Nu-X

Notes: The Reissue series 63 Diamond pedal offers players a range of overdrive that emulates the sound of a classic British 30-watt class-A valve amplifier, much-revered by guitarists since 1959 for its tonally rich clean and crunchy overdrive sound. The styling of the 63 Overdrive is a nod towards the cabinet that stood behind the bands of the British blues invasion and rock bands of the 1970's through to present day guitar bands. Volume and Master controls let you dial in the drive, with a tone Cut control just like the real amplifier. A Top boost switch introduces additional bite and was a later addition to the design in 1963, which is where this pedal gets its name. Invoking 60's British cool in a single pedal was never this easy before.

Batteries: 9V PP3 (supplied)
Power supply: Optional 9Vdc 300mA regulated (not supplied)
Controls: Volume, Master, Cut, Top Boost & foot switch
Input impedance: 1M Ohms
Output impedance: 10k Ohms
Dimensions: 121 x 77 x 48mm
Weight: 230g

In the Box

63 Diamond overdrive pedal
9V PP3 battery

Notes: The Reissue series 6ixty 5ive overdrive puts the sound of the famous1960s black panel amplifiers right at your feet. Emulating the drive of these classic models gives a range of tones from just over-the-edge all the way to burning tube overdrive whilst retaining the guitar's natural voice and clearly defined edge. The all analogue circuit has a Gain control to adjust the amount of drive and the resulting output is balanced by the Level control. A Trim pot on the rear of the pedal further controls the saturation of the gain stage, bringing natural sounding compression and sustain into play. Bass and Treble controls provide tone shaping as you would find on a classic amplifier. Use as an "always on" drive pedal or switch in for a gain boost with a classic edge whenever the mood needs it.

Classic 1960's black panel amplifier tones
Level and Gain with Trim pot for drive & saturation settings
Bass & Treble EQ controls
True bypass switching
Batteries9V PP3 (supplied)
Power supply: Optional 9Vdc 300mA regulated (not supplied)
Controls: Level, Gain, Bass, Treble, Trim & foot switch
Input impedance: 1M Ohms
Output impedance: 10k Ohms
Dimensions: 121 x 77 x 48mm
Weight: 230g

In the box

The box for this item contains :

Reissue series 6ixty 5ive overdrive pedal
9V PP3 battery

Notes: Mains switch-mode power adaptor to operate 9Vdc effect pedals up to 500mA (polarity is pin-negative)

Suitable for NuX effect pedals and most other brands

The box for this item contains :

9Vdc 500mA adaptor

Specifications:
Power supply: 100-240Vac, 50/60Hz
Output voltage: 9Vdc
Output current max.: 500mA
Polarity: Pin-negative
Dimensions: 90 x 80 x 60mm
Connector: DC jack 5.5 x 2.1mm
Weight: 90g

Notes: Amp Academy Pedal

The Amp Academy is a complete valve amp modelling rig in a compact stomp box format. 3 storable scenes with 2 channels, selectable from 6 separate classic amplifier models. Each patch has Gain, Master and Boost for overdriven tones and 3-band EQ + Presence control. As with a real professional tube amp, there is an effects loop and internal rever effect. The addition of a noise gate helps to keep everything silent when no notes are played. Balanced or unbalanced outputs give flexible options for live performances via FRFR speakers, mixing console, or even for direct recording. All settings are fully editable via USB using the proprietary Amp Academy software and even self-made or third party IRs can be loaded for custom amp modelling. Next time you are carrying your heavy valve amplifier around, consider this incredibly flexible and pocket-sized alternative.

Power supply: 9Vdc, 100mA (min) pin-negative (not included)
Controls: Gain, Master, Boost, NR, Bass, Middle, Treble, Presence
Connections: Guitar in/out (6.3mm), Loop (6.3mm TRS), Aux (3.5mm), DI (XLR)
Dimensions: 115 x 105 x 58mm
Weight: 440g

Notes: Damp is the name given to this miniature digital reverb pedal to describe the immersive sound image provided by its 3 inbuilt reverb models. A choice of Spring, Plate or Hall reverberation types can be selected by the illuminated push button at the top of the pedal. Holding this button down during power-up selects between mono output or stereo output, which requires a stereo jack lead. Three rotary controls adjust Decay, Level and Tone settings as required. Pressing the footswitch activates or deactivates the effect, whilst holding this pedal enables a secondary effect - Shimmer in Plate mode or Freeze in Spring or Hall modes. The Damp pedal is versatile enough to cover a wide range of reverb styles with a minimal footprint on guitarists' pedalboards or for patching into an effects loop for other instruments or even vocals.

Power supply: 9Vdc (DC5521 connector, negative centre, adaptor not supplied)
Controls: Decay, Level, Tone and 3 reverb modes switch
Dimensions: 94 x 53 x 51mm
Weight: 175g

In the box

The box for this item contains :

Damp digital reverb pedal

Notes: Great value from this intuitive percussion pad, featuring eight touch-sensitive zones and built-in drum and percussion sounds. Hook up kick and hi-hat pedals if you like, or just jam with a pair of sticks and headphones.

Supplier's Notes:
DP-2000 is a digital percussion pad with 8 touch sensitive zones and a huge library of internal sounds.

A USB-to-PC/Mac interface enables integration with a software recording suite as a trigger controller and sound source. Sounds from the flagship DM-8 kit are stored internally, along with additional world percussion instrument samples and the option to add user samples from a USB flash drive. Sounds are assignable to pads and adjusted using the intuitive user interface and control surface, and each pad has a dynamic indicator which varies in brightness to mirror the playing dynamics. Dedicated MIDI in and out connections mean that the DP-2000 can expand a live playing setup or operate from hardware sequencers and other MIDI controllers. In addition to tuning and dynamics control, dual-engine DSP effects can be applied to each sound and tailored to suit each sound. If performance space is very limited, inputs for a hi-hat pedal, kick pad and an additional trigger can turn the DP-2000 into a fully playable super-compact e-drum kit. Add the possibility of music playback from USB flash drive and comprehensive input and output options, the DP-2000 is as much at home as a standalone instrument or as an expansion to an existing drum or percussion kit.

Add hi-hat & kick triggers for a full e-drum kit
USB-C Bluetooth adaptor
USB interface to PC/Mac
Importable WAV files for custom sounds
Power supply: 9Vdc, 500mA (tip-negative) adaptor supplied
Inputs: Aux input, trigger, hi-hat, kick, MIDI 5-pin DIN, USB-C (U-Disk)
Outputs: Headphones (3.5mm), L+R output (6.3mm), MIDI, USB-B (PC/Mac)
Dimensions: 408 x 314 x 62mm
Weight: 2.8kg

In the box

The box for this item contains:

DP-2000 digital percussion pad
DC power adaptor
USB-C Bluetooth adapter

Notes: A set of 5 durable plastic caps for foot switches in different colours. Suitable for use with NU-X effect units.

*** Please note: the pedalboard is not included, it is shown for demonstration purposes only. ***

In the Box

5 x colourful pedal toppers

Notes: Evolving from the popular Metal Core Deluxe pedal, the mkII version now has 3 selectable amplifier models based on much-revered high gain valve amplifiers. Now with an additional Middle control, the 3-band EQ pairs with Gain and Master to offer a full completement of real amplifier controls, with settings stored into each of the 3 amp models for fast recall. Metal Core Deluxe mkII goes a step further to include IR cabinet simulation, meaning that it can be used directly into a full-range PA system, or without IR simulation into the front of a guitar amplifier as a hard-edged drive pedal. Whichever wiring method is used, Metal Core Deluxe mkII delivers the full breadth of metal tones for hard rock to thrash.

3 distinct high gain amplifier models
3-band EQ
Switchable IR cabinet simulation
Settings auto-stored for each model
True bypass
USB-C for firmware updates & future software

Power supply: 9Vdc (PP3) battery or optional power adaptor
DC input connection: DC5521 jack (for optional adaptor - pin-negative)
Current consumption: <120mA
Controls: Gain, Master, Bass, Middle, Treble, Model switch
Modes: Duo Rect, Fireman, VH4
Input: 6.3mm jack
Output: 6.3mm jack
Input impedance: 1M ohm
Output impedance: 1k ohm
Dynamic range: 104dB
Dimensions: 122 x 72 x 47mm
Weight: 270g

In the box

The box for this item contains :

Metal Core Deluxe mkII pedal
Alkaline PP3 battery

Notes: MG-101 is a complete guitarist's tone companion in a compact yet versatile floor unit. Hiding inside the minimalist housing is a full suite of amplifier tones and a huge palette of guitar and bass effects across 10 distinct audio processing blocks. Amp modelling is based on TSAC-HD White Box Amp Modeling Technology, which delivers high definition analogue circuit simulation for pro quality guitar tones, with speaker cabinet emulation processed via an impulse response (IR) loader with 25 internal models and 12 additional user slots for importing your own files. A built-in expression pedal covers wah and swell effects amongst other possibilities. All settings can be edited onboard with parameters shown on the full colour display or via USB using the downloadable PC/Mac Quicktone software and then stored into one of 36 internal memory locations for recalling at will. In addition to the internal metronome, the built-in Jam function has a fully featured drum machine and 30 second stereo (60s mono) phrase looper. To integrate with a DAW studio suite, the USB also functions as a high quality audio interface, completing the studio-ready guitar rig. The main output can deliver stereo or mono audio directly to a PA or to guitar amplifiers, with a separate TRRS minijack output for headphones or 2-way connection to a smart phone for live streaming. Without breaking the bank, you can have world-class amp modelling and effects with all the essential tools a recording and gigging guitarist needs in a portable and convenient package.

Power supply: 9Vdc DC5521 pin-negative (power adaptor included)
Current consumption: <250mA
Inputs: 6.3mm jack (guitar), 3.5mm jack (aux input)
USB port: USB-C audio interface and PC/Mac editing
Sampling format: 48kHz, 32-bit
Frequency response: 20Hz - 20kHz (+/-1dB)
Output: 6.3mm stereo jack line out (to amp or mixer)
Headphone connector:3.5mm jack (TRRS for smartphone livestreaming)
Input impedance: Guitar 470k Ohms, Aux 25k Ohms
Dynamic range: 104dB
Output impedance: 1k Ohm
Dimensions: 289 x 160 x 71mm
Weight: 920g

In the Box:

MG-202 multi-effect pedal
9Vdc 500mA power adaptor
USB cable
User manual
Warranty card

Notes: MG-30 is the flagship modelling effect processor in the NuX range. Dual high speed processing offers accurate modelling of 30 different amplifier options, including bias tweaking for an extra dimension of response adjustment, all using the proprietary NuX TSAC-HD algorithm. Impulse response programming presents a choice of 8 guitar cabinets, 8 bass cabinets, 8 microphones in 3 different axis positions and even 3 acoustic guitar emulation profiles. Once the main guitar tone is programmed, there are 8 effects blocks which can be assigned to different positions in the signal chain, including WAH, CMP, GATE, EFX, EQ, MOD, DLY & RVB. An expression pedal covers wah and swell effects amongst other possibilities. Each has modes and/or parameters which can be adjusted and saved within the patch as needed. Real-time editing uses rotary encoders and switches, making for a natural and organic process and all prameters and graphics are displayed on a vibrant 4" colour display. Add to this a fully functioning USB audio interface, phrase looper, PC/Mac editor/librarian/updater, aux input, effects loop, drum machine and NMP-2 footswitch control and the MG-30 covers practically all bases. This unit provides all the processing power and audio quality that could be asked from any professional guitar processor at a fraction of the price of its component features.

Specifications:

Power supply: 9Vdc, 400mA pin-negative (adaptor included)
Inputs: 6.3mm jack (guitar), 3.5mm jack (aux input)
Outputs: 2 x 6.3mm jack (L/mono + R) to amp or mixer
Sends: returns: 6.3mm jack send (1k ohm) & return (220k ohm)
Headphone output: 3.5mm stereo jack
USB port: USB type-C for audio interface, PC/Mac editing & updating
Remote control connection: EXP1 TRS 6.3mm jack
Sampling format: 48kHz, 32-bit
Frequency response: 20Hz - 20kHz (i1dB)
Input impedance: 1M ohm
Output impedance: 1k ohm
Dynamic range: 110dB
Dimensions: 313 x 166 x 54mm
Weight: 1.5kg

The box for this item contains :

MG-30 multi-effects modeler pedal
1 x 9Vdc power adaptor (UK)
1 x NMP-2 dual footswitch (173.352UK)
1 x patch cable
1 x USB cable

Notes: The NU-X MG-400 builds on the success of the ground-breaking MG-300 compact multi-FX pedal, adding dual processors and delivering high-definition models and increased flexibility. Integrated effects sections include Drive, Amp Simulation, I.R cabinet simulation, Modulation, Delays & Reverbs with a host of options within each category. Audio modelling is based on the NU-X TSAC-HD algorithm, which delivers high-definition analogue circuit simulation for pro quality guitar tones. An expression pedal covers wah and swell effects amongst other possibilities. All settings can be edited onboard or via USB using the downloadable PC/Mac Quicktone software and then stored into one of 36 internal memory locations. For live or rehearsal backing, the built-in Jam function has a fully featured drum machine and phrase looper. To integrate with a DAW studio suite, the USB also functions as a high-quality audio interface, completing the studio-ready guitar rig. The main output can be stereo or mono for guitar amplifiers or D.I to studio equipment. There is an additional 3.5mm output for stereo headphones. Expanding the control surface has provided space for additional control footswitches for a smoother and more accessible live playing experience.

Specifications

Power supply: 9Vdc, 280mA pin-negative (adaptor included)
Inputs: 6.3mm jack (guitar), 3.5mm jack (aux input)
USB port: USB type-C for audio interface and PC/Mac editing
Sampling format: 48kHz, 32-bit
Frequency response: 20Hz - 20kHz (+/-1dB)
Outputs: L/Mono + R 6.3mm jack, stereo 3.5mm headphones
Latency: 1.1ms
Dynamic range: 108dB
THD: +N<0.03%
Input impedance: 470k ohms (Aux 10k ohms)
Output impedance: 1k ohm (Headphones 47 ohms)
Dimensions: 289 x 160 x 71mm
Weight: 920g

In the box

The box for this item contains:
MG-400 multi-FX pedal
9Vdc UK power adapter

Notes: Mighty Lite BT now reaches the mkII generation with this reinvented model, adding new features, modes and computer editing to an already winning formula, bringing a world of sonic possibilities to the guitar player in a compact and convenient package. Keeping with the desktop form factor and powered by 6 x AA batteries or optional 9V adaptor, the mkII adds a USB type-C port which can connect to a PC or Mac computer to edit settings using the Mighty Editor software. In addition, the Bluetooth connection enables wireless editing via the Mighty Amp app. Both software and app are free to download from www.nuxefx.com. Mighty Lite BT mkII also supports audio streaming over Bluetooth for backing tracks and a built-in drum machine for solo practice. New features include effects, modulations and new amp models with an IR loader for flexible cabinet simulation, which can be programmed and stored into 7 internal presets. This new version offers a huge palette of tones in a manageable and versatile package for bedroom practice, project studios and travelling guitar players.

Bluetooth audio streaming and preset editing
USB type-C port for PC/Mac editing and firmware
Mighty Editor™ software and Mighty App™ free to download
Inbuilt drum machine and metronome
Digitally modelled effects, modulations, delay and reverb
Selectable amp models, cabinet IR loader and acoustic IRs
5 Watt speaker
Runs from 9Vdc power adapter (not supplied) or USB via power bank or 6 AA Batteries
Suitable power supply: 173.290UK
Power supply: 9Vdc (6 x AA battery or optional adaptor) or USB-C (185mA)
Power in: 9Vdc, 120mA (5.5 x 2.1mm DC jack pin negative)
Inputs: Guitar in (6.3mm jack), Aux in (3.5mm jack)
PC Com: portUSB type-C
Speaker: 75mmO (3") 5W, 4 Ohm
Phones output: 3.5mm jack
Dimensions: 166 x 124 x 98mm
Weight: 720g

In the box
The box for this item contains :
Mighty Lite BT mkII amplifier

Notes: A mini chorus effect pedal with 3 switchable modes for Chorus, Flanger and Pitch Modulation. Chorus thickens the sound by modulating a short delay effect, producing a swirling ethereal tone. The Flanger effect tightens this by shortening to a very fine delay and regenerating it for rotating and tubular jet sounds. Pitch Modulation provides a lighter chorus effect by slightly varying the pitch and mixing back with the dry signal. All 3 are selected by an illuminated push button above the controls. Holding this button down during power-up selects between mono output or stereo output, which requires a stereo jack lead. Controls include Speed, Width and Intensity to adjust each effect as required, Pressing the footswitch engages or disengages the effect. The smart tap tempo feature means that the pedal recognises pressing the footswitch twice or in a short space of time and responds to the timing as a tap tempo function to adjust the speed setting. An extremely versatile modulation effect to give space and motion to chords and picked passages alike.

Power supply: 9Vdc (DC5521 connector, negative centre, adaptor not supplied)
Controls: Speed, Width, Intensity and Chorus/Flanger/Pitch Mod switch
Dimensions: 94 x 53 x 51mm
Weight: 175g

In the box

The box for this item contains :

Mini Super Chorus/Flanger/Pitch pedal

Notes: Multi Delay and Reverb effect pedal with inside routing and secondary reverb effects. One of the best Delay and Reverb algorithms in a metal box. Special select 3 classic Delays & 3 classic Reverbs . . . and we added a bonus "Shimmer" and "Freeze" effects which let you create a dreamy waterfall shimmer~ especially handy for intros, interludes, and endings. And now, because of NUX's latest Core Image Technology, the new Verdugo Series effect pedals offer pro-level sound enhancement.

Notes: Desktop-Friendly Multi-Functional MIDI Controller

Maximize your favourite DAW with the NTK-37's dedicated control integration. This controller offers intuitive handling of popular DAWs like Cubase, Logic Pro, and Pro Tools through Mackie, Hui, and CC protocols, providing essential mixer, transport, and control functions at your fingertips.

When you're on the go and need to complete work quickly, the NTK-37 is your ideal companion. Its streamlined controls give you instant access to the most critical elements of your projects and sounds, simplifying complex tasks so you can work efficiently, no matter where you are.

Integrated Transport Controls

The NTK-37 comes equipped with an integrated transport control module, featuring essential functions like loop, stop, start, record, rewind, fast forward, read, and write. These frequently used transport controls, paired with 9 faders, allow for quick management of your DAW's core features, making the arrangement process more convenient and efficient.

The NTK-37 also includes a mouse control pad, allowing you to customize each fader's function via the NTK Editor software. With the five-way selector and mouse pad, you can achieve precise control over your projects and sounds, giving you total command of your music production setup.

Feature-Rich Compact Keyboard

The NTK-37 offers quick USB-powered connectivity, making it easy to control any music production setup. Its velocity-sensitive keys with aftertouch allow you to choose from three different velocity curves, helping you find the perfect key-to-sound mapping for your style. The scale and arpeggiator functions can be used to control both hardware and live performance setups.

Specifications

- Keys: 37 full-size semi-weighted velocity-sensitive keys
- Sliders: 9 sliders
- Functions: Aftertouch, Arpeggiator (7 Types), Smart Scales (16 Scales), Key Touch Curves (5 Types), Key Touch can be Fixed 64 or Fixed 127
- DAW Controls: Play, Record, Stop, Rewind, Loop, Fast-Forward, Read and Write automation envelope
- Performance Controls: Pitch Bend Wheel, Modulation Wheel
- DAW Presets: 8+1 (User)
- User Scenes: 16 Scenes
- Weight: 4.0 kg (8.0 lbs)
- Dimensions: 29.3" x 8.3" x 2.8"

Notes: ***B-STOCK: Box damaged, product in perfect working order***


Desktop-Friendly Multi-Functional MIDI Controller

Maximize your favourite DAW with the NTK-37's dedicated control integration. This controller offers intuitive handling of popular DAWs like Cubase, Logic Pro, and Pro Tools through Mackie, Hui, and CC protocols, providing essential mixer, transport, and control functions at your fingertips.

When you're on the go and need to complete work quickly, the NTK-37 is your ideal companion. Its streamlined controls give you instant access to the most critical elements of your projects and sounds, simplifying complex tasks so you can work efficiently, no matter where you are.

Integrated Transport Controls

The NTK-37 comes equipped with an integrated transport control module, featuring essential functions like loop, stop, start, record, rewind, fast forward, read, and write. These frequently used transport controls, paired with 9 faders, allow for quick management of your DAW's core features, making the arrangement process more convenient and efficient.

The NTK-37 also includes a mouse control pad, allowing you to customize each fader's function via the NTK Editor software. With the five-way selector and mouse pad, you can achieve precise control over your projects and sounds, giving you total command of your music production setup.

Feature-Rich Compact Keyboard

The NTK-37 offers quick USB-powered connectivity, making it easy to control any music production setup. Its velocity-sensitive keys with aftertouch allow you to choose from three different velocity curves, helping you find the perfect key-to-sound mapping for your style. The scale and arpeggiator functions can be used to control both hardware and live performance setups.

Specifications

- Keys: 37 full-size semi-weighted velocity-sensitive keys
- Sliders: 9 sliders
- Functions: Aftertouch, Arpeggiator (7 Types), Smart Scales (16 Scales), Key Touch Curves (5 Types), Key Touch can be Fixed 64 or Fixed 127
- DAW Controls: Play, Record, Stop, Rewind, Loop, Fast-Forward, Read and Write automation envelope
- Performance Controls: Pitch Bend Wheel, Modulation Wheel
- DAW Presets: 8+1 (User)
- User Scenes: 16 Scenes
- Weight: 4.0 kg (8.0 lbs)
- Dimensions: 29.3" x 8.3" x 2.8"

Notes: Top Choice for Music Creators and Producers

The NUX TRACK KEYBOARD 49 is a versatile 49-key USB-powered MIDI controller designed to provide seamless integration with your DAW (Digital Audio Workstation) and virtual instruments. With its hassle-free connectivity, stylish design, and intuitive controls, this MIDI keyboard enhances your music production workflow, making it the perfect choice for both beginners and professionals.

Advanced Features for Creative Control

Equipped with a weighted keyboard and aftertouch, the NTK-49 adapts to various virtual instruments, allowing you to trigger different effects with precision. Its integrated faders and knobs provide real-time control over multiple MIDI CC parameters, enabling you to save custom presets and quickly edit template projects. Whether you're composing, recording, or performing, the NTK-49 offers all the tools you need to bring your music to life.

Innovative Design for Inspired Music Production

With a modern design that prioritizes ease of use, the NTK-49 not only facilitates project navigation and performance but also inspires creativity. The built-in arpeggiator and scale functions help you create intricate melodies, unique rhythms, and dynamic chord progressions. This MIDI controller is designed to spark new ideas and take your music production to the next level.

Comprehensive Software Integration and Customization

The NTK-49 is more than just a MIDI controller. It comes bundled with Cubase 13 LE, an industry-standard DAW, and the NUX NTK Editor software for complete control customization. These tools allow you to precisely map each control to suit your specific workflow, making it easier to produce high-quality music.

Supporting up to 8 different DAWs with quick control capabilities, the NTK-49 gives you the flexibility to define faders and knobs to transmit distinct MIDI signals, allowing simultaneous control over your DAW and virtual instruments. This feature streamlines your creative process, whether you're composing, mixing, or mastering.

Unique Built-In Mouse Control Pad for Seamless Workflow

One of the standout features of the NTK-49 is its unique mouse control pad, which integrates directly into the keyboard. This innovation allows you to easily navigate projects, select tracks, and adjust plugin effects without needing to switch between devices. The keyboard's five-way encoder further enhances your workflow by enabling zoom, track selection, and cursor alignment-all from the convenience of your MIDI controller.

Specifications

- Keys: 49 full-size semi-weighted velocity-sensitive keys

- Knobs: 8 knobs

- Sliders: 9 sliders

- Functions: Aftertouch, Arpeggiator (7 Types), Smart Scales (16 Scales), Key Touch Curves (9 Types), Key Touch can be Fixed 64 or Fixed 127

- DAW Controls: Play, Record, Stop, Rewind, Loop, Fast-Forward, Read and Write automation envelope

- Performance Controls: Pitch Bend Wheel, Modulation Wheel

- DAW Presets: 8+1 (User)

- User Scenes: 16 Scenes

- Weight: 5.0 kg (11.0 lbs)

- Dimensions: 35.8" x 8.3" x 2.9"

Notes: Professional Experience at Your Fingertips

Experience the ultimate in music creation with the NUX Track Keyboard 61, a state-of-the-art MIDI controller. Powered via USB-C, this all-in-one controller integrates a mixer, velocity-sensitive drum pads, and expertly mapped 61 keys, ensuring seamless creation whether you're at home or on the go. It's a true creativity hub!

Designed with input from artists worldwide, its layout is tailored for music production, making your workflow smoother and more focused.

Seamless DAW Integration

Bundled with Cubase LE, the NTK-61 effortlessly maps to most DAW software, offering quick and automatic matching. This ensures perfect harmony between the physical controller and your digital audio workstation, including faders, signal transmission, and channel or pan controls. Simply select your preferred DAW on the device, follow the setup guide, and enjoy instant compatibility with various VST instruments for real-time creation and mixing.

Intuitive Control Features

Enhance your production efficiency with the built-in mouse trackpad, ideal for both stage performances and studio compositions. Essential features like note repeat and an arpeggiator cater to popular music styles, including pop, hip-hop, and electronic. The onboard MIDI mode allows quick CC controller matching between hardware and virtual instruments, with customizable layouts that you can save and recall as needed.

Total Control, Infinite Possibilities

The lightweight NTK-61 is equipped with semi-weighted keys with touch curve options for a satisfying touch and creative inspiration. Its Aftertouch feature lets you link any desired sound effect (EXP, MOD, PITCH, etc.) to the aftertouch response, enhancing the authenticity and dynamic range of your sound creation.
Versatile Performance and Quick Presets

Switch instruments effortlessly between drum pads and keyboard with channel changes, enabling dual-hand control of two VST instruments. Utilize the NUX NTK Editor software for rapid device preset management, or download supported preset files for quick control of various DAWs and virtual instruments.

Specifications
- Keys: 61 full-size semi-weighted velocity-sensitive keys
- Pads: 8 velocity-sensitive pads (Bank A/B Button for expansion to 16 pads)
- Knobs: 8 knobs
- Sliders: 9 sliders
- Functions: Aftertouch, Arpeggiator (7 Types), Smart Scales (16 Scales), Key Touch Curves (9 Types), Key Touch can be Fixed 64 or Fixed 127
- DAW Controls: Play, Record, Stop, Rewind, Loop, Fast-Forward, Read and Write automation envelope
- Performance Controls: Pitch Bend Wheel, Modulation Wheel
- DAW Presets: 8+1 (User)
- User Scenes: 16 Scenes
- Weight: 5.5 kg (12.0 lbs)
- Dimensions: 42.3" x 8.3" x 2.9"

Notes: Pulse is a miniature IR (impulse response) loader pedal, that can apply a specific tonal profile to the input signal. Speaker cabinets typically change the tone of a guitar or bass guitar in a musical way, which is often collected using a microphone for sending to a mixing console for recording or sound reinforcement. Connecting the signal to a mixer before the speaker usually produces a sterile and harsh sound, which is where the Pulse pedal comes in. This pedal can mimic the speaker cabinet and microphone, meaning that the guitar signal can be taken straight from the preamp section and injected into a channel on the mixer. Another use for IR loaders is to mimic the response of an acoustic guitar, making an electric guitar sound more like an acoustic or an electro-acoustic guitar sound more natural. Pulse has modes for guitar cab, bass cab or acoustic guitar with 8 selectable types of each, adjusted by Level and Space controls. A 3.5mm headphone output means that this pedal can also be used for silent practice and an inbuilt audio to USB interface means that it can be used as the front end for a PC or Mac computer recording setup. Pulse is an invaluable guitarists and bass players multi-tool for practice, live and recording duties.

Power supply: 9Vdc (DC5521 connector, negative centre, adaptor not supplied)
Controls: Level, Space, 8-model selector and 3 IR modes switch
Dimensions: 94 x 53 x 51mm
Weight: 175g

In the box

The box for this item contains :

Pulse IR loader pedal

Notes: Sculpture is a mini compressor pedal with professional performance. Sustain and level controls adjust the compression and output, whilst blend gives the ability to add back in some of the unaffected signal to give a more natural attack. Hold down the on/off pedal to switch between soft clip and clean compression modes. Perfect for long sustain chords and clean lead tones.

Adjustable sustain and level
Blend control to feed in some natural attack
Selectable soft clip and clean modes
Requires 9V center negative DC Power Supply 75mA current draw (Not Supplied)
Compatible power supply 173.290UK

Power supply: 9Vdc (centre-negative power adaptor required)
Current consumption: 100mA
Input impedance: 1M Ohm
Output impedance: 20 Ohm
Controls: Sustain. Blend, Level, On/Off/Mode switch
Dimensions9: 4 x 53 x 51mm
Weight: 174g

In the box
The box for this item contains :
Sculpture mini pedal

Notes: Voodoo Vibe is a mini guitar effect pedal that is recreates the rotating speaker effects produced by the classic uni vibe pedals used by famous guitarists from the 60's to the present day. Controls for Speed, Intensity and Volume give a wide range of adjustment to home in on the perfect vibe effect. An illuminated mini push button above the rotary controls can switch between a classic psychedelic vibe effect or a more chorus-type effect. Holding this button down during power-up selects between mono output or stereo output, which requires a stereo jack lead. Pressing the footswitch engages or disengages the effect. The smart tap tempo feature means that the pedal recognises pressing the footswitch twice or in a short space of time and responds to the timing as a tap tempo function. Perfect for trippy arpeggios and ethereal chord work.

Power supply: 9Vdc (DC5521 connector, negative centre, adaptor not supplied)
Controls: Speed, Intensity, Volume and Vibe/Chorus switch
Dimensions: 94 x 53 x 51mm
Weight: 175g

In the box

The box for this item contains :

Voodoo Vibe pedal

Notes: ***B-STOCK: Box opened, product in perfect working order***


Voodoo Vibe is a mini guitar effect pedal that is recreates the rotating speaker effects produced by the classic uni vibe pedals used by famous guitarists from the 60's to the present day. Controls for Speed, Intensity and Volume give a wide range of adjustment to home in on the perfect vibe effect. An illuminated mini push button above the rotary controls can switch between a classic psychedelic vibe effect or a more chorus-type effect. Holding this button down during power-up selects between mono output or stereo output, which requires a stereo jack lead. Pressing the footswitch engages or disengages the effect. The smart tap tempo feature means that the pedal recognises pressing the footswitch twice or in a short space of time and responds to the timing as a tap tempo function. Perfect for trippy arpeggios and ethereal chord work.

Power supply: 9Vdc (DC5521 connector, negative centre, adaptor not supplied)
Controls: Speed, Intensity, Volume and Vibe/Chorus switch
Dimensions: 94 x 53 x 51mm
Weight: 175g

In the box

The box for this item contains :

Voodoo Vibe pedal