Studio Equipment charts

Notes: A typically unique take on multi-effects from Soma, designed to induce meditative states. Hybrid analogue-digital delay/reverb/granular processing gives a range of creative approaches.

Supplier's Notes:
COSMOS is a drifting memory station designed to work with meditative states through music. The design of the controls, functions and generated soundscapes are intended to evoke, in both performer and listener, states and experiences inherent in meditation, such as limitless space, fluidity, spontaneous development, presence, the ability to hear, tranquility, the experience of subtle harmony and happiness enveloping the whole world.

From a functional point of view, COSMOS is a large array of sound memory, in which recorded sounds undergo constant recombinations, spontaneously generating an ever-changing soundscape. This is achieved in three ways - by a mathematical shift based on the relationships between large prime numbers (the size of all delay lines are different primes), an asynchronous operation of the LFO, and modulation with a slowly changing chaotic signal. As a result, it allows the endless layering and processing of various sounds, as in a looper, but without an intrusive, repetitive loop.

COSMOS generates rich, fluid and evolving soundscapes perfect for ambient music. Using COSMOS, you can play an entire meditative solo concert while being in a spontaneous flow and without using studio-prepared sequences, backing tracks and other things that can't be a reflection of the "here and now".

Specifications

Minimum input voltage: 0.35 V peak-to-peak
Maximum output voltage at line outputs: 11.3 V peak-to-peak
The maximum output voltage at the headphones output: 10.4 V peak-to-peak
Frequency response: 10-22000 Hz
Sound memory: 44.7 sec
Supply voltage: 12 V *
Power connector polarity: centre plus
Current consumption: 0.25 A
Dimensions: 342 x 153 x 68 mm
Weight: 2.2 kg

* Use only the power supply supplied with the device! In case of failure, it can be replaced with a high-quality modern switched-mode power supply with an output voltage of DC 12 volts, the center is plus and an output current of at least 0.5 amperes (more is fine). The power supply must have a wide AC input voltage range of 100-240 volts. Such power supplies have excellent output voltage stabilization required for the device. It is forbidden to use COSMOS with nonstabilized voltage from transformer power supplies. It can lead to damage to the device, which is not covered by the warranty repair!

Notes: The 1010music line of stereo breakout cables are designed to connect 2 mono audio signals to a single stereo TRS 3.5 mm minijack plug. The slim plug caps fit side by side with other cables in compactly spaced input jacks, like those on the 1010music bluebox. These cables may have been designed for the bluebox, but they have a wide variety of uses with other gear as well.

Each of these cables has a male TRS stereo 3.5mm minijack plug on one end and two female TS mono 3.5 mm minijack plugs on the other end. They are 15 cm/6 in long with the 1010music logo printed on the plug caps.

This stereo breakout cable connects two 3.5mm female mono TS minijack plugs to the left and right channels of one 3.5 mm stereo TRS minijack plug. Red and black end caps on the female end differentiate the left and right channels. Each cable is 15 cm/6 in long and has slim metal caps with the 1010music logo.

Specifications:
15 cm / 6 in long
one 3.5 mm male stereo TRS to two 3.5 mm female mono TS
Nickel / 24K Gold plated connector
Highly flexible PVC / TPE Jacket Materials
Rohs, UL, CE, and FCC approved

Notes: Second-generation version of Korg's superb ModWave synth, building on the legacy of the iconic Wavestation with 60-voice polyphony, Kaoss Physics and Motion Sequencing 2.0.

Supplier's Notes:
Modwave is a synthesis powerhouse with distinctive wavetable timbres, Kaoss Physics, and Motion Sequencing 2.0. The new Modwave mkII provides an astonishing 60 voices of polyphony almost double that of the original Modwave. All LFOs have been updated with options for free running, delayed start, and retriggering, and a pre/post switch for reverb sends has been added, alongside new modulation sources, and more.

Modern monster synth

In 1985, Korg introduced the DW-8000 - a synth which combined digital wavetables with rich analogue filters to give users sounds which were impossible to create with analogue oscillators.

Modwave builds on the DW legacy, transforming it into a modern monster synth, featuring incredibly deep wavetable oscillators, gorgeous filters, wildly flexible modulation, unmatched polyphony, comprehensive pattern sequencing, and immediately satisfying hands-on control to deliver unique, powerful, and easily customizable sounds and phrases.

Over 200 factory wavetables each contain up to 64 waveforms. 30+ Modifiers can be used to change their basic character, and 13 Morph Types to process them in real-time. Using the unique, realtime A/B Blend, it's possible to create new hybrids from any two wavetables.

Expanded possibilities

Modwave can be expanded by importing new wavetables using the free Editor/Librarian software. There are many free and commercial wavetable libraries in the standard Serum format, or you can create your own using the free, cross-platform WaveEdit software (available in a custom version for the Modwave). Wavetables can be layered with samples from the built-in, multi-gigabyte PCM library, or import your own 4 GB of samples using the Sample Builder software.

Each Program has two full-featured wavetable oscillators, plus a sub oscillator/noise generator and any of a dozen stereo filter types, including the aggressive MS-20, sweet Polysix, and the newly enhanced Multi Filter. Animate almost any parameter using the massively flexible modulation system, with four triggerable envelopes, five LFOs, dual mod processors and two key-track generators-plus multi-lane Motion Sequencing and Kaoss Physics.

Even with all that synthesis power, playing up to four simultaneous wavetables per voice in a single Program, the Modwave mkII achieves 60-voice polyphony, incredible for a wavetable synth. Layer two Programs together for double the possibilities.

KAOSS in motion

Modwave introduced two unique new tools for creating dynamic motion: Kaoss Physics and Motion Sequencing 2.0. KaossPhysics combines an x/y Kaoss pad with modulatable game physics to create a responsive, interactive controller that is extraordinarily powerful.

Motion Sequencing 2.0 brings the organic, continuously evolving patterns of the Wavestate Wave Sequencing 2.0 into the world of motion sequencing, including multiple lanes and real-time recording to help you create complex and evolving phrases that other step sequencers cannot.

Modwave's evolved wavetable synthesis delivers its own brand of completely unique sounds and a knob-per-function layout that makes customizing those sounds fast and easy. There are hundreds of preset sounds empowered by this new architecture, organised by front-panel category buttons, and all instantly customizable via the four Mod Knobs. Modwave'sdistinctive wavetable timbres start with aggressive basses & leads, and lush ambient pads which will add a new dimension to your tracks. But that is just the beginning.

Those who want to dig deeper will find an endless source of discovery; with the Modwave's unique synth architecture, you'll be finding new things for a long, long time. Save as many of your sounds as you like; there's room for thousands more. You can also load your own samples, import wavetables in standard formats, and create your own wavetables using the free WaveEditsoftware.

KAOSS Physics

Kaoss Physics models a ball rolling on a surface and bouncing off walls. The surface can tilt in any direction, and a bump with variable height/depth and location attracts or repels the ball. Adjustable friction slows the ball's travel, and adjustable time controls the speed of the entire model. All of these characteristics are modulatable, so you can change them in real-time!

Start the ball by flicking a finger on the x/y pad, or launch the ball automatically using another modulation source. You can even directly control the ball by holding your finger on the pad. The position of the ball produces eight modulation signals, which can be used to control any modulation destination: the X and Y locations, the distance from the centre, the angle relative to the X axis, and separate signals for +/- X and +/- Y.

Walls can slow down the ball, as if they were padded, or accelerate the ball, like bumpers in a pinball machine. The walls can also be removed entirely, so that the surface wraps around to the opposite edges like a vintage arcade game.
The modelled environment can create specific modulation effects. For instance, use a centered bump with negative height so that the modulation values always eventually return to 0. Or, position a bump with positive height on a side or a corner, to push modulation values away from that zone.

The result is an interactive controller that amplifies your physical gestures, transforming them into complex musical results.

Motion Sequencing 2.0

Motion Sequencing 2.0 is evolved from the Wavestate's Wave Sequencing 2.0. Timing, Pitch, Shape, and four sets of Step Sequence values are separated into "Lanes," each with their own loop start and loop end, adding a deeper, more customizable level of phrase and modulation recording.

Every time the sequence moves forward, the individual Lanes are combined to create the output. For instance, a step sequence value may be matched with a different duration, pitch, and shape every time that it plays. You can modulate each Lane's loop points separately for every note, using velocity, LFOs, envelopes, Mod Knobs, or other controllers. Each note in a chord can be playing something different!

Lanes can also randomize the step order every time they play. Finally, individual steps can be randomly skipped, with a modulatable probability from 0 to 100%. The result is organic, ever-changing sounds that respond to your control. The dual onboard arpeggiators can interact with Motion Sequences for even more possibilities.

Wavetables

Wavetables are sets of single-cycle digital waveforms, arranged in a specific order. The wavetable's "position" determines which waveform is played. Moving the position with an envelope, LFO, or other modulation source creates subtle or dramatic changes in timbre. Some wavetable systems switch abruptly from one waveform to another; others crossfade smoothly between them. Modwave can do either one.

Modifers

Use over 30 Modifiers to alter the character of any wavetable at load time. For instance, isolate the odd or even harmonics, add weight through anti-aliased quantization or saturation, or revisit the gritty character of old-school wavetable synths with the Vintage 8 & 12 options.

Morph

The 13 Morph Types let you stretch, squeeze, reflect, and otherwise alter the wavetables in real-time, changing their timbre andiwhen modulatedicreating additional motion in the sound. Sync creates classic swept-sync timbres, using only a single oscillator. Three special Morph TypesiFM, AM, and Ring Modimodulate Osc 2 with Osc 1, and the last two even apply to samples.

A/B Blend

Using the unique A/B mode, oscillators can blend any two wavetables with phase-synchronous precisionidifferent from simply layering voicesiopening up a dimension of intermediate waveforms. Add body to otherwise "thin" waveforms, for instance, or a touch of sizzle to a mellow timbre. Even fade between two different "modifier" versions of the same wavetable. A/B Blend can be modulated in real-time, of course.

Or, step outside the box with Korg's unique Multi Filter, which creates modulatable blends of multiple modes simultaneously - now with presets on a front panel knob, for easier exploration of its many possibilities.

An arsenal of effects

Modwave's superb effects deliver production-ready sounds. Each Layer has three dedicated effects, plus a send to the Performance's master reverb, followed by a master parametric EQ. Along with standards such as compressors, EQs, choruses, flangers, phasers, and stereo delays, you'll find distinctive processors such as the Wave Shaper, Talking Modulator, Reverse Delay, Multiband Mod Delay, and Overb (from the OASYS and Kronos), plus modeled effects including VOX guitar amps, VOX wah, multi-head tape echo, and a collection of classic guitar pedals.

Notes: Connect your USB compatible gear with Audio Optimized UDG Ultimate Cables.

This USB 3.2 cable with a streamlined design helps DJ's and Producers maximize their performance and is ideal for home and professional use where impeccable audio is a must.

UDG Ultimate Cables are designed to interconnect devices with USB interfaces. It is ideal for connecting an audio interface, USB microphone, instrument or most computer peripherals to a PC.

The UDG Ultimate Cables deliver professional performance made with superior flexible PVC cable construction, UDG branding on cable ends and Velcro cable strap validates they're official.

For devices with an older USB version, this cable is backward compatible so you can still make the connection.

Specifications

Colour Orange
Length: 1.5 m | 4.92 ft
Weight: 0,10 kg / 0.22 lbs
Material: PVC + Metal

Protection:

Constructed with corrosion-resistant, gold-plated connectors for optimal signal
Two ferrite chokes: help eliminate noise in both directions
Includes UDG Velcro strap for easy storage
High-quality multi-shielded PVC USB cable

Extras

High-speed Audio Optimized USB 3.2 C-Male to C-Male cable
Maximum data transfer rates up to 20 Gbps
4k @ 60Hz video support
Ergonomic UDG Design
Various colours makes them easy to identify

Fits

Connects mic, keyboards, and speed-critical devices, such as audio interfaces and external hard drives to your computer

Notes: Connect your USB compatible gear with Audio Optimized UDG Ultimate Cables.

This USB 3.2 cable with a streamlined design helps DJ's and Producers maximize their performance and is ideal for home and professional use where impeccable audio is a must.

UDG Ultimate Cables are designed to interconnect devices with USB interfaces. It is ideal for connecting an audio interface, USB microphone, instrument or most computer peripherals to a PC.

The UDG Ultimate Cables deliver professional performance made with superior flexible PVC cable construction, UDG branding on cable ends and Velcro cable strap validates they're official.

For devices with an older USB version, this cable is backward compatible so you can still make the connection.

Specifications

Colour Red
Length: 1.5 m | 4.92 ft
Weight: 0,10 kg / 0.22 lbs
Material: PVC + Metal

Protection:
Constructed with corrosion-resistant, gold-plated connectors for optimal signal
Two ferrite chokes: help eliminate noise in both directions
Includes UDG Velcro strap for easy storage
High-quality multi-shielded PVC USB cable

Extras:

High-speed Audio Optimized USB 3.2 C-Male to C-Male cable
Maximum data transfer rates up to 20 Gbps
4k @ 60Hz video support
Ergonomic UDG Design
Various colours makes them easy to identify

Fits:

Connects mic, keyboards, and speed-critical devices, such as audio interfaces and external hard drives to your computer

Notes: A true legend of modular synthesis, Make Noise's Maths is arguably the definitive Eurorack function generator. Based on analogue computing circuits, Maths draws on Buchla-style techniques to offer countless ways of generating and processing modulation signals.

Supplier's Notes:
The MATHS music synthesizer module is an analogue computer designed for musical purposes. Amongst other things, it will allow you to:

Features

Generate a variety of linear, logarithmic, or exponential triggered or continuous functions

Integrate an incoming signal

With no signal applied, generate a variety of linear, logarithmic, or exponential functions

Add, subtract and OR up to 4 signals

Generate analogue signals from digital information (Gate / Clock)

Generate digital information (Gate / Clock) from analog signals

Delay digital (Gate / Clock) information

If the above list reads like science rather than music, here is the translation:

Voltage Controlled Envelope or LFO as slow as 25 minutes and as fast as 1khz

Apply Lag, Slew or Portamento to control voltages

Change the depth of modulation and modulate backwards!

Combine up to 4 control signals to create more complex modulations

Musical Events such as Ramping up or Down in Tempo, on command

Initiating Musical events upon sensing motion in the system

Musical note division and / or Flam

Perfect for modulating the DPO and just about anything else

Specifications
Width: 20hp
Max Depth
(incl. power cable): 32mm

Power:
60mA@ +12V
50mA @ -12V

Notes: The 'Mega Milton' is a smorgasbord of handy all analogue utilities in just 8HP that will greatly extend the functionality of your Eurorack system.

It includes a stereo line input converter for incorporating line level external sources into a Eurorack system, a fixed 4 input mixer with breakout attenuator for combining signals, a gated slew limiter for adding slides to sequences, a sample and hold with analogue white noise with a myriad of uses such as generative melodies or producing percussive textures and finally a buffered mult for droop free signal distribution with handy LEDs to monitor.

All sections are normalised to help with typical use cases such as generating random CV from the sample & hold section, a smooth random source from the slew output and breaking out a standalone attenuator from the fourth mixer input.

The 'Mega Milton' provides essential classic synthesizer building blocks for patching in any Eurorack system.

Ideal For

Incorporating stereo external sources easily into your Eurorack system.
Signal attenuation and basic mixing in a small space.
Building percussion sounds from an analogue noise source.
Producing clocked random to add interest and variation to patterns and sounds.
Adding gated 303 style slides to patterns.
Creating and Manipulating patterns with Sample and Hold.
Buffering and monitoring voltage across multiple VCOs or other destinations with no drop.

Tech Specs

Supply: +12V 70mA / -12V 70mA
Size: 8HP
Depth: 32mm

Notes: Coiled black 1.5m thermo plastic cable with soft touch surface. Extends up to 3.2m. Perfect for DJing or small studio use. Comes with 1/4 to 1/8 screw-on adapter.

Notes: A massive semi-modular system in a small case with the footprint of a laptop. Cascadia has MIDI in/out/thru/USB, Eurorack compatible signal levels and pro-level audio I/O to interface with the rest of your studio or get your studio started.

Modern Analog Architecture
Cascadia is packed with a mix of classic East and West Coast synthesizer blocks. Normalized connections let you get straight to the sounds inside. Or, let your imagination run wild and patch any of the modules together however you choose. Make small tweaks to the architecture, or re-route the entire synth to your likingithe choice is yours!

Two Precision Analog VCOs
VCO A is Thru-zero FM-ready with a dedicated Index VCA, Sub Oscillator, PWM and Soft/hard sync.
VCO B is a combo VCO/LFO with 4 simultaneous outputs
Six Channel Waveform Mixer
Two patchable (normalled) inputs
Noise generator with multiple algorithms.
Optional asymmetric soft clipping on the mix output.
Liquid-Sounding, Cascaded 4-Pole Multimode Filter
Eight Modes: LP1, LP2, LP4, BP2, BP4, HP4, NT2, Phazor.
Additional dedicated outputs for LP4 and HP4.
Input Level Knob for fine control of filter input and resonance balance and added drive.
Multiple FM inputs and a QM input, all with attenuators.
Wavefolder Circuit
West Coast-style parallel wavefolder.
Normalled into the auxiliary input on the VCA in parallel with the filter.
Dual Digital Envelopes
ENV A is a versatile east coast style ADSR / AHDSR envelope generator with a hold function and dynamic level/time control. Normalled to the VCA to instantly shape your sound.
ENV B is a complex, multimode function generator with a West Coast style AR/ASR/Cycling AR, a beat syncable LFO, Burst generator modes, and the Entropic Sequence Generator (added in 1.3). Normalled to the filter for instant FM without patching.
VCA A and Output Path
VCA A is a linear VCA with auxiliary input.
Global Output Mixer with overdrive circuit and bypassable asymmetric soft clipping.

Expansive Utilities Sections
Cascadia also features a whole host of utilities for getting the most out of your patches.

The Utility Row
Sample and hold circuit with white noise normalled to the input.
Slew/Envelope follower.
Attenuverter/Mixer with multiple outputs.
Triple triangle LFO with rate control, rate input and divided outputs.
Triple buffered multiple.
Precision adder.
Signal inverter.
Bi-polar > Unity level shifter.
Expression level control for modulation the TRS expression input on an FX pedal.
Ring Modulator.
VCA B / LPF (LPG) i Auxiliary VCA and 4-Pole Diode Ladder VCF combination for additional dynamics.
The Top Row
Easy to access Pitch, Gate, and Velocity CV inputs.
Pedal Send and Return FX loop with Wet/Dry control, phase inverter and Line/Pedal level switches.
Output Mixer with Overdrive.
Eurorack Level Main output with level control for interfacing with other modular gear.

The Outside world i MIDI, Pedal and Audio I/O
Cascadia is equipped with a ton of I/O to get it connected to the rest of your gear.

Rear Panel
14" Stereo Headphone jack.
14" Balanced Output Jack.
14" Balanced Input routed to a slider and output on the main panel for patching anywhere into Cascadia.
14" TS Pedal FX Send Return and 14" TRS Expression Out.
MIDI DIN In/Out/Thru and USB-MIDI all routed to the MIDI > CV Interface on the top panel.
MIDI > CV Interface
Deeper MIDI configuration is available with our Intelljel Config App (link below). MPE Support has been added in v1.4 and supports the Ableton Live 12 Tuning systems. Dual Mono mode (added in 1.3) allows an additional channel to send it's own Pitch/Gate signal on the CC/MOD outputs. All modes support MIDI Portamento.

MIDI Pitch / Velocity Outputs and Learn Button
MIDI Gate / Trig Outputs
MIDI CC / Mod i Learnable and assignable to any CC or Channel Pressure
MIDI LFO i Multimode LFO synced with MIDI or Tap Clock
MIDI CLK i Dividable MIDI clock with alternate Tap Clock functionality.
Cascadia comes ready to play.
The normalization behind the panel allows for a ton of exploration without ever adding a patch cable; there is years of material to explore in Cascadia and years more when you start patching. We've included everything you need to get started: 14 assorted patch cables, USB-A to USB-C cable, and an international power supply.

Expand and Customize
In addition to additional patch cables, we have additional options for swapping the wooden cheeks for metal side cheeks or a rackmount kit with a storage trayigreat for an effects pedal or patch cables.

Specs
In the Box Cascadia Semi-modular Synthesizer
14 Patch cables i 4×10cm, 4×15cm, 4×30cm, 2×45cm
USB-C to A cable
Intellijel cable tie
15V/1.2A AC Adaptor (Euro/American prongs included)
Height 66mm (from rubber foot to top of knobs)
Width 348mm (including wood end cheeks)
Depth 246mm (front to rear jacks).
Power 15V DC/1.0 A (minimum), center-pin-positive.

Notes: A true MIDI powerhouse, based around a 128-pad matrix and 16-track MIDI sequencer with slick programming workflow and Ableton-style pattern mode for live performance.

*** Version 2.0 updates - January 2024 ***

In this version, Squarp have put a lot of effort into improving the ergonomics and screen designs.

As for features, the focus has been on expanding patterns from 8 to 16 per track. Follow-actions have been introduced to bring more life to your sections, adding logic and randomness to the construction of your tracks.

A new MixMute mode has been created to enhance live performances, improve transitions between projects and arm your tracks for multitrack recording.

Now you can engage in multi-track recording and capture on multiple tracks simultaneously.

Two new effects are making their debut as well: FX ECHO, the best delay Squarp have made so far, and FX OUTPUT, allowing rerouting to a different output in the middle of the effect chain.

You can now Import/ExportMIDI files, either to save and reuse your own patterns in different projects or to load complex MIDI files from a computer.

The Curve algorithm is now accessible in automation mode, Squarp have added a track compensation mechanism and Auto-load.

Supplier's Notes:
Professional standalone sequencer

Genuine centerpiece of a setup, it offers every tool needed to compose songs in the studio and perform them on stage. From vintage to modern synths, from modular systems to your favourite DAW, Hapax can sequence and synchronize all your gear, while bringing you carefully crafted tools, designed for maximizing creativity.

The midi powerhouse.

Up to a million notes and events

16 tracks per project, 8 patterns per track.

Thanks to its dual-processor architecture, Hapax can record and transform tremendous amounts of data in no time, without a hitch.

Express yourself.

MPE compatibility

Hapax is the first hardware sequencer that fully supports MIDI Polyphonic Expression. Record the finest gestures, slides and articulations of your playing, without compromising quality.

Around the clock performance.
Dual-project architecture



Hapax can handle two separate and independent projects, that can be played simultaneously. This lets you compose or load an entire project while the first one is already playing, enabling endless sets and seamless transitions.

Dawless is more.

Hapax offers broad connectivity options for perfect integration in any setup.

Adaptive workflow.
Several ways to write music
Writing a melody: use a polyphonic or MPE track and take advantage of the advanced step sequencer to quickly lay down notes or edit your live recording.

Composing a beat: control up to 8 different instruments with a single track. The drum sequencer is tailored for very easy rhythm writing and jamming.

Real-time midi effects.

Bring your synths to life

Hapax embeds multiple real-time, polyphonic, non-destructive midi effects, as well as project-wide assignable LFOs. Each parameter of these effects can be automated in the dedicated mode, and processed in the mod matrix, which provides even more ways of routing and modulating.

Powerful composition tools.

Algorithms

Powerful tools for offline note transformation and generation, right at your fingertips. Harmonically invert your motive, generate a controlled-random counter-melody, slowly ramp up the velocities, emphasize every fifth 8th note...

Hi-res recording

Hit the red button, and record from the encoders and 128 pads of Hapax, external midi instruments (included MPE controllers) or any incoming analogue signal, at a high resolution of 192 ppqn. Looper style recording, count-down and metronome options, punch-in mode, you'll certainly find the options that best suit your workflow.

Time elasticity

Each track has an elasticity value which changes its playback speed, expressed in percentage of BPM. Quickly double or halve the speed of a track, or create slightly shifted tracks that will slowly drift out of phase with each other.

Fluid editing

Using hardware should never get in the way of creative flow. The undo/redo button lets you go back in time as needed, thanks to its extensive history. Additionally, the snapshot function enables you to save the state of a pattern and recall it with a single press. Together with dedicated copy, paste and delete buttons, Hapax offers a complete toolbox for the prompt editing of your tracks.

Harmony, simplified

For fast and intuitive chord building, the chord live mode brings harmonic capabilities to anyone, with or without deep theoretical knowledge. With its colourful interface, the chord mode displays a synesthetic melding of hearing, vision and touch.

Simple by design.

Trimmed to perfection

Squarp designed Hapax from the ground up, deconstructing everything you thought you knew about sequencing- aiming for a high-end product, with dual arm processors for computation power and a rugged yet minimalist housing.

As music-making should remain an enjoyable process, dedicated buttons were over key combinations and imagined a clear-cut interface as well as a simple architecture. Squarp have striven to minimize the importance of screens for live performing, but the dual grayscale display helps keeping track of things in a studio context.

Hapaxos
Evolving firmware.
The Hapax Operating System has been written with extra care, prioritizing stable and fast operations. New features and parameters will be added regularly.

Specifications
Model name: Hapax
Hardware: 128 RGB MATRIX pads
52 clic pads
9 sturdy clickable encoders
2 OLED greyscale displays
SD card for saving projects
CPU: dual ARM design
RAM: 32MiB
Housing: machined aluminium 2mm
Housing (back): unibody ABS

Sequencer
Dual Sequencer (2 Projects)
16 tracks per project
8 patterns per track

Input
2× midi in (DIN + TRS)
2× CV in [-5V to +5V] (16bit)
Stereo pedal (footswitch)

Output
4× midi out (3× DIN + TRS)
4× CV out [-5V to +5V] (16bit)
4× GATE out [+5V]

Bidirectional I/O
USB Host (link a controller)
USB Device (link a computer)
Power supply: 15V, 1.2A, 18W (included)
Dimensions: 358 × 206 × 48 mm
Weight: 1.855 kg

Notes: In 2009 Tony designed the first Skiff to complement the vertically oriented cases available at the time by providing an ergonomic enclosure for our Rene and Pressure Points touch controllers.

Today the Make Noise Skiff provides a smart way to build a small modular synthesizer. It is low cost, but extremely durable. The clean simple lines and matte black color place visual emphasis where the action is: the patch the artist has created. At one side there is a power button and the Make Noise logo is illuminated to show the power is ON.

Ships ready to use. Just add modules, patch cables, and inspiration.

Notes: C4RBN is a 4/2-pole state variable filter with input saturation, output wavefolding and more. It offers a wide range of characters, from nice and clean filter sounds to screaming, squeaky, sounds.

An innovative input saturation circuit and the output wavefolder of WMD's classic SYNCHRODYNE filter bring great sonic flexibility.

Features:

3 independent 2 pole outputs for High Pass, Low Pass, and Bandpass
Inverting Attenuator (attenuverter) for FM allows for positive and negative CV control over the cutoff frequency
Independent 4 Pole output with switchable frequency response
Input Saturation with 3 switchable levels and CV input for additional fine control
PING circuit generates a fast decay envelope emulating the response of a vactrol
Output wavefolder for extra bite and screaming character
Resonance with self oscillation
Temperature compensated 1V/Oct tracking.
Performance focused control scheme allows for on-the-fly changes of filter types with intention

Power consumption: 92mA at +12V and 82mA at -12V

Depth: 38mm

HP : 4

Notes: IsoAcoustics introduce the next evolution of their specialized line of speaker stands for the audio professional, music hobbyist, audiophile, and music lover. The new ISO Series of speaker stands provide superior acoustic isolation and enhance the sound clarity of any speakers including studio monitors, home theatre systems and sound reinforcement.

With a lower profile and new contemporary design, the ISO Series of stands positions your studio closer to the supporting surface or meter bridge, and the new redesigned isolators moves the acoustic performance another step forward.

IsoAcoustics ISO Series speaker stands are built with a unique, patented isolation technology that provides a high degree of isolations and manages the speaker's energy to deliver authentic, uncoloured sound. This next generation of speaker stands effectively eliminates energy transfer into the supporting surfaces. Bass becomes tighter, overall imaging is enhanced and your speakers are enabled to perform to their full potential. Following the same design philosophy as the ISO-L8R Series, these isolation stands provide 14 variations of height and tilt adjustment to optimize the placement and performance of studio monitors by getting the tweeters in the correct alignment with the listening position.

Whether you're a pro mixing in the studio - a musician creating in a home project environment - or an audiophile who appreciates every nuance of music and sound - you'll hear and appreciate the difference with the ISO Series speaker stands. It's simply the best investment you can make for superior audio.

ISO-200:

Designed for larger speakers and studio monitors. These stands provide 14 variations of height and tilt to optimize speaker placement and performance. Isolate your studio monitors from the supporting surface and allow them to breathe so they can deliver the clearest and most accurate sound possible.

7.8"x10"/20×25.4cm Short: 3.5"/12.5cm Tall: 8.75"/22.5cm 60 lbs/27.2kg

Notes: Set of 5 high-quality braided & soft 3.5mm patch cables for use with eurorack modules. The braided patch cables have a soft touch & are perfect for traveling with your eurorack system patched as they are super-bendable and much less likely to get tangled even with your case lid closed. Pleasant & practical for a better patching experience.

Notes: Your powerful and lightweight KeyStep 37 will instantly become portable with a proper case to protect it during travel. From composing in your DAW to jamming with hardware, the KeyStep 37 can go with you anywhere with this PULSE Case.

Description:

The PULSE Case for the Arturia KeyStep 37 was designed by musicians to be highly versatile for all your mobile mobile scenarios, from tossing it in the trunk to packing it inside your luggage. The KeyStep 37 case is made from rigid EVA material that holds its shape, and is shockproof and water-resistant.

This PULSE Case features an interior mesh pocket that can store any extra cables, as well as an ultrasoft velvet interior lining to prevent any scratches on the surface of the KeyStep 37. With the PULSE Case, you'll never have to worry about traveling with your controller, so you can focus on making great music!

Specifications:

Perfect fit for your Arturia KeyStep 37

Comfortable molded handle

Interior pocket for holding cables

Versatile and lightweight

Interior dimensions: 22.25 x 7 x 3 inches

Exterior dimensions: 23 x 8 x 3.5 inches

Notes: Second-generation version of 1010's outstanding Bitbox sampler module, featuring improved processing power, higher-quality touchscreen and new effects.

Supplier's Notes:
Next Generation Sampling Module for Eurorack

The bitbox mk2 is a follow up to 1010's successful bitbox module. Do more with bitbox mk2's more powerful processor and improved touch screen. This module has all of the features of the original bitbox and adds effects and mixing capabilities that take advantage of the faster and more powerful processor.

Sample Playback

Play up to 24 polyphonic notes when your samples fit in the 64 MB of internal memory or up to 8 larger samples streaming directly from the microSD card
Configure 16 sample pads per preset as single or multi-samples, clips, slicers, granular or new recordings
Stream long samples from the microSD card with a max sample size of 4 GB, which can be many hours of audio
Trigger samples with the touch screen, CV gate inputs, or MIDI input
Use MIDI for polyphonic playback of samples or slices
Control how samples start and stop by choosing from one-shot, toggle, and gate launch modes
Tweak playback through a variety of sample parameters, including start position, length, pitch, gain, filter, loop mode, launch quantization, ADSR, Exclusive Grouping, clip synchronization, slice placement and sequencing, grain size, grain spread, grain count, and MIDI note and channel mapping

Sample Recording

Record Eurorack level audio straight into the module:

Record samples from a stereo audio input pair
Configure each pad for stereo or mono recording with the option to synchronize the start and stop times to clock inputs
Trigger recording via audio level threshold
Create perfectly sized loops by setting the recording length
Enable immediate playback after recording for live looping capabilities
Make recordings up to 4 hours in length
Store recorded samples as WAV files on the micro SD card then remove the card to transfer them to your computer
Sample Modes

Find creative ways of using your samples with our 5 sample playback modes:

Trigger one shots or launch loops using sample mode
Load a folder of samples into a sample mode pad to improve the quality of the pitch shifting when playing a sample chromatically or to trigger different samples with each note
Play time-synchronized loops with constant pitch time shifting in clip mode
Skip between slices of a WAV using slicer mode
Create rich textures and other worldly sounds with granular mode
External Control and Synchronization
Playback can be immediate or synchronized to internal clock, TRS clock in, or MIDI clock in and out
Trigger each pad independently through a dedicated gate input
Use MIDI to trigger pads via a note per pad
Play a single or multi-sample pad pitch shifted using MIDI notes or CV
Trigger different sample slices using MIDI notes or CV
Modulate a wide variety of sample parameters through the MIDI input and up to 8 CV signals
Quickly set up MIDI modulation using Learn mode - no need to look up CC numbers
Module Features
Use the 3.5" diagonal touch screen to intuitively explore the features of the module
Get more creative with double the processing power of the original bitbox
Fill out your sound with reverb and delay
Import or export WAV files with your Mac or PC using a microSD card
Save and recall multiple presets
Increase your capacity with larger microSD cards
Select Flipped UI mode to mount the unit with the screen on the bottom and use the screen, knobs, buttons, and CV jacks as you normally would

When you purchase a bitbox mk2, you will receive:

a bitbox mk2 Eurorack module
a microSD card with with a bank of demo presets and samples loaded on it
a Eurorack power cable
a bitbox mk2 Quick Start guide
a MIDI Adapter

Technical Specs

Supports 1 and 2 channel WAV files with 16, 24 or 32-bit resolution at any sample rate (48kHz preferred)
26 HP
Module dimensions including knobs: 5.25" x 5"x 1.75"
Depth behind front panel with ribbon cable: 1.25"
+12V: 400mA
-12V: 0mA
5V: 0mA
24-bit ADC and DAC

Inputs and Outputs

Connect up to 8 CV modulators to control numerous sample parameters
Trigger each of the 16 pads with a dedicated gate input
Record through the dedicated stereo audio input pair
Use CV to keep time through the dedicated clock input
Confidently connect with both TRS MIDI Type A and Type B, no adapter needed
Route the audio from each pad out to one of 2 stereo audio output pairs or any of the corresponding single channels
Inputs and outputs are DC coupled so you can record and play out CV signals

Notes: Seriously potent polyphonic voice built around 16 sine-based oscillators. Capable of a huge range of tones thanks to FM, phase distortion and wavefolding. Another cracker from a consistently reliable brand.

Supplier's notes:
The Ensemble Oscillator is a unified polyphonic voice of sixteen complex oscillators combining additive, FM, phase-distortion and wavefolding synthesis techniques in new unorthodox ways. By quantizing the oscillators to scales or series of harmonics, the Ensemble Oscillator allows you to explore the sonic boundary between musical chords and rich evolving textures. Easily create a wide variety of sounds ranging from aggregates of pure sine waves to pulsar synthesis or pristine harmonic tones and lush wide chords to rich dirty drones and rumbling glitches. Custom scales can quickly be "learned" and saved using a CV keyboard or by manually entering notes with the controls.

The Ensemble Oscillator is designed by Matthias Puech and 4ms Company.

30 factory-programmed, user-writeable scales organized in three groups:
12TET: all notes quantized to equal temperament, repeating over octaves
Octave: unquantized notes, repeating over octaves
Free: unquantized notes, repeating over the interval between the lowest and highest note

16HP Eurorack format module
0.98" (25mm) maximum depth (including power cable)
10-pin to 16-pin Eurorack power header
Power consumption
+12V: 114mA maximum
-12V: 45mA maximum
+5V: 0mA (not used)
Audio outputs
Frequency range: 0Hz (DC) - 20kHz
Typical amplitude: 10Vpp
Maximum amplitude: 18.5Vpp
1V/oct inputs (Root and Pitch)
Voltage range: -2V to +6V (8 octave range)
Factory calibrated to 1.00V/oct
Per-jack user-calibration allows from 0.7V/oct to 1.3V/oct
CV inputs (other than 1V/oct)
Voltage range: -5V to +5V
Gate inputs
Trigger threshold: 2.5V
User memory (non-volatile)
Scale slots: 30
Shift feature settings
1V/oct calibration settings

Notes: A-138s is a simple but useful 4-in-2 mixing tool. It has four inputs available. Each input is equipped with an attenuator (Level) and a panning control that is used to distribute the signal to the left and right output. Beyond stereo mixing it is equally suited to create variable parallel routings. For example: Any of the four inputs may be routed in variable intensity to feed two filters.

You may regard the A-138s as a smaller version of the A-138m Matrix Mixer.

Inputs and outputs are DC coupled, i.e. the module can be used for the mixing of control signals too.

- 3U Eurorack module, 8 HP wide, 30 mm in depth
- Power consumption: 10 mA at +12 V and 10 mA at -12 V

Notes: A solid gold modern classic from FMR. The RNC must be one of the biggest studio bargains around. Proper analogue compression with digital control, offering pro sound at an affordable price.

Supplier's Notes:
What It Is

FMR Audio's first product, introduced over 18 years ago, the Really Nice Compressor (RNC) is a compact and cost-effective stereo compressor with a high-fidelity audio path and compression scheme. The RNC provides quality compression at a budget price.

How It Sounds

The RNC provides two modes of operation. One allows the RNC to be used for special effects, like snappy snares or popping basses. The other provides near-invisible signal compression for sensitive material where compression artifacts are less desirable (like natural vocals, acoustic guitar or the program bus). The RNC yields clean, airy compression with few artifacts and little high-end loss, even at massive gain reduction! The amazing performance is why- even after almost 20 years- many professionals are calling the RNC one of the best sounding compressors for under $2000.

How It's Done

The RNC achieves such high performance at a low cost by using using a microprocessor to replace discrete sidechain components (resistors, diodes, capacitors, opamps, transistors, etc) with chunks of software, thereby reducing the component cost. This approach, however, still processes the main audio in the analog domain, avoiding the problems associated with digital audio conversion (e.g., latency, digital artifacts). Even the problem of "scratchy" pots and switches are avoided: no audio flows through the front-panel controls. The front-panel pots and swtiches merely feed DC voltages to the microprocessor and it takes care of adjusting parameters and signal path with components - like sealed-relays and VCAs - located close to the input/output jacks avoiding noise pickup and audio quality reduction due to aging controls! With this blend of technology, the RNC offers the accuracy and precision of digital control with the clean tonal character of an all-analog signal path. The RNC's digital control permits accurate repeatability of your favorite settings.

Notes: 3xMIA is a 6-channel attenuverting mixer/offset/scale/polarizer.

3 blocks of 2-channel attenuverting mixers, using dual concentric pots. Each channel can be switched to mix with the subsequent channel, allowing for 2-2-2, 4-2, 6 mix configurations.

With nothing plugged into an input, an offset is normalled to that channel. The inner knobs control the A inputs, while the outer knobs control the B inputs.

DC coupled, so it can be used for audio, CV, or both at the same time.

80 mA +12V
80 mA -12V
35 mm Depth
6 HP wide

Notes: Updated version of the ground-breaking synth, sampler and sequencer. Better than ever, with legendary sound quality and portability.

Supplier's Notes:
The beauty of evolution.

Louder, thinner and 100 times better.

Introducing the all new OP-1 field. Injected with more than a decade of ideas, refinements and improvements. Just to mention a few: stereo throughout the whole signal chain, Bluetooth MIDI, USB type-C, a new speaker system with a passive driver for detailed, fat and loud sound, a massive 24 hour battery life, multiple tapes and recording formats, new great sounding reverb and the 'dimension' synth engine, an all glass, flush, high resolution display. The graphics have also been meticulously reworked, screen by screen.

Reworked, refined, reborn.

Think of OP-1 field as the natural continuation of its predecessor. Updated with the latest technology, improved design and finely tuned with professional musicians, recording artists and sound designers in mind. Higher quality in all aspects, from its circuitry to connectivity and flexibility, it's tailor made for professionals in the field.

The new stereo sample engine is just one of the features that takes the OP-1 field to a higher level. With increased sampling time up to 20 seconds and dual layer mode for instant mixing of the a and b channels or via an assigned LFO.

Four new recording formats: Studio 4-track, vintage 4-track, porta and disc mini.
All with their own unique characteristics and graphics. Now with multiple tapes or discs, up to 8 in total.

If it feels thinner, it is.

By lowering the aluminium body around the keyboard, the new OP-1 field feels lighter, thinner and more precise. with 2k moulding Teenage Engineering have also managed to fit a dual 2.4 GHz antenna system inside the aluminium body.

The back is warm, velcro and bass.

Two soft velcro rings have been added on the back for fastening covers and accessories. Perhaps you want to stick your op-1 field on top of your full size keyboard, or slap it on a guitar? Use the included adhesive looped back and start experimenting. On the right you'll find an additional passive loudspeaker for hugely improved bass. And for a 'no-more-cold-metal-on-your-lap' experience, the aluminium body has been folded in a warm, soft touch, hard cover.

The first accessory out using the velcro rings is the Bill Amberg leather wrap that attaches to the back and wraps around the op-1 field and locks around the encoders.

Dimensions: 28.8 cm x 10.2 cm x 2.9 cm

Notes: 4ms blank panel - 1HP width. Black coloured PCB material with 4ms logo.

Notes: - 2 x 2.1mm power plugs
- Power up to 2 Pedals

Notes: ZED-6FX delivers Allen & Heath's renowned build and audio excellence in a compact, portable format, making it the ideal choice for quality conscious musicians, singer / songwriters and venues. Whether it's bouncing ideas around at home, performing live or recording tracks to share on YouTube and Soundcloud, ZED-6FX is a versatile companion for every step of the creative journey. Featuring the new GSPre boutique preamp design, developed from the revered GS-R24 studio recording console, the ZED boasts exceptionally low noise and massive headroom, with a signature analog warmth and depth. ZED-6FX is the first mixer to include a specially created suite of studio quality reverbs, delays and special multi-model FX, crafted by Allen & Heath's acclaimed in-house effects aficionados. Guitarists will be pleased to know that ZED-6FX comes with a pair of Guitar DI high impedance inputs, allowing guitars to be plugged straight into the mixer without the hassle and expense of carrying separate DI boxes.

ZED-6FX features an exceptional new preamp design, created by analog guru, Mike Griffin and developed from his highly acclaimed GS-R24 studio recording console. Known as GSPre, the preamps deliver exceptionally low noise and massive headroom, and the warmth and depth that Allen & Heath's analog range is famous for. For tonal shaping, the precise MusiQ EQ controls have been carefully calibrated for responsiveness and precision, making it easy to shape and enhance each musical source.

ZED-6FX boasts a brand new suite of studio quality reverbs and delays, painstakingly crafted to enhance your recordings and performances. Special multi-model effects provide uniquely dynamic combinations of reverbs and delays.

All ZED mixers are designed and built to Allen & Heath's legendary touring grade standards to ensure a long life in the toughest environments. All channels are on individual, vertical circuit boards and all rotary controls are secured to the front panel with a steel nut to guard against impact damage.

ZED-6FX comes with two Guitar DI high impedance jack inputs, allowing guitars to be plugged straight into the mixer without the need for DI boxes. That's one less piece of gear to buy, carry and set up.

Allen & Heath has been a trusted name in professional audio since 1969. The ZED technology advances, but the commitment to audio excellence and build quality endures.

Notes: mioXC - The USB Type-C 1x1 MIDI interface for Mac, PC, iOS, or Android

Tiny in size and price, yet big on connectivity! mioXC is a pocket-sized powerhouse! mioXC is a fuss-free and simple 1x1, 16 channel MIDI interface you can use to connect your MIDI compatible gear. Whether you have a controller keyboard, synthesizer, drum machine or whatever; mioXC lets you connect them to your Mac, PC, iOS, or Android computing device.

What Makes mioXC Unique?

Even the most basic tasks need to be done right; it's surprising how many of iConnectivity's competitors' interfaces get it wrong. mioXC has been engineered, from the ground up to, to be the interface that its manufacturers would want to use themselves.

Modern USB Connectivity - Equipped with both USB Type-C and USB Type-A connectivity, mioXC lets you enjoy easy connectivity with most modern computing devices.

Driver Compatibility - Interfaces that use their own drivers have to be updated all the time, or they stop working properly. Likewise some designs were USB Class-Compliant years ago, but today they aren't anymore. iConnectivity's drivers have been engineered to today's strict guidelines, and keep them updated, to ensure compatibility for years to come.

MIDI Management - iConnectivity interfaces deliver MIDI reliably no matter what. When the MIDI data-stream gets heavy, these interfaces plough on where other interfaces choke.

Rock-Solid Electrical Design

- Some MIDI interfaces introduce noise, or worse, crash your system. You'll never get that from an iConnectivity interface.

Performance Optimized - A MIDI interface that works too slowly is useless. mioXC uses a powerful 32-bit ARM Cortex processor, ensuring dense MIDI and SysEx streams are managed with ease.

The iConnectivity Advantage: iConnectivity's name on your interface means that time was taken to do it right, whether it's the simple 1 x 1 models to iConnectivity's uniquely sophisticated high-end interfaces.

What's in the box
One mioXC MIDI Interface.
One USB Type-C to USB Type-A adapter

Macintosh
Mac OS X
1 free USB port

Windows
Windows 7 or later
1 free USB port

iOS
iOS 8 or greater*
CoreMIDI compatible app
*Apple Lightning to USB Camera adapter required for use with Lightning equipped iOS devices (adapter not included)

Android
Android 8.0 or higher with USB-C connector

Notes: Custom engineered in the UK for the Empress Effects Zoia Effects Pedal, Decksaver's super durable polycarbonate shell protects against dust, liquid and accidental impact. Precision trimmed for an exact fit whilst accommodating cables, your MPC can sit ready for operation. Slides straight into a flight case or bag ready for transportation. Shields delicate controls and internal components from damage at home, on the road and on stage.

Notes: The Ultimate Eurorack Utility Module (and a whole lot more!)

The DATA is a digital platform for testing, measurement, and signal generation in Eurorack modular synthesis systems. It is a modular tool kit, with functions applicable to any system and style.

Use the DATA's scope to view the interactions between your control voltages and audio signals, allowing you to master your modules by understanding their voltage ranges, control shapes, and parameter responses. Use the DATA's dual waveform generator to dial in a precisely scaled LFO for CV control, or use the waveform's frequency "note mode" to effortlessly make dyads (two note chords). Use the DATA's clock program as a master clock or to divide or multiply an incoming clock signal, sending four different clock outs to gate modules directly or as control to sequencers.

The possibilities of the DATA are basically unlimited; with the included microSD you can update the DATA's firmware and we can continue to refine and create new programs.

Notes: Custom ALM patch cables. Small but strong, they are designed for maximum ergonomic post modern wiggling.

- 15cm (Pack of 5)
- Colour: Yellow

Notes: Pack of high Quality patch cables. Not too stiff, not too loose!

One colour for each size make Befaco patch cables just perfect to keep them organized!

This pack contains 3 high quality blue patch cables.

Notes: The Whammy Ricochet lets you bounce your playing up or down in pitch in controlled or crazy shifts. A momentary switch and customizable independent rise and fall time ballistics, allow you to get the Whammy action you know and love without the use of a treadle. Just hold your foot on the footswitch and let the Ricochet do the rest. Seven pitch selections - 2nd, 4th, 5th, 7th, Octave, Double Octave, and Octave+Dry, as well as a toggle to select up or down for the selected pitch. The Whammy Ricochet also has latching footswitch mode so you can rise or fall to pitch and stay there, and an LED ladder that shows your shift trajectory at all times. All these controls combine to create classic Whammy pitch-shifting as well as new sounds never heard before.

General Specifications
ControlsBallistics Control, Pitch Control, Range Switch, Momentary Switch, Effect On/Off
Sample Rate44.1 kHz in classic mode, 22 kHz in chords mode
Frequency Response20 Hz-16 kHz (classic mode), 20 Hz-11 kHz (chords mode)
Signal to Noise Ratio> -106dB (A weighted); ref = max level, 22 kHz bandwidth
A/D/A Converter24-bit
THD0.004% @ 1 kHz; ref = 1 dBu w/ unity gain
Power Consumption2.1 Watts (235 mA typical @ 9 VDC)
Power Requirements9 VDC External Adapter (sold separately)
Power SupplyPS0913DC-01 (US, JA, EU); PS0913DC-02 (AU, UK)
Power Adapter Output9 VDC 1.3 A
Dimensions
Length4.75"
Width2.875"
Height1.75"
Weight0.8 lbs.
Audio Output
Output1/4" Unbalanced (Tip-Sleeve)
Max Output Level+10 dBu
Output Impedance1 kO (Effect enabled or effect bypassed w/ Momentary switch on) True Bypass (Effect bypassed w/ Momentary switch off)
Audio Input
Input1/4" Unbalanced (Tip-Sleeve)
Max Input Level+5 dBu
Input Impedance1 MO (Effect enabled or effect bypassed w/ Momentary switch on) True Bypass (Effect bypassed w/ Momentary switch off)

Notes: Protect tomorrow's future classics, today!

The ISLA Instruments S2400 is a 21st Century homage to one of the electronic music world's most iconic drum samplers - the SP1200.

Dust, liquid and accidental impact have taken many a good analogue drum machine down over the years - and this is where Decksaver steps in.

Designed to mould perfectly around the outer case of the unit and precision trimmed for a superb finish, whilst accommodating cables at the rear, the S2400 can sit ready for operation.

Slides straight into a flight or soft case for maximum protection during transportation.

Shields delicate faders, knobs and internal components from damage at home, in the studio, or on the move.

Dimensions:

Weight: 0.8kg
Length: 45cm
Width: 30cm
Height: 4.7cm

Notes: The Nano Pulsar takes tremolo beyond the ordinary and mundane. Equipped with a collection of tremolo-modulating waveforms and the option of operating in Triangle or Square Wave modes, the Nano Pulsar is a tremolo/panner treasure chest. In mono, it's simply amazing, or, connect it in stereo to create shifting waves of sound that surround you and fill your space with weaving, pulsating energy.

For all its power, the Nano Pulsar's layout is intuitive and using it is easy. There's often a perceived volume drop with tremolo when the effect is engaged so we've included a Volume control. It allows a player to fine-tune their output level when the effect is on, and is a very useful addition.

The Nano Pulsar's Depth knob adjusts the amount of tremolo applied to the signal. Past maximum (around 1 o'clock) the modulation becomes asymmetric and warps the audio signal between positive and negative phase. This creates a unique style of tremolo which sounds great alone or can be used in combination with other effects like the Oceans 11's Shimmer patch to produce compelling synth-like sounds and textures.

The Rate knob provides a full range of speed adjustments for the tremolo or pan effect, and when you start to max out the Rate and Depth controls you enter ring modulation territory for a surreal sonic joyride!

Unlock a world of advanced sound shaping and control. Create tremolo and panning effects that go from sublimely beautiful to downright shocking. The compact Nano Pulsar will be your do-it-all, go to pedal for all things tremolo and panning.

Specifications

Circuit: Analogue
Bypass: Buffered Bypass
Audio: Stereo Out
Power Supply: 9V battery included (optional 9.6VDC-200mA power adapter not included)
Dimensions (in): 4.5 x 2.75 x 2.1
Current Draw: 30mA

Notes: Wireless version of AIAIAI's outstanding studio headphones. Wireless+ technology allows lossless streaming with ultra-low latency. Usual stylish modular approach and quality build.

Supplier's Notes:
Empowering music creators with the freedom to create wirelessly. The TMA-2 Studio Wireless+ is a versatile professional headphone, designed for today's dynamic creative workflow. Featuring new W+ Link technology for ultra-low latency and uncompressed audio, added Bluetooth 5.0 with +80 playback, and a coiled hi-fi cable.

Wireless music creation with ultra-low latency and uncompressed audio with W+ Link technology.

Uncompressed and robust 16ms latency connection for high quality wireless audio designed for enhanced freedom and creativity.

Extended versatility with added Bluetooth for +80h playback and hi-fi coiled cable.

Seamlessly switch to Bluetooth 5.0 with +80h playback for everyday listening and inspiration, and a coiled hi-fi cable included for a traditional connection.

Signature AIAIAI bio-diaphragm speakers tuned for clarity and detail. Critically acclaimed sound stage specifically designed for music creation with a clear and highly detailed sound representation.

Enhanced comfort with Alcantarar over-ear memory foam cushions. Soft over-ear memory foam cushions covered with resilient, CO2 neutral, and highly comfortable Alcantarar, ideal for longer sessions.

Responsible modular headphones - designed to last. Upgrade and expand as technology or needs evolve to extend the functional lifetime of the product and create less waste for the planet.

Specifications

Speaker unit

Driver diameter: 40 mm.
Sensitivity: 97 dB @ 1mW.
Rated power: 40 mW.
Max power: 100 mW.
Diaphragm: Bio-cellulose.
Magnet: High grade neodymium.
Resonance freq.: 80 Hz.
Impedance: 32 Ohm

Transmitter

W+ Link audio quality: Lossless.
W+ Link latency: 16 ms.
Operating range: 12 metres.
Playback time: 30 hours.
Charging time: 3 hours.
Battery: 2700 mAh.

Headband

W+ Link audio quality: Lossless.
W+ Link operating range: 12 metres.
Bluetooth version: 5.0.
Charging time: 2 hours.
W+ Link latency: 16 ms.
W+ Link playback time: 16 hours.
Bluetooth operating range: 10 metres.
Battery: 970 mAh.
Bluetooth codecs: AAC, SBC.

Notes: Mains Power Leads UK - IEC 10A

UK 3 pin plug to IEC C13 female plug 3 cores mains power lead, suitable for connecting power to general electronic equipment up to 2300W (10A).

Max. current: 10A
Max. power: 2300W

Notes: Arturia MiniFuse 1 is a portable 1 in / 2 out audio interface audio interface designed to work for you, whatever your style. Record your vocals, guitar, podcast, or produce your track at the highest studio quality. A complete software bundle with instruments, recording software, and effects is included - recording and producing has never been easier.

MiniFuse comes from the award winning Arturia AudioFuse line of studio audio interfaces. Class-compliant & Bus-powered means you can plug in and go, and you won't need an additional power supply as it's USB powered. Recording has never been easier.

MiniFuse 1 fits right into your setup with a straightforward set of ins and outs. Its single combo input lets you easily connect either XLR or 1/4" jack cables. Plug into your computer with quick & compact USB-C compatibility. Finally, connect USB devices like your MIDI keyboard with the additional USB hub socket.

For audiophiles, MiniFuse boasts a 110db dynamic range and a class-leading equivalent input noise of -129dB. For everyone else, that means that every recording you make sounds incredible, with rich dynamics, clear noise-free signal, and studio-grade quality - you can't go wrong.

Break the mold and take your studio on the go. MiniFuse is not only compact and lightweight; its rugged aluminium casing can handle the mobile producer's lifestyle. Put it in your bag, get out there, and find the sound you've been looking for.

Whether you're using a laptop or desktop, MiniFuse can work for you. PC or Mac, connect it and enjoy total recording freedom. Better still, with the MiniFuse Control Center app, you can control its inputs, outputs, settings, and firmware updates in one place

Keep your creativity fresh and your inspiration flowing with step-by-step music production tutori-als, mixing hacks, and Ableton project templates designed by artists, producers, and beatmakers, featuring the software that's included with MiniFuse. Updated frequently, no subscription re-quired, and free with your MiniFuse. MiniFuse comes with an exclusive selection of software titles offering everything you need to give your sound the professional edge.

Arturia FX

Colour your sound with 4 premium FX plugin recreations of studio classics; a lush plate reverb, a gritty analogue preamp, a classic tape echo, and a rich stereo chorus.

Ableton Live Lite

Compose, record, perform, and produce anything with an introduction to one of the most widely-used musical software titles in the business - yours with MiniFuse.

Analog Lab Intro

Instantly add inspiring sounds from Arturia's award-winning keyboard emulations to your mix with hundreds of presets to explore, from vintage '80s synths to fat modern sounds.

Auto-Tune Unlimited 3-months free subscription

Refine your vocal parts for perfect harmony or go full trap-style autotune with a 3-month sub-scription to the industry's favorite voice tuning plugin.

GUITAR RIG 6 LE

An inspiring selection of amps, cabs, delays, reverbs, stompboxes and compressors, so you can build your own processing chains and customize your perfect guitar tones.

Splice Creator Plan

3-months free subscription Access millions of hi-def royalty-free samples and plugin presets, from lo-fi drum loops to punchy vocal one-shots, and add them to your personal collection for life.

Huge software bundle includes: Ableton Live Lite, Analog Lag Intro, 4 x Arturia FX, Auto-Tune 3-month subscription, GUITAR RIG 6 LE, Splice 3-month subscription, and more...

Included Software

Ableton Live Lite: For your recording and mixing needs

Analog Lab Intro: Classic and modern synthesizer and keyboard sounds

4 x Arturia FX: A world-class preamp, plate reverb, tape echo and chorus effects

Auto-Tune Unlimited: 3-month subscription to the leading pitch tuning software

GUITAR RIG 6 LE for guitar amplification emulations and guitar

Line Inputs
Input impedance: 16kO
Maximum input level: +22dBu
Gain range: 56dB
Frequency response 20Hz to 20kHz: +/-0.05dB (min gain)
Dynamic range: 110dB typical (A-weighted)
THD+N @ 1kHz: -100dB typical (un-weighted)
Instrument Input
Input impedance: 1MO on Tip
Maximum input level: +11.5dBu
Gain range: 56dB
Frequency response 20Hz to 20kHz: +/-0.06dB (min gain)
Dynamic range: 110dB typical (A-weighted)
THD+N @ 1kHz: -91dB typical (un-weighted)
Microphone Preamps
Input impedance: 2.5kO
Maximum input level: +9dBu
Gain range: 56dB
Equivalent Input Noise (EIN): -129dB typical (A-weighted)
Frequency response 20Hz to 20kHz: +/-0.06dB (min gain)
Dynamic range: 110dB typical (A-weighted)
THD+N @ 1kHz: -100dB typical (un-weighted)
Speakers
Output impedance: 94O
Maximum output level: +12dBu
Frequency response 20-20kHz: +/-0.09dB
Dynamic range: 107.5dB typical (A-weighted)
THD+N @ 1kHz: -101dB typical (un-weighted)
Phones
Output impedance: 10O
Maximum output level: +11.4dBu
Frequency response 20-20kHz: +/-0.09dB
Dynamic range: 104dB

Notes: Rigid, 2mm aluminium powder coated and 300mm wide studio cable holder can host over 80 studio cables in perfect order! Two screws for fixing the cable holder are included.

Notes: Two units of the 6-way Squid multiplier cable.

Notes: Fully redesigned from the original Cosmix, the Cosmix Pro is an eight-channel mixer intended to work nicely for performance as well as production. Suitable for line-level stereo signals as well as Eurorack levels.

Supplier's Notes:
A completely new design, with a lot of attention to sound quality, with a clean, low noise signal path, and lots of headroom.

It features the same amount of channels as the previous Cosmix, 4x mono in, and 2x stereo in.

There's one mono aux bus, and an additional true stereo AUX for all channels, with a dedicated mono and stereo return.

Each channel has a pan pot, a big push button for clickless muting, and a dedicated LED level meter to visualize channel output level.

The mono channels come with a handy low cut switch. (-3dB @80Hz / -6dB @ 45Hz)

The stereo channels have an optional +18dB gain, allowing you to easily mix in line level external gear.

The two stereo channels also have a CV input for voltage controlled panning.

There are connectors on the back for daisy chaining, or for connecting to future expanders/other mixer units.

High quality aluminium panels, available in black or silver.

The older model Cosmix is discontinued until further notice, since the parts for the drive circuit are unobtainium.

That's also the reason there is no dedicated drive circuitry in the new model.

Technical specs
22HP, 20mm deep.
+12v: 170mA, -12v 170mA

Notes: Mantis have taken years of experience with Eurorack to create a low-cost case that makes the Eurorack modular synthesizer look, work, and feel like a professional instrument. Mantis is an instrument that is at home on stage, touring, or in the center of the studio.

Mantis has two rows of 104HP for you to rack your modules. It comes fully powered and assembled, just drop in your modules and play.

Using its sophisticated leg mechanism, you can set it to three different positions: 0, 45, and 90 degrees.

Power Power and more Power! With Mantis, say bye-bye to the tedious, never-ending calculation of current consumption for the i12V power. Mantis comes with a juicy Zeus power supply that delivers plenty of power both now and for the future.

Mantis deep black coloru gives you another option to customize your Eurorack look and matches perfectly with black Tiptop Audio modules.

Mantis comes with real Z-Rails made according to Eurorack enclosure standards. No sliding nuts or wrong spacing! It also has keyed power connectors to help protect your modules from damage from plugging the power in in reverse.

Weighing only 3kg/6.5lb, Mantis is so light, traveling has never been so relaxed.

Dual Mantis Studio Brackets

Using the optional bracket accessory Mantis can be doubled up to 416HP! Multiply your Mantis and watch your studio setup grow.

Notes: Bucket brigade delay gets pushed into exciting creative territory with this beauty from Joranalogue. Precise analogue delay with loads of character, capable of simple chorus and flanger or more exotic Karplus-Strong synthesis and comb filtering.

Supplier's Notes:
While digital audio processors are often plagued by latency issues, analogue circuits are known for their instant response. But what if you want to delay a signal on purpose, without the use of tape or digital memory? Enter the bucket brigade delay (BBD) line: a series of capacitor 'buckets', which pass the incoming signal along at a high rate in order to delay it.

Delay 1 is a fully analogue BBD-based delay module with a multitude of features geared towards modern musical use. An integrated temperature-compensated, high-frequency voltage controlled oscillator (VCO) provides the 'clock' signal necessary to drive the delay line within 1 to 50 ms.

By increasing the drive frequency to over 20 kHz, the classic 'BBD clock whine' problem is solved, while still providing a wide range in delay time. Classic chorus, flanger and echo effects are easily achieved using the dry/wet blend, feedback and damping parameters.

To greatly reduce distortion and noise, Delay 1 includes a newly developed control circuit. The improved fidelity is maintained at a multitude of signal levels by an integrated high-performance compander, while maintaining signal dynamics.

The module's 'split phase' topology provides two different dry/wet mixes, which may be used to convert mono signals to stereo, for complementary comb filtering and more.

Delay 1 also allows you to experiment with Karplus-Strong synthesis, an exciting technique to create string and percussion type sounds. This is made easy by an integrated noise transient generator, driven by the 'pluck' input, and by the clock VCO's 1 volt per octave response.

By re-engineering the classic analogue delay line, Delay 1 brings the unique magic of BBDs into the contemporary electronic musician's arsenal.

Analogue bucket brigade delay line.
Integrated temperature-stable high-frequency BBD clock VCO with fine and coarse tuning.
Split-phase topology with additive and subtractive dry/wet blend outputs.
Blend, feedback and damping (feedback filter) parameters. Positive or negative feedback with low or high pass filtering.
High-performance BBD drive circuitry and transparent compander chain ensure optimal signal fidelity.
Dedicated pluck trigger input for Karplus-Strong synthesis.
High-frequency BBD clock input and output to synchronise multiple delay lines.
Impedance-compensated outputs with dual-colour LEDs.
Trim potentiometer accessible from the front panel.
Premium mounting hardware: black screws, black nylon washers and matching hex key.
High-quality components and assembly; designed and made in Belgium.

12 HP | +12: 125 mA, -12: 95 mA

Notes: As a stand-alone instrument, Mavis is a straightforward analogue synthesizer with patchable modular utilities and the unmistakable Moog sound and quality. Easily remove Mavis from its case and it becomes a 24-point CV controllable module (44hp) ready to be installed into your Eurorack system or alongside Moog's other semi-modular instruments.

Mixing the familiar with the exotic, Mavis features Moog's legendary oscillator and filter circuits alongside a diode wavefolder - the first analogue wavefolder to appear on a Moog instrument. Combining traditional subtractive synthesis with additive wavefolding and oozing with personality, Mavis' clever presentation of synthesis modules and utilities ensure deep creative synergy and musical connection.

Mavis is a powerful, fun, and low-cost Moog that makes learning synthesis or expanding an already-advanced studio setup approachable for anyone looking to explore classic analogue sound in a new way.

Get closer to the circuits at the heart of Mavis and come away with a Moog analogue synthesizer that is uniquely "yours". No soldering is required and can be completed by any skill level in an afternoon.

A powerhouse on its own, Mavis was also designed to enhance any interconnected Moog semi-modular setup or Eurorack system. In 44HP, the synthesizer offers incredible value with two oscillators, full ADSR, ladder filter, sample and hold, wavefolding, attenuators, mixer, mults, and much more for more complex musical arrangements.

Mavis is eager to play along with other voltage-controlled devices (especially with Moog's other semi-modular instruments), and its useful collection of utilities and flexible control voltage routing allows for intricate dialogue between them.

Built-in keyboard with Glide and KB scaling

As a standalone instrument or as a 44HP Eurorack module, Mavis adds an expressive 1 v/o controller to any setup with the flexibility to dial in experimental new pitch relationships via the KB scale knob and explore musical intervals that go beyond the established standards.

Full Range Analog Oscillator

A Voltage Controllable Oscillator with PWM (Pulse Width Modulation), Waveform mixing, and Mod Source mixing, delivers rich harmonic character and motion.

Voltage Controlled Filter

Sculpt your sound with the -24-dB Moog Low Pass Ladder Filter, delivering the sonic power behind the distinct sounds of Moog basslines and leads.

Audio Rate LFO and 4-Stage Envelope Generator

Mavis uses crossfaders in its modulation routing instead of switches, allowing you to blend between a variable shape LFO and four stage envelope generators for interesting and unusual modulation contours.

Wavefolding and Modular Utilities

Mavis features Moog's first-ever wavefolding circuit, allowing for additive synthesis to sit alongside traditional subtractive synthesis, unlocking sounds not heard from a Moog before. Mavis also features a broad modular utility section complete with attenuators, offsets, mults, and a flexible DC-coupled mixer providing the tools needed for creative patching and sound design.

Patchable Sample and Hold (S+H) circuit:

Generates a random CV pattern that can be patched to modulate other parameters, including setting Mavis into a "random sequencing" mode of performance.

24-Point Patch Bay

Mavis is eager to play along with other voltage-controlled devices (especially with Moog's other semi-modular instruments), and its useful collection of utilities and flexible control voltage routing allow for intricate dialogue between them.

Protective Cover

Mavis includes a fitted protective cover for use during studio downtime or taking your instrument on the go.

Specs

Type: Semi Modular Analog Synthesizer - Operate standalone or as 44hp Eurorack module
Polyphony: Monophonic
Keypad: 1 Octave Keypad w/ Glide and Scaling
Sound sources: Analogue Voltage Controlled Oscillator (Mixable Saw/Square)
Filter: Analogue -24dB Moog Low Pass Ladder Filter
Envelope: 4-stage Analog EG (Envelope Generator)
Wavefolder: Diode Wavefolder
LFO: Analogue LFO (Mixable Triangle / Square)
Modular utilities: Sample and Hold, Attenuators, Offsets, Mults, and a flexible DC-Coupled Mixer
Patch bay: 24-Point Patch Bay (3.5 mm)
Accessories: Protective Cover, Patch Cables, Calibration Tool, and Nut Driver Included

Notes: Arturia's new KeyLab Essential 3 offers a new level of accessible, enjoyable, and creative music making, redefining the essence of a modern universal keyboard controller.

From its refreshing new design, to its vastly upgraded creative workflow, to an expanded software package, it promises to shake up the affordable controller market by empowering modern musicians and sound explorers looking to expand their setup without breaking the bank.

Main selling points

Fit for any style and any setup

For DAW producers, musicians with hybrid setups, or performers using hardware; enhance any creative setup or musical style with MIDI out & USB power, deep DAW compatibility, and premium software.

The new standard for affordable keyboard controllers

A keyboard controller that doesn't need tons of controls, menu diving, or complex configuration to operate. KeyLab Essential 3 looks modern, feels great, and removes creative barriers for next-level music making.

Directly-linked with Arturia's industry-leading software ranges

Many musicians and producers will be familiar with Arturia's award-winning software; KeyLab Essential 3 is part of the same range, seamlessly integrating with Analog Lab V, Pigments, and V Collection.

Features

Premium Keybed quality
49 note velocity-sensitive keyboard with hybrid synth-piano feel

Pads & controls
1 clickable encoder
9 rotary encoders
9 x 30mm faders
8 transport switches
4 command switches
1 modulation wheel & bend wheel
8 touch & pressure-sensitive pads

Display control
2.5" LCD display with contextual buttons
Real-time feedback on tweaks and controls
Smart features

Multi-mode arpeggiator
Chord mode
Scale mode
Hold function
Semitone transpose

Software integration
Seamless integration with Analog Lab V: select sounds, browse presets, smart-assigned controls
Custom DAW scripts for FL Studio, Logic Pro, Ableton Live, Cubase, Bitwig Studio
Also compatible with MCU/HUI control
Up to 6 user presets for a totally customizable experience

Included Software titles & services
Analog Lab V software with 2000+ sounds
Ableton Live Lite
Native Instruments' The Gentleman
UVI Model D
2-month Loopcloud subscription
Melodics subscription for 40 lessons

Connectivity
USB-C connects to computers and MIDI Control Center
MIDI 5-pin DIN output for connection to external instruments, gear
Control input for pedal: sustain, expression, or footswitch
USB-C powered

Platform specifications

Windows
Win 10+ (64bit)
4 GB RAM
4 cores CPU, 3.4 GHz (4.0 GHz Turbo-boost)
3GB free hard disk space
OpenGL 2.0 compatible GPU
ARM processors not supported on Windows

Required configuration
Works in Standalone, VST, AAX, Audio Unit, NKS (64-bit DAWs only).

Apple
Mac OS 10.13+
4 GB RAM
4 cores CPU, 3.4 GHz (4.0 GHz Turbo-boost) or Apple Silicon CPU
3GB free hard disk space
OpenGL 2.0 compatible GPU
Work with ASC
An elegant and simple solution to help you install, activate, and update your Arturia software instruments.

What's in the box

Box content:
KeyLab Essential Unit
USB-A to USB-C cable
Registration card

Dimensions for 49 keys
Size : 31.1 x 9.45 x 2.76 inches (790 x 240 x 70mm)
Weight : 6.1 lbs. (2.76 Kg)

Notes: The 1010music line of stereo breakout cables are designed to connect 2 mono audio signals to a single stereo TRS 3.5 mm minijack plug. The slim caps fit side by side with other cables in compactly spaced input jacks, like those on the 1010music bluebox. These cables may have been designed for the bluebox, but they have a wide variety of uses with other gear as well.

Each of these cables has a male TRS stereo 3.5mm minijack plug on one end and two male TS mono 3.5 mm minijack plugs on the other end. They are 1.4 m/4.5 ft long with the 1010music logo printed on the plug caps.

This stereo breakout cable connects two 3.5mm male mono TS minijack plugs to the left and right channels of one 3.5 mm male stereo TRS minijack plug. Red and black end caps on the split end differentiate the left and right channels. Each cable is 1.4 m/4.5 ft long and has slim metal caps with the 1010music logo on all plugs.

Specifications:
1.4 m/4.5 ft long
one 3.5 mm male stereo TRS to two 3.5 mm male mono TS
Nickel / 24K Gold plated connector
Highly flexible PVC / TPE Jacket Materials
Rohs, UL, CE, and FCC approved

Notes: Save space in your rack with stackable cables.

These are the newer shorter stackable Eurorack Patch Cables. Patching is more stable and makes it easier to get a lid on that performance case.

Each end of the cable has a male and female jack. They come in sets of 5 cables.

Available in 6in (15cm), 12in (30cm), 18in (45cm), 24in (60cm).

Notes: This is a buffered/active mult with LED indicator. You get two channels of 1 to 3 multiples within a 2HP module. The output of channel 1 is normalled to channel 2 so it can also be treated as a 1 to 6 multiple as well.

Active vs Passive mults:

With a passive mult you are effectively just plugging multiple things into the same jacks. This will often cause some voltage drop in each of the signals. With an active (or buffered) mult you will not get any voltage drop from the original signal.

Comes with a black and gold panel, power cable and one year warranty.

Usage note:

The red stripe of the power ribbon cable goes towards the top of this module.

Notes: Welcome to the world of sound of LYRA-8, the unique organismic analogue synthesizer designed by Vlad Kreimer. "Organismic" means that LYRA uses some principles that lie in the base of living organisms. The way how LYRA's modules interacting between each other and the behaviour of the instrument resembles a live conversation.

LYRA-8 is based on eight generators, which will be referred to as voices. Their design is not like a traditional subtractive synthesis VCO. Instead of having a linear or logarithmic dependency on control voltage, they resemble the tone generators in old electric organs. Hence the use of the term "voices" instead of "VCOs". Lyra uses non-linearity a lot, and the voices are constructed in such a way that allows for non-linearity to express itself.

The voices are divided into four pairs (12, 34, 56, 78). All the pairs are divided in two groups, with two pairs in each (1234, 5678), creating tree-like structure.

The voices can function either in an electric organ mode or in an FM synthesis mode with each of the voices and its envelope acting as a separate FM operator. The voice's impact on FM synthesis will decrease along with the decay of its envelope.

LYRA-8 also has the next blocks:

The HYPER LFO is a complex low-frequency generator, whose waveform is synthesized from two simple LFOs by summation or multiplication of their frequencies. It also has a sync mode. The LFO can modulate the selected pairs of voices and the MOD DELAY.

The MOD DELAY consists of two lines of delay with cross-feedback and a special architecture that enables resonance between the two lines. Each line's delay time can be individually modulated from various sources, including external ones. The delay has a unique possibility of self-modulation where the output signal modulates the delay sample rate, creating cool effects.

The DISTORTION is last in the chain, after the delay. It enables the delay to also influence the distortion.

For all its experimental character, LYRA is a professional instrument. Its output dynamics and frequency response are balanced and ready for a live performance or studio recording without any additional processing.

Notes: 3xMIA is a 6-channel attenuverting mixer/offset/scale/polarizer

3 blocks of 2-channel attenuverting mixers, using dual concentric pots. Each channel can be switched to mix with the subsequent channel, allowing for 2-2-2, 4-2, 6 mix configurations.

With nothing plugged into an input, an offset is normalled to that channel. The inner knobs control the A inputs, while the outer knobs control the B inputs.

DC coupled, so it can be used for audio, CV, or both at the same time.

80 mA +12V
80 mA -12V
35 mm Depth
24HP wide

Notes: The compact and complete VCA. Filtering and mixing rolled into one powerful unit. The Dreadbox Eudemonia Filter is an analog wave generator processor. It provides accurate mixing capabilities and features a dual filter in series. The filters are a 24dB resonant Low Pass Filter and an 18dB non-resonant High Pass Filter - these allow you to shape your sound before sending to your output. In order to keep things in line, the exponential VCA has a peak indicator to help you reference your levels.

Power Consumption: 61mA @ +12V , 69mA @ -12V
61 mA +12V
69 mA -12V
35 mm deep
10HP

Notes: Collabing with YouTube sensation Andrew Huang, Endorphin.es offer up this impressive multipurpose processor module. Building blocks of stereo filtering, compression, reverb and more offer huge creative potential.

Supplier's Notes:
In collaboration with Andrew Huang, based on his modern music production techniques, Endorphin.es developed a creative audio processor with multiple blocks that can be moved around in order to achieve different flavours for sound design.

Processing unit without fixed structure: intuitively create astonishing and ephemeral timbres, from atmospheric rumbles to heavy or distorted textures.
Creative stereo effect processor with delay, reverb, filter and distortion with quickly explorable routing chain with single button press.
New generation ARM Cortex - M7 processor with 96 kHz 32 bit internal processing.
Lush hall and whooshing reverse reverbs with audio freeze and pre-delay.
Sidechain audio ducking envelope available both internally and externally with additional one knob single band compressor.
Tap delay with maximum delay time up to 2.5 seconds, external clock input with onboard clock divider and 1v/oct time control.
8x oversampled distortion algorithm.
Pre- and post - VCA, tone and volume controls with extra gain.

Power consumption:
135 mA +12V
35 mA -12V
0 mA 5V

Dimensions:
16 HP
26 mm deep with power ribbon cable connected.