Notes: The LSwitch is a normally closed (NC) latching footswitch for use with various effect units or amplifiers that have an external footswitch jack. The onboard LED is supplied power by the switching circuitry on the host device; not all host units will necessarily power the LED properly, but the footswitch will work in spite of this.
Ring modulator based on the ARP 2600's 4014 ring mod - 8HP
Notes: Mobula is Delta Sound Labs' faithful take on the classic ARP 2600 ring modulator model 4014. This particular processor is renowned the world over for its clean sounding ring modulation effect. Due to its unconventional circuit design, where the positive and negative parts of the signal split between two two-quadrant multipliers, it achieves what is referred to as a four quadrant multiplication.
Built with a combination of modern closely matched and discrete transistors this super skiff friendly module is faithful to all of the original features, with the single addition of independent switching of input signal DC-blocking. This module is DC-coupled; meaning it will happily process both control voltages and audio signals at the flick of a switch. The unique electronic architecture leads to both significantly increased low frequency response and superior carrier suppression when compared to traditional transformer based ring modulation designs.
Notes: The EBS Microbass 3. We've all been there. Being forced by circumstances to rely on someone else's gear and left with that uneasy feeling it could turn into a disaster. With the new EBS Microbass 3, you can let go of that feeling and be confident you'll have your sound no matter the situation.
The EBS MicroBass 3 is a 2-channel preamp, built exclusively with premium components. It is engineered by EBS in Sweden with technologies from the famous HD360 and Fafner II amplifier designs. The preamp operates at a signal level equal to a professional mixing console (+/- 15V) which gives you plenty of headroom. The high signal level makes it suitable to use as a preamp in combination with any type of power amp.
Run the Clean and Drive channels in series or parallel. Use the dual balanced XLR-outputs to tap the signal post and pre EQ at the same time. If you run the Effects loop in stereo mode, the balanced outputs become a Left and Right output instead. With 10 Mohms input impedance, it handles any type of bass - passive, active or with piezo pickups.
The built-in tuner makes it easy to tune between songs without the need of an external device. The MicroBass 3 also carries an onboard compressor, similar to the one found on several EBS amplifiers, and several more features.
The analog EBS MicroBass 3 ensures your sound - every time.
Flexible overdrive/compression pedal designed in collaboration with Billy Sheehan
Notes: When Billy Sheehan first turned to EBS to create his signature pedal, he needed to capture the essence of his sound in a pedal to serve him when he could not bring his entire rig. It turned out so great it has been a significant part of his main setup ever since and served thousands of other bass players as well. Now it's time for the ultimate version!
"This pedal is a distillate of several important principles in the signal chain for bass. Compression, distortion, tone-shaping and blending all together", Billy said when EBS released his first signature pedal in 2013. The original concept is still the same, but with more features added along the way.
Since the pedal splits the signal into two parallel paths - one clean and one with distortion - it becomes as if running the sound through two different bass rigs at the same time. The two Clean and Drive Level controls decides how you set the mix and melt the paths together. For a tighter, more defined sound you can engage the built-in compressor. Threshold settings for the compressor can be adjusted inside.
A Phase Inverter switch brings back more low-end to the drive channel at times. The Boost footswitch kicks up the drive gain a notch when needed.
The new and major feature of the Ultimate version is the Hi or Lo Frequency Filter. This switch moves the whole frequency spectrum of the Tone filter up or down, to extend the capabilities of the pedal.
The Hi setting adds a whole new palette of distortion sounds that was not possible to create with previous versions of the pedal.
The individual Effect Loops for each channel can be used to colour the channels individually with external effects. The Clean Loop jack can also be used as a clean input if you have a bass that features dual outputs. It sounds great if you run the lows through the Clean Loop jack while the mids/highs go through the main input, which leaves the lows untouched and only the higher frequencies treated by the drive.
This version has inherited all the features from the Deluxe version (including the possibility to swap the drive chip without the need of soldering). But the palette of sounds you can create is expanded by the new Hi or Lo frequency filter to make it complete.
Notes: When your project requires a powerful performance with no sacrifice in quality, the Genelec 8030C active studio monitor is designed to exceed your expectations. The 8030C, introduced in 2017, even delivers 4 dB higher SPL and has a lower energy consumption than earlier models of 8030.
As strikingly stylish as it is sonically impressive, the 8030C features the rounded edges and colour-free, accurate reproduction of the rigid all-aluminium Minimum Diffraction Enclosure (MDE). Every element of the design is crafted to perfect your listening experience. Precise on- and off-axis frequency reproduction is courtesy of the Directivity Control Waveguide (DCW). Broad low-frequencies and high SPLs are delivered with a flow-optimised internal curved reflex tube and a maximised internal volume. And when you're finished, Genelec Intelligent Signal Sensing (ISS) circuitry detects when your system is no longer in use, placing it into an environmentally friendly, power-saving standby mode.
From professional studios to outside broadcast vehicles, the 8030C has been crafted to combine extraordinary power with absolute precision.
Notes: The AE modular Eurorack adapter frame allows to integrate AE modular modules into Eurorack systems. It is basically an empty Eurorack-sized frame that can take up to 12 units of AE modules where two units are occupied by the mandatory MASTER module. Via the MASTER module the frame is powered from the Eurorack bus.
The product includes:
- The mounting frame with screws for mounting the AE modules
- The ribbon cable for Eurorack bus connection
- The bus cable
… Read more
Artikel 1 bis 50 von 75 auf Seite 1 von 2 anzeigen