Notes: 2HP narrow version of the A-180 multiples module. It is a passive signal splitter suitable for audio or CVs. Two sets of four jacks are interconnected, by placing a solder bridge you can connect all eight jacks.

Dimensions
2 HP
18 mm deep

Current Draw
Module does not draw current

Tags: Multiple module | Utility module

~~MRP:$36.50~~ SAVE 14%
out of stock $31.39

People also bought...

Doepfer A-180-4 Quad Buffer Multiple Module (utility/quad/multiple module)

Doepfer

Cat: 714707 Rel: 22 Jan 19 • View all Synth modules

Quad buffer multiple module - 4HP

Notes: Module A-180-4 is a fourfold CV buffer. Buffers are required if the control voltage coming from a CV source shows a voltage drop in case of changing loads or due to other reasons a buffering is required.

For the lower three units the input is normalled to the output of the above unit. That way the module can work as 1-in-4 buffered multiple provided that no signals are applied to the inputs of the three lower units.

Typical applications:

- Buffering the outputs of voltage controlled switches (e.g. A-150-1, A-150-8, A-151, A-152). Comment: in case of bidirectional switches it's not possible to integrate the buffers into the switching module because the direction is not known (i.e. which terminal of the switch is working as input and which as output). All electronic switches suffer from a small residual restistance that may cause a small voltage drop without buffering. This may become a problem especially when VCOs are controlled by the switched voltages.
- Buffering of CV interfaces, quantizers, slew limiter, S&H/T&H, sequencer etc. when VCOs are controlled by the CV (provided that the module in question does not feature a buffered output)
- Buffered multiple (similar to A-180-3)

Tags: Utility module

~~$43.34~~ SAVE 20%
out of stock $34.66

Doepfer A-100BUSV6 Bus Board With 22 Boxed Pin Headers & 4 Connection Cables

People also bought...

Doepfer A-100BUSV6 Bus Board With 22 Boxed Pin Headers & 4 Connection Cables (bus board)

Doepfer

Cat: 763100 Rel: 31 Jan 20 • View all Synth Module Accessories

Notes: Bus board to connect 14 modules

An assembled and tested bus board, 22 sockets, e.g. for customers who want to built their own case and need a bus board for A-100 modules, includes cables for connection to +/-12V power supply (4 wires with flat connectors on both ends, length about 30cm), but no mechanical parts (e.g. screws, spacers, nuts, washers).

In the new version of the A-100 bus board (labeled Version 6 / 2019) boxed pin headers are used which are equipped with a reverse protection (gap for the "nose" of the socket of the bus cable). When the bus cable coming from the module is connected to the boxed header in question the "nose" has to point to the right. The polarity of the cable is correct if the red wire of the bus cable then points to the bottom (to the continuous line labeled"RED WIRE" on the pc board). If this is not the case please do not connect the module to the bus board ! Otherwise both the module and the power supply (A-100PSU3) may be damaged ! In that case please contact the manufacturer of the module and ask for a suitable bus cable with the correct polarity of the connector.

The bus cables of original A-100 modules manufactured by Doepfer are equipped with suitable bus cables since 2012. Only for older A-100 modules manufactured before 2012 it may happen that the polarity of the 16 pin female connector of the bus cable is wrong (nose points to the left when red wire points to the bottom). This is because in the past unboxed pin headers were used and the position of the "nose" did not matter. In such a case please contact Doepfer or one of their dealers and order a suitable bus cable.

Tags: Eurorack bus boards

~~MRP:$40.67~~ SAVE 11%
1 in stock $36.24

People also bought...

Doepfer A-186-1 Gate & Trigger Combiner & Rectifier Module (synth module)

Doepfer

Cat: 751765 Rel: 23 Oct 19 • View all Synth modules

Gate/trigger combiner - 4HP

Notes: Module A-186-1 is a very simple, passive unit that combines up to 7 gate, trigger or analog signals by or-wiring.

Function:

- If all seven inputs are low or open the output is low
- If one or more of the seven inputs is "high" the output turns high

Applications:

- Combination ("or"-wiring) of gate and/or trigger signals (e.g. from LFOs, sequencers, keyboards, Midi-to-CV interfaces, ribbon controller, theremin, trigger delays or any other source of gate/trigger signals
- Maximum extractor for analog voltages: at the output the maximum voltage (minus ~ 0.7V because of the diodes) appears, similar function as the maximum output of the A-172 Maximum/Minimum Selector module, e.g. for simple waveshaping
- Simple half-wave rectifier

out of stock $40.67

People also bought...

Doepfer A-183-1 Passive Dual Attenuator Module (silver) (dual/stereo/attenuator synth module)

Doepfer

Cat: 751728 Rel: 23 Oct 19 • View all Synth modules

Dual passive attenuator - 4HP

Notes: Module A-183-1 is a simple passive dual attenuator. Passive means, that each unit is made of two sockets and a 50k linear potentiometer only. There are no active parts like amplifiers or buffers and no power supply is required.

This is how the A-183-1 works: At the output socket appears the attenuated input signal, i.e. zero level at the fully CCW position and max. level and the fully CW position.

Applications:

Adjustable level of CV or audio signals to control other modules that do not have attenuators (e.g. Dual VCA A-132-1, Quantizer A-156, CV-to-Midi interface A-192 and modules of other manufacturers).

Tags: Attenuator module

out of stock $41.71

People also bought...

Doepfer A-100BUS4 Bus Board With 4 Connection Cables (bus board)

Doepfer

Cat: 755436 Rel: 12 Nov 19 • View all Synth Module Accessories

Passive Eurorack bus board

Notes: The A-100BUS from Doepfer is a simple passive busboard for use with Eurorack modules. It features 14 power headers along with three sets of spade terminals for connection to power supplies such as the Doepfer PSU3 and daisy-chaining with other A-100 bus boards.

out of stock $42.76

People also bought...

Doepfer A-180-2v Passive Multiple vintage Edition Module (black) (dual/stereo/multiple synth module)

Doepfer

Cat: 751717 Rel: 23 Oct 19 • View all Synth modules

Passive multi-port distributor - 2HP

Tags: Multiple module

1 in stock $43.79

Click for better price!

or call +44 20 7424 1960
quote 751717

People also bought...

Doepfer A-181 Multiples 2 Module (synth module)

Doepfer

Cat: 751722 Rel: 23 Oct 19 • View all Synth modules

Two multiples with one 1/4 jack socket & two 3.5mm jack sockets each

Notes: Doepfer's A-181 Multiples 2 is a simple multiple and cable format converter, suitable for translating 1/4" signals to 1/8" and vice versa. The upper mult is wired for monophonic signals, while the lower mult features a 1/4" stereo connector which offers direct 1/8" connection to the tip and ring, respectively, allowing use as a stereo splitter or dual 1/8" to stereo 1/4" converter.

Tags: Multiple module

out of stock $43.79

Doepfer A-100MNT Mini Power Supply & Bus Board For Eurorack

People also bought...

Doepfer A-100MNT Mini Power Supply & Bus Board For Eurorack (power supply/bus board)

Doepfer

Cat: 755435 Rel: 12 Nov 19 • View all Synth Module Accessories

Miniature PSU/bus board

Notes: The A-100 MNT (Mini power supply/bus) is composed of a miniature power supply and system bus, with connectors for four modules. It's designed to be used with a small set-up of just a few modules, in your own custom-designed case. The idea is that then you can use individual A-100 modules - for instance the filters, the filterbank, frequency shifter, sampler, MIDI interface, etc. - as free-standing pieces of equipment, which can easily be integrated with your other instruments or recording equipment.

The power supply provides the usual A-100 system requirements of +12 V and -12 V, and an additional +5 V supply, for the few modules (for instance A-190, A-191) which need it. The maximum current loading capacity totals 100 mA for +/- 12 V and/or 50 mA for the +5 V supply.

The system bus provides connections for four System A-100 modules. As well as the power supply, it also carries "INT.CV" and "INT.GATE" connections (see A-100 manual, main introduction, chapter 3, 'The A-100 signal flow'.).

The A-100 MNT is supplied as standard with an external power supply, which has to be connected to the socket on the MNT's circuit board.

out of stock $46.91

People also bought...

Doepfer A-183-2 Offset Generator/Attenuator/Polarizer Module (attenuator/CV modulation/polarizer module)

Doepfer

Cat: 751731 Rel: 23 Oct 19 • View all Synth modules

Offset generator, attenuator & polarizer module - 4HP

Notes: Module A-183-2 is a voltage offset generator combined with an attenuator/polarizer.

This is how the A-183-2 works: At the two output sockets (simply two connected sockets) appears a DC voltage that is adjusted with the Offset control in the range 0...+5V or -5V...+5V. An internal jumper is used to select the offset range (0...+5V or -5V...+5V). Other ranges are possible by changing a resistor on the pc board (e.g. 0...+10V or -10V...+10V). The DC voltage generated by the Offset control is overlaid by the attenuated voltage that is fed to the In socket. The function of the attenuator control can be set to Attenuator or Polarizer by means of a toggle switch. When the switch is in the Attenuator position the control works as an usual attenuator, i.e. zero level at the fully CCW position and max. level and the fully CW position. When the switch is in the Polarizer position the control works as a polarizer, i.e. zero level appears at the centre position. Right from the centre position the In signal is added to the offset voltage, left from the centre position the In signal is subtracted from the offset voltage. In other words: at the fully CW position the non-inverted In signal is added with the full level to the offset voltage, at the fully CCW position the inverted In signal is added with the full level to the offset voltage.

The amplification range for the input is about 0...+1 in the attenuator mode, and -1...+1 in the polarizer mode. The amplification range can be modified by replacing a resistor by another value.

Applications:

Generation of adjustable DC voltages overlaid by control voltages with adjustable level and polarity to control other modules that do not have attenuators or offset controls, e.g. Sampler A-112 (mainly for the wavetable mode), dual VCA A-132-1, VCLFO A-147-2 for waveshaping and ring modulator applications, Quantizer A-156, Theremin A-178, CV-to-Midi interface A-192 and modules of other manufacturers).

Tags: Attenuator module | CV modulation module

~~MRP:$57.36~~ SAVE 18%
out of stock $47.28

People also bought...

Doepfer A-126-2exp Voltage Controlled Frequency Shifter II - Expansion Module (silver) (expander synth module)

Doepfer

Cat: 852803 Rel: 04 Feb 22 • View all Synth modules

An expander for the A-126-2 Voltage Controlled Frequency Shifter.

Notes: The Doepfer A-126-2exp is an expander for the A-126-2 Voltage Controlled Frequency Shifter.

It adds two outputs from the Dome filter (+45 and -45 degrees) as well as separate outputs from the ring modulators 1 and 2, and from the internal envelope generator. Furthermore, it offers dedicated outputs for Up and Down Shift, allowing the module to be patched in stereo.

*Note: The expander can only be used in conjunction with the module A-126-2.

HP : 2

Tags: Expander module

1 in stock $49.79

Click for better price!

or call +44 20 7424 1960
quote 852803

People also bought...

Doepfer A-138u 2x3 Dual Micro Mixer Module (synth module)

Doepfer

Cat: 716960 Rel: 29 Jan 19 • View all Synth modules

Eurorack mixer for audio signals or control voltages - 4HP

Notes: Module A-138u is a simple, low-cost mixer with two units. Each unit is equipped with three inputs and one output. The upper unit has for each input a trimming potentiometer available that works as attenuator and allows to adjust the amplification in the range 0...+1. In the lower unit only the third input is equipped with such an attenuator. The factory setting is amplification = 1 for all inputs.

The output of the upper unit is normalled to the first input of the lower unit. That way the module can be used also as a mixer with five inputs: for this the inputs 1, 2 and 3 of the upper unit and the inputs 2 and 3 of the lower unit are used. The sum output for all five signals is then the output of the lower unit. As soon as a plug is inserted into input 1 of the lower unit the module becomes a dual 3-in-1 mixer again.

Inputs and Outputs are DC-coupled, i.e. audio and control signals can be mixed.

Application examples:

Mixer for audio signals, e.g. three VCOs preceding a VCF, when the amplifications are adjusted slightly different no signal extinction occurs during the beat of the VCOs

Mixer for control voltages (e.g. LFOs, envelope generators, random voltages)

out of stock $50.04

People also bought...

Doepfer A-162 Dual Trigger Delay Module (B-STOCK) (synth module)

Doepfer

Cat: 772513 Rel: 10 Sep 19 • View all Synth modules

B-STOCK: Item refurbished, repaired and in perfect working order.

Notes: ***B-STOCK: Item refurbished, repaired and in perfect working order.***

Module A-162 contains two identical circuits that generate a trigger signal with adjustable delay and length from an incoming rectangle signal (e.g. gate, trigger, rectangle output of an LFO or VCO). The rising edge of the incoming signal is used to trigger the new trigger signal. This module makes it possible to delay the onset of a trigger pulse, and also change its length.

On each of the two units, two controls can alter the onset time and duration of triggers, from about 2 ms up to more than 10 seconds. A control LED shows the generated signal.

Tags: Delay module

out of stock $50.37

People also bought...

Doepfer A-139-2 Stereo Headphone Amplifier Module (external/utility synth module)

Doepfer

Cat: 738616 Rel: 10 Jul 19 • View all Synth modules

Stereo headphone amplifier - 6HP

Notes: The A-139-2 is a headphone amplifier module with two mono inputs and a stereo headphone output. It can be used for driving small loudspeakers, LED strips, small magnets etc.

- Two-channel headphone amplifier
- Two audio inputs with level controls
- Input 1 is normalled to Input 2
- Common loudness/master level control
- Headphone output (stereo 1/4" jack socket)
- Max. output power ~ 2 W per channel (@ 8 Ohm load)
- DC coupled inputs and outputs (i.e. also useful for other applications like small loudspeakers, lamps, LEDs, magnets, motors - provided that the power is sufficient)

Tags: Headphone amplifier module

~~MRP:$61.53~~ SAVE 17%
out of stock $51.06

People also bought...

Doepfer A-138b 4-Channel Mixer Logarithmic Module (silver) (mixer/quad synth module)

Doepfer

Cat: 577776 Rel: 29 Nov 17 • View all Synth modules

Four channel mixer module - 8HP

Notes: Module A-138 is a four channel mixer, which can be used with either control voltages or audio signals. Each of the four inputs has an attenuator, and there's a master attenuator, so that the mixer can be used at the end of the audio chain, i.e. it can be used to interface directly with an external mixer, amplifier, etc.

The A-138b has potentiometers with logarithmic response, so is especially suitable for audio signal mixing.

Tags: Mixer module

~~MRP:$58.40~~ SAVE 12%
out of stock $51.12

People also bought...

Doepfer A-138a Linear Mixer Module (silver) (mixer/quad synth module)

Doepfer

Cat: 577762 Rel: 06 Jun 19 • View all Synth modules

4 channel mixer - 8HP

Notes: Module A-138 is a four channel mixer, which can be used with either control voltages or audio signals. Each of the four inputs has an attenuator, and there's a master attenuator, so that the mixer can be used at the end of the audio chain - i.e. it can be used to interface directly with an external mixer, amplifier, etc.

The A-138a version features potentiometers with linear response, so especially suitable for control voltage mixing.

Tags: Mixer module

~~MRP:$58.40~~ SAVE 12%
out of stock $51.58

People also bought...

Doepfer A-180-3 Dual Buffered Multiple Module (silver) (dual/stereo/multiple synth module)

Doepfer

Cat: 751720 Rel: 23 Oct 19 • View all Synth modules

Dual buffered 1-in-3 multiple module - 4HP

Notes: Module A-180-3 is a dual buffered 1-in-3 multiple. The signal applied to the input socket appears as a buffered signal at the three output sockets. Each output has its own buffer, i.e. the three output sockets are not simply connected to each other. The lower output of the upper unit is normalled in the factory to the input of the lower unit. That way the module works as a single 1-in-6 buffered multiple provided that no signal is applied to the input of the lower unit. But it's also possible to pick-up the bus CV and normalize the input socket of the lower unit to the bus CV.

Application: copying/buffering of CV, gate and audio signals.

Tags: Multiple module

out of stock $52.13

People also bought...

Doepfer A-183-9 Quad USB Power Supply Module (power/quad/utility synth module)

Doepfer

Cat: 711015 Rel: 29 Nov 18 • View all Synth modules

Simple power supply for up to four devices - 2HP

Notes: Module A-183-9 is a simple power supply for up to four devices which can be powered via USB (e.g. keyboards, smartphones). An LED shows is the +5V are present.

The module has no USB function but provides only the +5V supply for USB devices.

A control LED shows if the +5V are present.

Note: The module requires an A-100 case with built in power supply A-100PSU3. Only this A-100 supply has the required +5V available. We do not recommend the usage of an older A-100 case with A-100PSU2 as this would require the +5V adapter A-100AD5 and the max. current would be limited to 100mA.

Tags: Power module

5 in stock $52.13

Click for better price!

or call +44 20 7424 1960
quote 711015

Artikel 1 bis 50 von 302 auf Seite 1 von 7 anzeigen

1 2 3 4 5 6 7 »

2 3 4 5 6 7

Options

Display

Items per page:
Show tracks:
Hide played by

Stock

Show out of stock titles

Misc

Save sort order

Hilfe & Information

Juno-Angebot

Juno Daily Coming soon Geschenkgutscheine Classics Charts erstellen Represses Vollständige Labelliste Top-Labels

Mein Juno

My artists and labels Meine „Wieder auf Lager”-Benachrichtigungen Mein Konto Mein Wunschzettel Meine Charts Meine „Neuerscheinungen”-Benachrichtigungen Meine Bestellhistorie Meine „In Kürze”-Benachrichtigungen

100% Sicheres Einkaufen

DJ Mag Best Of British

Best Music Store: 5 time winners

All image and audio content is used by permission of the copyright holders or their agents, and/or according to fair dealing as per the UK Copyright, Designs and Patents Act 1988.

We'd like to know what you think of Juno's website. Please send us your comments and suggestions via our feedback page.

This website uses cookies

We use cookies to personalise content and ads, to provide social media features and to analyse our traffic. We also share information about your use of our site with our social media, advertising and analytics partners who may combine it with other information that you've provided to them or that they've collected from your use of their services.

Necessary

Statistics

Marketing

Cart subtotal:

View cart

Suchergebnisse: Dance Music

Filter

My search

Saved Searches

Stock

Coming Soon

Type

Equipment

Format

Release Date

Brand

Featured

Price

Tags

Hilfe & Information

Juno-Angebot

Mein Juno

100% Sicheres Einkaufen

DJ Mag Best Of British

This website uses cookies

Cart subtotal: