpasses them many times over.

The modulation possibilities of BASS|DRUM offer enormous flexibility. Many parameters like the pitch of the oscillator, the decay time and the integrated wave shaper can be controlled by external voltages. For example, you can create rhythmically alternating long and short or low and high kicks or tonal variations by modulating the waveform.

Use the DYNAMIC input to control the amount of force your trigger source applies to the internal circuitry of BASS|DRUM. This not only changes the volume, but also many different nuances of the sound.

Bass or drum? BASS|DRUM can do both, without compromise. If you need drum sounds that follow the tuning of your music, you'll find what you're looking for here. At the same time, the module serves as a full-featured audio oscillator that can be used to create bass lines or melodies.

From deep, powerful bass drums, toms and tom-toms to high-frequency pings and percussive chirps - no problem with BASS|DRUM! In combination with other modulation sources, this spectrum can be extended infinitely. The module is also an excellent oscillator for anything other than classic analog drum sounds.

Notes: KeyLab mk3 is a fully-featured MIDI controller that offers unparalleled control of software and hardware instruments.

Engineered for intermediate and advanced producers and experienced music makers alike, it fits perfectly into any setup with comprehensive DAW integration, advanced performance features and an enhanced keybed and interface; all integrated seamlessly within a robust wood and aluminum casing.

Whether sculpting a studio masterpiece or channeling the raw energy of a live performance, KeyLab mk3 removes every creative obstacle and offers intuitive, comprehensive controls that ensure musicians can find their expression.

Deep integration

The most advanced DAW integration of any controller. KeyLab mk3 can use MCU and HUI protocols as well as smart mapping technology. This, coupled with the seamless integration with Arturia software, and advanced user programs, makes KeyLab mk3 a must have tool for demanding musicians and producers.

Superior playability and finish

KeyLab mk3 combines excellent design with high-quality wood and aluminium components. The enhanced keyboard and robust construction ensures reliability and durability - meeting the demands of professional use.

Full creative control

Alongside its high quality, touch-sensitive controls, KeyLab mk3 is also fully customizable and easy to navigate with its full colour display. Adjust settings directly on the unit, or via the included software, for a personalized experience that adapts to all creative processes and performance styles.

Advanced creative features

KeyLab mk3 includes innovative tools like Scale, Arpeggiator, and Chord modes, enhancing your creative capabilities. These features allow musicians to explore new musical ideas and create advanced compositions effortlessly, making it a powerful ally in both the studio and live performances.

NEW enhanced keybed - Have greater control of synth and piano sounds with a full rework of keyboard balance, weighting and spring tension.

NEW visual interface - Have full control of settings, parameters and custom mappings with a 480x320px screen controllable with 8 contextual buttons.

NEW touch-sensitive potentiometers and faders - Have a greater degree of control with nine 360- rotary potentiometers and nine faders.

NEW creative features - Take your expression further with inspiring creative tools including a new Scale, Arpeggiator and Chord mode.

NEW pad capabilities - You can now harness a total of 4 Pad Banks of 12 pads for finger drumming, clip launching and endless mapping possibilities.

NEW software bundle - Kick-start your creative journey with pro software included: Analog Lab Pro, Mini V, Piano V, Augmented Strings, Rev PLATE-140, Ableton Live Lite, NI The Gentleman, Loopcloud & Melodics.

Included Software

Analog Lab Pro (2000+ sounds)
Mini V
Piano V
Augmented Strings
Rev PLATE-140
Ableton Live Lite
NI The Gentleman
2-month Loopcloud subscription
Melodics subscription with dozens of lessons

Box content

Quick Start
Registration card
USB Cable (C/A)

Dimensions (Weight/Size)

Gift Box:

7.9 kg/17.41 lb
882x369x148 mm / 34.72 x14.52x5.82 in

Product:

6.1 kg / 13.44 lb
30.98x11.02x2.83 in / 787x280x72 mm

Notes: This is an exact hardware replica of the Mutable Instruments Blades module.

This model uses the original "hard-to-find" opamps, but After Later have substituted V2164M with AS2164D. All of After Later's products use AS2164D and there should be no measurable change in behaviour.

Notes: In 2025, MOOER has announced that it will be set to release its latest multi-effects pedal, the GS1000 Intelligent Amp Profiling Processor, an augmented intelligent amp profiling processor. Built on MOOER's advanced third-generation digital platform, the GS1000 introduces groundbreaking MNRS 2.0 technology, allowing guitarists around the world to emulate their favorite gear with immense precision -specifically, for distortion pedals, preamps, amplifier heads, and cabinets.

With this innovation, guitarists can fully capture the essence of their favorite guitar gear without owning the physical hardware, enabling them to carry their favorite tones wherever they go. Users are even able to use third-party IRs for cabinets of their choice, further enhancing the flexibility of this feature.

It's unforgettable how much MOOER's multi-effects pedals have impressed audiences so far, primarily thanks to their robust tone libraries. However, even still, the GS1000 continues to build upon this with storage for up to 120 sampling profiles, along with continued integration with the MOOER Cloud app. Essentially, this cloud integration facilitates infinite upload and download possibilities, giving users access to a global community of shared tones, widely expanding the number of accessible tones. More still, the GS1000's previously mentioned third-party IR cabinet simulations support up to 2048 sample points, guaranteeing studio-grade tonal accuracy across the board.

Even more impressive for the price is how the GS1000 inherits the dual-chain effects architecture that made previous MOOER gear so versatile, making it suitable for highly complex usage scenarios. With over 350 factory effects models and a Sub-Patch preset grouping mode, the GS1000 makes it far simpler for users to make seamless transitions between tones, all while maintaining effect tails to guarantee seamless transitions. Additionally, the reintroduction of the innovative AI-driven EQ Master builds upon MOOER devices' previous capabilities, using intelligent adjustments in real-time to match the musical style of players to tones, while still allowing manual tweaks for precise control.

Impressively, the GS1000 also comes packed with a Groove Station module, consisting of a combination of drum machine and looper features - including 56 high-quality drum kits! It offers a 480-second phrase looper with infinite overdubs, automated detection, and synchronization capabilities, resulting in an intuitive platform for solo jamming, composition, and live loop-based performance. Overall, the Groove Station acts as an all-in-one suite for creating full arrangements, without having to depend on additional backing tracks or bandmates.

Visually and functionally, the GS1000 really stands out thanks to its sleek visual design and enhanced user experience. For example, it features a convenient 5-inch high-resolution touch screen, which is also paired with ambient lighting to add a visually stunning element to the pedal. As a result, the GS1000 is not only designed for convenient touch-based control but also as a standout centerpiece in any guitar rig.

In addition to this touchscreen control system, the GS1000 also provides expanded connectivity options, improving upon the already impressive flexibility of past pedals. Most notably, it supports connectivity with the MOOER F4 wireless footswitch, as well as the ability to control presets via external MIDI devices.

As is expected from MOOER these days, the GS1000 also excels when it comes to routing opportunities, going above and beyond the typical stereo 14" inputs and outputs that would be expected from other brands. Yes, it still includes such staples, but it also includes an XLR microphone input, alongside balanced TRS outputs for long-distance signal clarity. The configurable serial/parallel stereo effects loop enables seamless integration of external effects, and the addition of Bluetooth audio input and MIDI compatibility broadens its wide range of use cases for live and practice-based applications.

Furthermore, the pedal also serves as a professional audio solution thanks to its low-latency 2-in/2-out ASIO USB sound card. Supporting up to 192kHz sampling rates, the GS1000 makes recording and live streaming effortless, as it can easily be used with software DAWs, MOOER's editing software, as well as the USB-based MIDI control.

The GS1000 will be available in two versions - the standard white edition, which is powered by mains power, and the GS1000 Li version, which introduces a 7.4V 4750mAh lithium battery, chargeable through its power port. With this upgrade, users can enjoy up to six hours of continuous power-free playtime, making it ideal for practicing, busking, and generally performing on the go.

Overall, for fans of MOOER's previous amp simulation offerings, the GS1000 represents a natural evolution, building on everything that made its predecessors great while introducing cutting-edge features and expanded capabilities. Most importantly, MOOER has promised to continuously update its MOOER 4.0 tonal algorithms on the MOOER Cloud in line with the release, keeping things fresh for the company's dedicated user base.

Notes: The Sloer Stereo Ambient Reverb builds on our popular Slo lineup but adds two additional reverb algorithms, stereo width control, two additional modulation wave shapes, and the ability to control the sample rate. Now you can create immersive, lush, modulated, sleepy, and ambient soundscapes with more width and depth than ever before.

Save your favourite dreamscapes with three onboard presets by simultaneously pressing and holding down on the bypass and sustain switches. Scroll through them by simultaneously pressing and releasing bypass and sustain.

The five-way rotary dial allows five different reverb modes - the three you know and love from the Slo: Dark (Lower Octave), Rise (Ambient Swell), and Dream (Latching Pad); and the addition of two new modes: Rain (Delay Tap Diffusion) and Light (High Octave Shimmer). Secondary functions on the dial change between five different wave shapes for modulation on the reverb trail.

Combine deep modulation, long washy trails, and an immersive stereo field to experience Sloer.

5 reverb modes:

DARK - Add a lower octave to your reverb trail. Here you'll create deep and wide atmospheric sounds and channel nightmarish soundscapes. X knob sets the level of a -1 octave signal that feeds the reverb.

RISE - This is an auto-swell reverb for beautiful cinematic swells. Don't rush it. Let it breathe and gently wake up. X knob sets the amount of time it takes the reverb to swell in after a note is played. Set lower for shorter rise times and higher for longer rise times.

DREAM - Lush reverb with a latching pad function. Press the sustain switch to latch signal. Experiment with the X knob to add vibrato over the pad. Press sustain again and the pad will decrescendo according to where the decay knob is set. X knob sets the depth of vibrato applied to the reverb trail.

RAIN - Tappy and trippy, this program creates a unique effect with lower levels of diffusion allowing the reverb delay taps to audible create an echo-like effect within your reverb. Use the Xcontrol to set the amount of diffusion of the delay taps.

LIGHT - Bright and smooth reverb with an octave-up shimmer. Create a range of ethereal sounds with the X slider, keep it low for a smooth pad-like reverb or push it higher for a bright shimmer effect.

5 wave shapes

The Sloer also features five different wave shapes accessible by holding down bypass while switching the algorithm dial.

Sine - Smooth and even pitch up and down modulation.
Warp - Asymmetric pitch up modulation similar to a warped record.
Sink - Asymmetric pitch down modulation for sinking detune similar to a Bigsby.
Square - Symmetric pitch up and down modulation for stepped modulation.
Random - Uses sample and hold that picks new random values.

Momentary functions

Bypass: When the switch is in the off position, press and hold to temporarily activate the effect to add a moment of reverb texture. Releasing the switch turns the effect off, and fades it out.

Sustain: When pressed, the decay switch ramps up the reverb trail to maximum creating a long dreamy reverb trail, and then ramps back down to the decay knob setting when released. In the "Dream" algorithm, the sustain switch is latching. Press it once to capture and sustain the current reverb decay for extremely long pad-like sounds. Press it again to let the reverb trail taper off, based on the position of the decay knob.

Trails mode

The Sloer can run in trails or no trails mode. In trails mode, when you turn the pedal off, the reverb decay dies off naturally. In no trails mode, the decay is abruptly cut off when you turn the pedal off. To toggle between either mode, hold down the bypass switch for 1 second while applying power to the pedal. Unplug power and repeat to toggle to the other mode.

Preset spillover

When scrolling through presets, there is only preset spillover if the next preset is the same algorithm as the one preceding it. For example, if your red and green presets are both in Dream mode, switching from red to green will not cut your reverb trails.

Specs

The Sloer comes in a Lollipop Blue finish with light blue and off white ink featuring original artwork by Christi Du Toit OR a matte black finish with cream ink.
The die-cast enclosure's exact size is 4.79" x 3.62" x 2.25" including knobs.
Power requirements are 9VDC (100mA minimum).
The use of an isolated power supply is recommended for powering all Walrus Audio Pedals. Daisy chain power supplies are not recommended.
Power supply not included.

Notes: Erica Synths Bassline is fully analogue synth voice module for ultimate basslines and leads.

It features AS3340 VCO with three waveforms, a filter inspired by Erica Synths Acidbox and unique features - transistor based suboscillator and two BBD lines that emulate VCO detune creating a sound of massive polysynth from one oscillator.

Accent provides more expression to the bassline, by adding volume and opening the VCF slightly.

Notes: The D1 MKII is a feature-packed, high-fidelity all-in-one delay pedal with six algorithms for players to choose from: Digital, Mod, Vintage, Dual, Reverse, and Grain. The D1 can create inspirational delay trails ranging from dreamlike and bizarre, to rhythmic and clear, to warm and analogue sounding.

Program Controls:
Each program can be fully customized to your taste and playing style with the left encoder knob, which controls six parameters on all programs of the D1: Depth, Rate, Shape, Age, Tone, and Spread.

The Right encoder knob adjusts BPM, Swell, and Tap Division. BPM can also be set via the tap tempo switch or MIDI. Some programs will have additional options. See the manual for details.

Programs:
Digital - The Digital delay program offers a clean and crystal-clear delay that is perfect for rhythmic guitar parts where ultra-defined echoes are desired.

Mod - The Mod delay program has unique modulation LFOs applied to random repeats and run at multiple rates to create unpredictable pitch modulation. This results in unique sounding repeats perfect for warping minds and scattering trains of thought.

Vintage - The Vintage program allows for analogue tape delay-inspired tones to be achieved with complex filtering applied to the repeats. Use the tone knob at low settings for darker filtering and at higher settings to roll off the low end.

Dual - The Dual program employs two delays, one in each channel and both with different repeat subdivisions. The user has complete control over these subdivisions for both the L and the R channel, and can also choose to run their channel feedback in parallel, ping pong, or series. This effect can leave some jaw dropping trails, especially in stereo.

Reverse - The Reverse program reads the delay memory backward creating a unique delay repeat character known as a reverse delay. Select whether your repeats stay always reversed, or follow an analogue reverse feedback system where the repeats flip flop.

Grain - The Grain program can be as smooth, choppy, glitchy, or flowy as you want it to be, and for users who may want to try their hand at experimenting a little, this will be the perfect program for them to explore. The grain trails can be adjusted to short staccato sounding glitches, or opened up for full immersion. It's a whole new world, but the player is still firmly in control.

Presets:
The D1 can save up to 128 onboard presets, which can be held in a preset bank made accessible by tapping down on the bottom left and bottom middle knobs simultaneously. Presets 0-9 are divided into Banks A, B, and C. Select a bank while in the preset menu. Bank A will cycle through presets 0-2, Bank B will cycle through presets 3-5, and Bank C will cycle through presets 6-9. Presets 10-128 can be accessed through manual selection or MIDI.

Notes: Mojave is a granular sandstorm. Drawing its inspiration from vast swaths of desert in the American Southwest, Mojave is a live granular processor that uses microscopic bits of audio to create beautifully crafted sonic landscapes.

The core of Mojave's sound design palette is a unique set of melodic and rhythmic controls that presents each grain in a compositional context. Generate clock-synced granular arpeggios, or envelope your sound in rich harmonic swirls with the turn of a knob. All microsound settings can be easily accessed via individual knobs letting you tailor each grain, and effortlessly construct dunes of sound. Mojave is not exclusive to modular signals either; become the wind itself by using the onboard microphone to sift through and manipulate acoustic audio.

And, just like Nautilus, Mojave's internal settings can be configured via the USB drive and the Narwhal web app. Whether you are constructing pebbles or sandstone monuments, Mojave is the perfect balance between exploratory sound design and harmonious sublimity.

Live granular processor and stochastic event generator
Onboard high quality MEMS microphone
Configurable Dune CV/Gate output
Firmware updates & alternate firmware via the USB Drive
Based on the Daisy platform

Tech Specs

Width: 14HP
Depth: 28mm
Power Consumption: +12V= 167mA, -12V=13mA, +5V=0mA

Notes: Combining the power of multi-oscillator wavetable synthesis with the percussive detail of sampled sounds, Pianophonic is a powerful hybrid synth engine featuring 8 voices of polyphony. Not limited to Piano sounds, the voice architecture of Pianophonic is extremely versatile and easy to use with the essential controls laid bare on the front panel, and the most significant CV inputs and outputs provided for full integration within eurorack patches.

Taking its inspiration from the wavetable/sampler keyboards of the 90s, Pianophonic revisits a lean and mean approach to digital sound creation but instead with 24bit 48Khz quality and fingertip control of the parameters that really matter.

With a built in SD card and an online re-synthesise utility, allowing users to create their own sound banks, the possibilities for sound exploration are limitless.

Notes: The Yamaha MG16 Analogue Mixer. Road Tough. Studio Ready.

The Yamaha MG16 is part of the third generation of renowned MG Series mixers. These compact mixing desks focus on giving you high quality sound for a wide variety of mixing environments. The Yamaha MG16 has the same mic pre amps as their high-end pro mixers. The new MG Series provides serious quality with the reliability and performance capabilities the series is known for.

For more than a century, Yamaha has been building a legacy of superior craftsmanship and innovation exemplified in all of our products, from an unrivalled catalog of world-class musical instruments to touring-grade professional audio. Now in its third incarnation, the MG Series embodies this pursuit of design excellence, and incorporates some of the same technologies developed for use in high-end professional consoles, including studio-quality preamps, powerful digital processing, and a rugged, reliable construction.

With an intuitive, easy-to-use interface, the MG Series boasts an extensive lineup of compact mixing consoles with models ranging from six to twenty channels, suitable for a diverse range of users and applications. For installed, recording, or live music settings, the solid construction and flexible design of these consoles lets you shape your sound with confidence, continually delivering peak performance and a level of sound quality and reliability unrivalled in its class.