Studio Equipment charts

Notes: A typically unique take on multi-effects from Soma, designed to induce meditative states. Hybrid analogue-digital delay/reverb/granular processing gives a range of creative approaches.

Supplier's Notes:
COSMOS is a drifting memory station designed to work with meditative states through music. The design of the controls, functions and generated soundscapes are intended to evoke, in both performer and listener, states and experiences inherent in meditation, such as limitless space, fluidity, spontaneous development, presence, the ability to hear, tranquility, the experience of subtle harmony and happiness enveloping the whole world.

From a functional point of view, COSMOS is a large array of sound memory, in which recorded sounds undergo constant recombinations, spontaneously generating an ever-changing soundscape. This is achieved in three ways - by a mathematical shift based on the relationships between large prime numbers (the size of all delay lines are different primes), an asynchronous operation of the LFO, and modulation with a slowly changing chaotic signal. As a result, it allows the endless layering and processing of various sounds, as in a looper, but without an intrusive, repetitive loop.

COSMOS generates rich, fluid and evolving soundscapes perfect for ambient music. Using COSMOS, you can play an entire meditative solo concert while being in a spontaneous flow and without using studio-prepared sequences, backing tracks and other things that can't be a reflection of the "here and now".

Specifications

Minimum input voltage: 0.35 V peak-to-peak
Maximum output voltage at line outputs: 11.3 V peak-to-peak
The maximum output voltage at the headphones output: 10.4 V peak-to-peak
Frequency response: 10-22000 Hz
Sound memory: 44.7 sec
Supply voltage: 12 V *
Power connector polarity: centre plus
Current consumption: 0.25 A
Dimensions: 342 x 153 x 68 mm
Weight: 2.2 kg

* Use only the power supply supplied with the device! In case of failure, it can be replaced with a high-quality modern switched-mode power supply with an output voltage of DC 12 volts, the center is plus and an output current of at least 0.5 amperes (more is fine). The power supply must have a wide AC input voltage range of 100-240 volts. Such power supplies have excellent output voltage stabilization required for the device. It is forbidden to use COSMOS with nonstabilized voltage from transformer power supplies. It can lead to damage to the device, which is not covered by the warranty repair!

Notes: This MIDI Adapter enables you to connect MIDI devices that use standard MIDI cables to the stereo minijacks used by 1010music products. The adapter has a male stereo minijack at one end, and a female 5 pin DIN MIDI connector on the other, and is 22 cm/8.5" long. It is also useful as a converter for connecting to other MIDI devices that use a different mapping of MIDI signals to the stereo minijacks.

Notes: Set of 5 high-quality braided & soft 3.5mm patch cables for use with eurorack modules. The braided patch cables have a soft touch & are perfect for traveling with your eurorack system patched as they are super-bendable and much less likely to get tangled even with your case lid closed. Pleasant & practical for a better patching experience.

Notes: Balanced microphone/audio lead terminated at one end with an XLR socket and at the other end with an XLR plug.

Notes: High quality audio leads for exceptional sound quality and reliability. Twinned high grade cable comprises 2 insulated pure copper cores and global shielding.

The durable PVC sheath has a soft texture and is reinforced with cotton cord to avoid tangling.

Terminated at one end with a 6.3mm stereo (TRS) jack and at the other end with 2 x 6.3mm mono jack plugs.

Notes: IsoAcoustics introduce the next evolution of their specialized line of speaker stands for the audio professional, music hobbyist, audiophile, and music lover. The new ISO Series of speaker stands provide superior acoustic isolation and enhance the sound clarity of any speakers including studio monitors, home theatre systems and sound reinforcement.

With a lower profile and new contemporary design, the ISO Series of stands positions your studio closer to the supporting surface or meter bridge, and the new redesigned isolators moves the acoustic performance another step forward.

IsoAcoustics ISO Series speaker stands are built with a unique, patented isolation technology that provides a high degree of isolations and manages the speaker's energy to deliver authentic, uncoloured sound. This next generation of speaker stands effectively eliminates energy transfer into the supporting surfaces. Bass becomes tighter, overall imaging is enhanced and your speakers are enabled to perform to their full potential. Following the same design philosophy as the ISO-L8R Series, these isolation stands provide 14 variations of height and tilt adjustment to optimize the placement and performance of studio monitors by getting the tweeters in the correct alignment with the listening position.

Whether you're a pro mixing in the studio - a musician creating in a home project environment - or an audiophile who appreciates every nuance of music and sound - you'll hear and appreciate the difference with the ISO Series speaker stands. It's simply the best investment you can make for superior audio.

ISO-155:

Designed for medium size speakers and studio monitors. These stands provide 14 variations of height and tilt to optimize speaker placement and performance. Isolate your studio monitors from the supporting surface and allow them to breathe so they can deliver the clearest and most accurate sound possible.

6.1"x7.5"/15.5x19cm Short: 2.9"/9.5cm Tall: 8.75"/22.5cm 40 lbs/18kg

Notes: A modern classic. Superb little semi-modular monosynth in its own right, but comes alive when paired with other modular gear. A great option for beginners and experienced synth users alike.

Supplier's notes:
The 0-COAST is a single voice patchable synthesizer. Its name reflects the fact that it utilizes techniques from both the Moog and Buchla paradigms (aka "East Coast," and "West Coast," due to their locations), but is loyal to neither and thus implements "no coast synthesis."

While the 0-COAST utilizes classic modular synthesis techniques, it's designed to operate with or without the use of patch cables. The necessary connections have been made from circuit to circuit so it operates as an expressive, musical MonoSynth. Using only the MIDI controller of your choice you could apply new timbres to your existing musical forms!

Using the included Patch Cables you could get more scientific, experimenting with new ways to wire up the circuits. You might even forgo MIDI altogether, disappearing into a cloud of analog FM induced Sidebands and harmonics scattered around a single fundamental drone that has nothing to do with any form of music you've ever known.

Notes: Module A-124 is a special 12dB multimode filter using the "strange" filter circuit of the "EDP Wasp" (an analog synthesizer with black/yellow case built end of the seventies, manufactured by the UK company "Electronic Dream Plant" with Chris Huggett und Adrian Wagner). This design "abuses" digital inverters as analog operational amplifiers leading to distortions and other "dirty" effects that generate the specific sound of this filter. The filter is equipped with a band pass output and a combined low/notch/high pass output. For this output a control knob defines the relation between low and high pass signal. If both signals appear at the same level (i.e. middle position of the Mix knob) one obtains a notch filter. Otherwise the low or high pass signal predominates. The module does not feature self-oscillation in contrast to most of the other filters of the A-100 system.

Inputs: Audio In, CV In (2x)
Outputs: Bandpass Out, Low/Highpass Mix-Out
Controls: Audio and CV attenuator, Frequency, Resonance, LP/HP Mix

The function and operation of this module is very similar to the module SEM VCF A-106-5. But the sound of both filters is very different! The only functional difference is the position of the sockets and controls, and the function of the controls CV2 (A-124: normal attenuator, A-106-5: polarizer).

- 3U Eurorack module, 8HP wide, 45mm deep
- Current draw 30mA

Notes: Adaptor with 2 x phono sockets to 2 x phono sockets

Depth (mm): 10
Height (mm): 30
Width (mm): 25
Product Dimensions (mm): 30x25x10
Net weight (kg): 0.010
Colour: Black

Notes: The lovable oddball of the Arturia range, this brilliant hybrid synth combines versatile wavetable and digital oscillators with analogue filters. Touch keyboard gives uniquely expressive control.

*** New firmware update (26th October 2021) *** Arturia are happy to announce another major new firmware update for MicroFreak, bringing massive new creative functionality for users free of charge.

Firmware V4.0 elevates this hybrid desktop synthesizer's status as a sound design powerhouse even further:
New WaveUser sound engine
Allows for user wavetables(!!)
64-new presets
Sequencer Unison & Chord Voices
Faster Oscillator Encoder Response
....and more!

This update, plus ALL the of previous updates (see Vocoder & Noise Engineering oscillators etc.) cement the MicroFreak as one of the most interesting, powerful and flexible synthesizers on the market, whilst maintaining excellent value for money.

Supplier's Notes:

A synthesizer like no other, MicroFreak is a peculiar, exceptional instrument that rewards the curious musician. It blends wavetable and digital oscillators with analogue filters. It features a unique poly-aftertouch flat keyboard. It adds controlled randomness to sequences. This isn't a revolution, it's a mutiny.

This out-there little music machine features a versatile digital oscillator so you can create rare and interesting sounds with ease. Modes like Texturer, KarplusStrong, Harmonic OSC, and Superwave give adventurous musicians the chance to explore totally new, unheard possibilities. Like having dozens of synths in just one instrument, both wild-eyed newcomers and seasoned professionals will fall in love with MicroFreak's flexible, powerful synth engine.

Physical modelling, wavetable synthesis, virtual analogue, there is nothing as complete and exciting as the MicroFreak oscillator on the market. It's hard to believe from such a small synth, but here it is, ready for you to explore. Excite your creativity and reward your curiosity with a large, diverse sound palette. MicroFreak features 11 awesome oscillators, 4 bespoke Arturia engines, and 7 modes from our friends at Mutable Instruments.

Inspired by the trailblazing 12-dB Oberheim SEM filter, you can make MicroFreak's filter scream or whisper to taste. The filter is state-variable, and can even auto-oscillate! You can use this is any way you like, from taking the edge of the razor-sharp wavetable sounds, or automating the cut-off by modulating it with keyboard pressure or the in-built sequencer.

Record up to four automations, edit notes per step or use the innovative Spice and Dice sequencer functions to find happy accidents. Add randomization to create evolving, original patterns, and virtually rewire and reconfigure its signal chain and controls with the 5x7 modulation matrix.

Notes: Hailing from Japan, Roland has been a giant in the music equipment industry and have lways been the trailblazer since 1972 when they first arrived on the music scene.

After a full decade and a half since the original SP-404, Roland released their SP-404 MK2. The MK2 is an evolution of the classic SP-404 that has been a staple in the music production world. It's not quite an all-new model but definitely not just a refresh.

Decksaver knew with the new portable capabilities of the MK2 with its USB port powered features, or AA battery use, it will be used not just at home, but wherever you go. For this reason, Decksaver have designed and custom-moulded a protective cover right here in the UK.

This super durable polycarbonate shell features extreme durability and offers the highest degree of protection. Not only that, but with the slim form-fit, they fit easily into a gig bag or other ancillary equipment case.

No matter where you are, Decksaver has your SP-404 MK2 covered.

Weight: 0.7kg
Length: 17.8cm
Width: 28.1cm
Height: 3.7cm

Material: Smoked clear polycarbonate.

Notes: HI POWER is Crazy Tube Circuits' next endeavour in pedal + amp-in-a-box overdrives recreating legendary sounds, following the success of Crossfire and Unobtanium.

It was inspired by the sonic combination of two British tone machines. The almighty Colorsound Power Boost meets the blistering high-headroom Hiwatt amp.

While the combination of these two units directly hints at the gear setup of David Gilmour and especially the gear used on Pink Floyd's album: Wish You Were Here (think the guitar solo sounds of "Shine on you Crazy Diamond", "Have A Cigar") the sonic options are endless.

The orange enclosure silicon transistor circuit (Colorsound Power Boost) can deliver from a transparent clean boost to an all-out fuzz driving a tube amp to sonic bliss. Crazy Tube Circuits set out to clone the original unit featuring the true-to-the-original spec BC184 transistors running on 18V DC (via an internal voltage booster circuit).

The ultra-flexible 2-band Baxandall EQ circuit can add bite and low-end rumble to any setup. Crazy Tube Circuits used a reverse log gain pot (labelled as volume), compared to the linear taper pot found in the original units and acted as an on/off switch, to be able to set the amount of boost/overdrive more precisely. While the earlier units didn't feature a master volume control (only as an aftermarket mod - Pete Cornish made an external unit master volume for David Gilmour's Power Boost) Crazy Tube Circuits chose to include one that is setup in a way so that when it is all the way clockwise it is bypassed. Later versions of the Power Boost had 9V power supply and were renamed as the "Overdriver" due to the lower headroom and their ability to drive the signal earlier. They were offered in a grey enclosure and can be seen in the gear setups of Jeff Beck, Marc Bolan, etc. Crazy Tube Circuits chose to incorporate this version as well with a flip of a toggle switch (PWR-ODR toggle switch).

On the left side of the HI POWER you will find an all-analogue circuit set out to emulate the sound and feel of a Hiwatt amp. Following the path of the famed British tube amplifier, this circuit offers authentic amp tone and feel resembling guitar tones from guitar greats like David Gilmour, Pete Townsend, Jimmy Page, Noel Gallagher to name a few. From the big bold high-headroom clean sounds to the face-melting crunchy tones.

True to the last detail, Crazy Tube Circuits have included the full EQ section along with a presence control located at the negative feedback of the power amp simulation circuit. A headroom toggle switch selects between the high headroom 100w power section provided by a quartet of EL34s (think Hiwat DR103), or the lower headroom and compression provided by a 50W power section with a pair of EL34s when hit hard (think DR504). Similar in operation to the original amps the master volume was designed to produce more gain at higher settings.

Crazy Tube Circuits taken the design a step further by adding a switch to select between input channels of the amplifier. You can select between the full response of the normal channel of the amplifier, the increased presence and tight low end of the bright channel input or the "Gilmour-ish" enhanced frequency response and added gain of those inputs linked together. This follows the modifications that Pete Cornish did to all David Gilmour's Hiwatt amps.

Like their other dual overdrive/amp-in-a-box designs, Crazy Tube Circuits also included a passive effects loop to give you the option to connect your beloved pedals between your booster/overdrive and amp in a box or use the two sections as separate and independent effects when using an external bypass switcher/looper. Gilmour enthusiasts will love to insert their Big Muff, Tube Driver and Phase 90 in there. Note that all pedals inserted in the passive effects loop are still in the signal chain when any or both sections of HI POWER are in bypass.

HI POWER features a power-up bypass/engage pre-set function for the footswitches. That way you can select which state your pedal will go to when you plug the power supply. This function comes in especially handy to people that use remote pedal switchers / loopers as they only set the state of the pedal once and then operate from the controller.

All-analog dual booster/overdrive - amp in a box.
Recreates the tones of the legendary setup used by David Gilmour in the recordings of Pink Floyd's Wish You Were Here album.
Right side: Faithful reproduction of the Colorsound Power Boost/Overdriver circuits with true-to-the-original-spec BC184 transistors.
Controls: gain, bass, treble, master, voicing toggle.
Wide gain range control: from transparent boost to gnarly and fuzzy overdrive.
Two-band (treble & bass) Baxandall EQ.
Master knob sets overall output. Huge amount of dB boost available.
Toggle switch to select between the 18V Power Boost style circuit or the 9V Overdriver style circuit.
Left side: Hiwatt AMP in a box overdrive.
All analog simulation of the preamp and power amp sound and response.
Controls: gain, bass, middle, treble, master, input channel toggle switch, headroom toggle switch.
Gain control: from clean to big bold British crunch/overdrive.
3-band Hiwatt style EQ (bass, middle, treble).
Presence control follows the original design/is located at the negative feedback of the power amp simulation circuit to control the amount of upper mid and high frequencies.
Master knob sets overall output volume. Designed to respond like the original control producing more gain at higher settings.
Input channel toggle switch selects between normal, bright, or linked input channels of the AMP for different voicing and gain levels.
Headroom toggle switch selects between the high headroom and dynamic response of a 100W amp or the lower headroom and compression of a 50W power amp.
Independent operation of the BOOST/OVERDRIVE and AMP sections
Click-less true bypass design via high-quality relays for each section.
2 Footswitches / 2 Status LEDs - one for each effect section.
Power-up bypass/engage preset function for the footswitches.
Top-mounted jacks
Passive series effects loop to connect pedals between the two sections or use them separately as independent effects.
Power Supply: Use only 9V DC, 2.1 mm x 5.5 mm, center negative (not included).
Runs internally at 18V DC (via voltage doubler circuit) for higher headroom and tube-like performance.
Current consumption: 84mA.
British Racing Green die-cast enclosure with color-coded lettering for the control section (orange for BOOST/OVERDRIVE section, white for AMP section).
Dimensions: (W x L x H): 119 x 97 x 53 mm.
Weight: 444 g.
Made in Greece.

Notes: A good delay was an essential part of the classic analog synthesizer sound. More often than not, that delay came from a tape-style echo machine until affordable digital delays were created. The Monotron Delay is an analog synthesizer optimized for sound effects. In addition to its analog oscillator, filter and LFO, it also provides a space delay that's indispensible for swooping, cosmic sounds. The monotron Delay even reproduces the pitch changes that occur when you vary the delay time, just as though you were using an analog tape echo. This fat and warm delay will add an authentic edge to your analog sounds.

It also features Korg's class VCF filter for full control over your sounds. The distinctive tone of an analog filter (VCF) can dramatically alter and enrich the sound. The Monotron Delay uses the same highly acclaimed VCF circuit as Korg's classic MS-10 and MS-20 semi modular synthesizers. Originally released over 30 years ago, these instruments are still coveted today for their aggressive, dynamic filters. The VCF Cutoff knob sets the frequency or tone of the filter; the VCF Peak knob adds emphasis. A powerful filter is an essential aspect of any analog synthesizer, applying dramatic tonal changes to the sound, and projecting an intense personality that will stand out in any live performance.

Create classic sounding analogue tape delays to add warms and new dimensions to your synth sounds. Also included is Korg's fantastic enhanced ribbon controller keyboard, while a mini jack input also allows you to run any external audio, such as a Kaossilator, digital piano or guitar, through the Monotron Duo. As standard, the Monotron range comes with a powerful built-in speakers and is battery operated for the ultimate portable experience.

The Low Frequency Oscillator (LFO) waveform used to modulate the pitch now offers a choice of waveshapes, which is a new square wave plus the traditional triangle wave. Both the rate (speed) and the intensity (depth) can be adjusted independently. In addition, a trimpot on the back panel can continuously adjust the shape/direction of the triangle wave or the pulse-width of the square wave to deliver even more versatility. Used in conjunction with the delay, the LFO can create dazzling effects and provide unique possibilities for embellishing your songs.

The Monotron Delay's ribbon controller keyboard features a wide, 4-octave range. This design allows the pitch to be controlled even more aggressively and dynamically, making the Monotron Delay a great weapon for a DJ to get the floor moving with irresistible sound. The reversed white keys and body adornments glows under black light illumination, making the monotron Delay ideal for delivering a striking visual impact in nearly any club environment.

The input jack (AUX input) built into the Monotron Delay's compact body allow you to place any audio source into the Monotron Delay's signal path, directly before the analog filter and delay circuit. This provides a great way to connect a Kaossilator, a guitar, or a digital audio player to the Monotron and enjoy tone-bending filter and delay effect.

A miniature speaker is built into the Monotron Delay. Along with the battery operation and compact size, this feature allows you to enjoy the share the Monotron Delay's analog synthesis sound with your friends, anywhere, at any time. There's also a headphone output that you can use when practicing in private, creating sounds at home, recording, or for connecting to an amplifier or PA system.

Notes: When the classic MS-20 analog synthesizer appeared in 1978, it had a trusted partner in the SQ-10 step sequencer. Now, after thirty years, the MS-20 has been reborn as the MS-20 mini, and the SQ-10 has evolved into the more modern SQ-1.

The SQ-1 is a compact step sequencer with 2 x 8 steps. It's wealth of connection jacks allows it to be connected to the MS-20 and a variety of other synthesizers. Vintage analog synths or the latest compact synths can be controlled from this single unit. You can also switch between a variety of synthesizer modes and use the step buttons to create performances overflowing with spontaneity, just as when using a volca unit.

Liberate yourself from the numerically-bound parameter editing that's typical on a DAW; you'll enjoy truly musical inspiration as you train your ears and concentrate on what your fingertips are doing. Don't miss the experience of music that's driven by your instinct.

Rather than the commonly used V/Oct standard, the CV design of the MS-20 always used the Hz/V standard that provides excellent pitch stability limiting the step sequencers that are able to correctly control the MS-20. As a descendant of the SQ-10, the SQ-1 supports the Hz/V standard, enabling it to perfectly control the MS-20 or MS-20 mini. It goes without saying the V/Oct standard is also supported, and the voltage level of the CV output and polarity of the GATE output can be specified as appropriate for the device you've connected. This versatility will enable you to control a wide variety of other synthesizers as well.

As a connector, the SQ-1 provides two CV/GATE OUT channels, the standard MIDI OUT and USB MIDI, littleBits out (to connect to the littleBits synth kit by littleBits Electronics Inc.), plus the SYNC IN/OUT channel that allows you to connect to the volca series and monotribe. Compact and complete with all the functions you need, the SQ-1 is the ideal hardware sequencer.

The SQ-1 provides two channels (A and B) of 8-step sequencer that can operate consecutively, or be used in a variety of other modes. For example, you can run A and B following each other to function as a 16-step sequencer, ignore the order and make the steps play randomly, or use A and B to control different parameters as they run in parallel. From simple sequences to complex changes, you can choose from a variety of modes to suit your needs.

The 2 x 8 step buttons can be used in the usual way to turn notes on/off, but you can also use the MODE button to switch their function, opening up powerful possibilities such as letting you "perform" the sequence itself, as on a volca unit.

"Active Step" lets you skip steps mid-way through a sequence, and "Step Jump" lets you instantly play just the step that you press, producing irregular rhythms or effects that are reminiscent of short loops. "Slide" produces an effect in which steps are connected smoothly; using this to control a synth bass is an easy way for anyone to generate an acid sound.

Packed with carefully selected functionality, the SQ-1 features a compact and very sturdy sheet-metal body. Placed beside the MS-20 series, you'll notice a sense of solidity that gives the impression they were manufactured in the same era. The unit can operate on two AA batteries or on USB bus power.

Sequence step resolution is selectable as quarter notes, eighth notes, or 16th notes.

You can specify the way in which the step knobs control the pitch. The knob values can specify the pitch directly, or they can specify the closest note in a major, minor, or chromatic scale.

Notes: Akai's mid-range MPC features full-size pads plus a built-in rechargeable battery and speakers. Integrated phono stage makes it easy to sample from vinyl. A hugely capable studio centrepiece.

*** Introducing MPC Stems- March 2024 ***

Akai Professional now introduces the next chapter of sampling innovation and production powered by the groundbreaking MPC Stems bringing sampling into a new chapter.

With MPC Stems, you can access the raw building blocks of any sample or vinyl record, isolating the DNA of any record. Producers can now manipulate the Drums, Bass, Music, and Vocals, opening new creative possibilities.

Akai Professional introduces the ultimate creative workflow with Stems Separation seamlessly integrated into the leading MPC series, powered by MPC 2 Desktop Software.

With MPC Stems, producers and beat-makers can now unlock unmatched sampling creativity by easily isolating drums, bass, music, and vocals from any audio, vinyl recording, or sample revolutionizing the art of sampling.
Experience lightning-fast workflow with superior sound quality, keeping you inspired throughout the creative process.

Slice and isolate samples while maintaining chop regions across each of the four stem layers.

Take complete control with direct manipulation of stem layers from the pads, adjusting volume, pitch, pan, start, and end points with instant responsiveness.

MPC Stems requires MPC 2 Desktop Software running 2.14 or higher, compatible with MPC Live, MPC Live 2, MPC One, MPC One +, MPC X, MPC XSE, MPC Key 37, MPC Key 61, MPC Studio Mk 2 in Controller Mode.

Supplier's Notes:
Meet MPC Live II, the full MPC experience in its most portable configuration yet. Everything you need to make music, anywhere, right at your fingertips.

There's no need to compromise for portability. MPC Live II is the complete MPC experience without missing a step. A rechargeable lithium-ion battery means you can work anywhere for hours. Full-size MPC pads give you the ultimate in drum performance and the expanded function buttons allow for quick editing on-the-fly so you never miss a beat.

For the first time ever, you now have studio-grade monitors built-in directly to your MPC. No need to waste precious time looking for your headphones, untangling cables or powering up external monitors. These full range stereo monitors deliver low end thump along with tight top end to make portable beat-making the sonic experience you need to feel your music.

MPC Live II integrates into your creative space with all the ports, jacks and connectivity you need. USB 3.0, 2x2 MIDI, CV/Gate, 3 stereo outs and more. WiFi and Bluetooth connectivity make for a completely wireless workflow. No matter the device, MPC Live II is ready to get connected!

MPC Live II will super charge your production. With MIDI performance to tap in to as many devices as you need, an intuitive and streamlined layout not to mention the MPC workflow features you need; 16 Levels, Note Repeat, Auto Sample, Chords & Notes More and so much more. Get ready to level up to the MPC Live II.

KEY SPECS:

Pads:
(16) velocity and pressure-sensitive pads, RGB-backlit
(8) banks accessible via Pad Bank buttons

Knobs:
(4) 360- touch-sensitive Q-Link Knobs
(4) Q-Link Knob columns accessible via Q-Link button
(1) 360- encoder for display navigation and selection via push

Buttons:
(27) dedicated function buttons; red, amber, or green backlit

Display:
6.9" / 176 mm (diagonal)
5.9" x 3.7" / 150 x 93 mm (width x height)
Full-color LED-backlit display with touch interface

CPU: Quad-core ARMr processor
RAM: 2 GB
Storage: 16 GB, expandable via SATA connections

Connections
(2) 1/4" (6.35 mm) TRS inputs (1 stereo pair)
(6) 1/4" (6.35 mm) TRS outputs (3 stereo pairs)
(1) 1/4" (6.35 mm) stereo headphone output
(2) RCA inputs (1 stereo pair)
(2) 5-pin MIDI inputs
(2) 5-pin MIDI outputs
(4) TRS CV/Gate jacks, 8 outputs total
(1) Ethernet link port
(2) USB Type-A ports
(1) USB Type-B port
(1) SD Card slot
(1) Power Adapter input

Power:
Via power adapter: 19 V, 3.42 A, center-positive, included
Via battery: Up to 5 hours of battery life

Dimensions (width x depth x height):
16.2" x 9.6" x 1.8"
411.5 x 243.8 x 45.7 mm

Weight:7.45 lbs/3.38 kg

Notes: - High-grade patch cable designed for modular units
- 3.5mm mono jack plugs
- Length: 50cm
- Angled connector on one end
- Orange finish

Notes: Break out MIDI signals into a 3.5mm stereo jack.

- Tip = Pin 4 (Source)
- Ring = Pin 5 (Sink)
- Sleeve = Pin 2 (Shield)

Notes: Pack of high Quality patch cables. Not too stiff, not too loose!

One colour for each size make Befaco patch cables just perfect to keep them organized!

This pack contains 5 high quality orange patch cables.

Notes: Best value Buchla module ever? An official Buchla module produced by TipTop Audio, the 258t is a dual triangle-core oscillator, with sine/sawtooth wave shapes in the top half and sine/square at the bottom. Bags of character.

Supplier's Notes:
Two independent voltage-controlled oscillators. Each has one processing input, a frequency modulation input and a 1V/oct input.

Waveshapes, as well as frequency, can be voltage controlled. Model 258 oscillators feature low sine wave harmonic content, negligible settling error, and high short and long-term stability, even with rapidly changing ambient temperatures.

Trimmers:

There are three trimmers for each oscillator on the back of the module:

1V/oct is the octave tracking trimmer and is set at the factory using high precision instruments.
SHAPE is the trimmer that set the sine wave, for the lower harmonic content of the sine wave.
VC WAVE SHAPE sets the response of the waveshaper to the incoming control voltage. Both SHAPE and VC WAVE SHAPE trimmers are used to adjust the sine wave purity.

Size: 18HP
Depth: 45mm
Power: +12V 70mA / -12V 40mA

Notes: Plastic dust cover for Soma Laboratory Terra.

*** The Terra is not included, it is shown in the pictures for demonstration purposes only. ***

Notes: Eurorack version of 1010's superb Bluebox. Vast power in 30 HP, with the ability to mix, record and play back in mono and stereo, hook up to a computer over USB for stereo I/O and run effects, all with CV control.

Supplier's Notes:
The bluebox Eurorack edition is the new Eurorack mixer with effects and multichannel recording/playback based on the award-winning bluebox desktop mixer. With the Eurorack edition's USB-C EXT port, you can send 2 channels of audio to and from your computer. Plus, you can control up to 6 mix settings with the 6 CV inputs. Whether recording your Eurorack jams, using it to play stems as backing tracks, or a combination of both - bluebox Eurorack edition will rock your rack!

Connect your eurorack, sampler, drum machine, and synthesizer outputs to 12 mono, 3.5 mm inputs and map them to 12 mono tracks or 6 stereo tracks - all with independent control for recording and playback. Connect your computer to the USB C port to send and receive two channels of audio.

The bluebox Eurorack edition is the ultimate in compact mixing, effects, recording, and playback for Eurorack. Smack it in your rack and hit the road with a self-contained, electronic music powerhouse!

When you purchase a bluebox Eurorack edition, you will receive:

a bluebox Eurorack edition 30 HP Eurorack module
A microSD card with bluebox firmware and pre-loaded project files
two Eurorack power cables
a bluebox Eurorack edition Quick Start guide
two MIDI Adapters

Technical Specs

Dimensions & Power
30 HP
Module dimensions including knobs: 6" x 5"x 1.6"
Depth behind front panel with ribbon cable: 1.0"
Requires the +5V rail which may not be present
on some older racks.
Uses 500-850mA at +5V (depending
on screen brightness), 320 mA at +12V, and 82mA at -12V
Requires two power connections
Capabilities
12 mono tracks, 6 stereo tracks or something in between
Connect to TRS or USB C MIDI for beat syncing effects
Lots of headroom with support for Eurorack levels up to +/-5V inputs and outputs
3 effects: reverb, delay and compressor
Records and plays back 48k, 24-bit audio WAV files
4 band EQ per track
Durable aluminum faceplate
Stream 2 channels of audio in and out over USB C

Inputs and Outputs
12 mono 3.5 mm TS inputs
2 independently controlled 3.5 mm TS output pairs that can be used as 4 mono outputs
1 stereo 3.5 mm headphone output
6 CV Inputs
1 USB C MIDI Device port
1 TRS MIDI Input
1 TRS MIDI Output
1 USB C Ext jack for streaming audio
3.5" touch screen, 4 knobs, 8 navigation buttons and 3 transport buttons

Notes: - High-grade patch cable designed for modular units
- 3.5mm mono jack plugs
- Length: 15cm
- Yellow finish

Notes: The tools we use to compose and produce music are dear to our hearts. Dust, liquid and accidental impact have taken many a good FX unit down over the years - this is where Decksaver steps in. Precision trimmed for perfect fit whilst accommodating cables, your Bim/Bam/Boum can sit ready for operation. Slides straight into a flight or soft case for maximum protection during transportation. Shields delicate controls and internal components from damage.

Notes: 1U version of Happy Nerding's effects module, offering a total of 32 effects, with user-storable presets and CV control. Great value in a convenient package.

Supplier's Notes:
32 unique audio effects arranged in 4 banks of 8 effects. Three effect controls plus analogue Dry/Wet control with dedicated CV input. High quality stereo signal pass. Assignable CV input to effect controls or to Sample Rate reducer (changes internal clock). Four user storable presets - stores selected program and all three controls. Spin FV-1 based.

The last used effect, assigns and presets are always remembered.

32 effects are simultaneously available, but FX AID can be reflashed with other effects in any order.

Reflashing procedure is quite easy: playing 40 sec long .wav file of line level amplitude to CV input.

Reflashing mode: hold both buttons for 10 sec.

By default it runs on 32.77 kHz and, if sample rate reduction assign is used, this sample rate can be decreased down to 2000 Hz or brought up to 48 kHz.

Dimensions

24 HP
40 mm deep
Module is a 1U tile in Intellijel format

Current Draw

80 mA +12V
30 mA -12V

Notes: Successor to the excellent Metropolis, the Metropolix is a performance-focussed step sequencer with some really neat features, including modulation and sub-sequences in Loopy mode.

Supplier's Notes:
The Intellijel Metropolix is a unique and powerful Eurorack format musical sequencer. With an abundance of hands-on, tactile controls and a wealth of modulation possibilities (both internal and external) you can quickly and easily create infectiously musical sequences that are never boring. Even the simplest riff can be brought to life with seemingly endless options to create variations or real-time manipulations. Equally at home in the studio or a live improvised performance, the Metropolix is sure to become a staple source of fresh ideas and killer riffs in your creative process.

Width: 34HP
Depth: 25mm
Power: 95mA @ +12V 10mA @ -12V

On first blush, it appears to be a simple 8-stage sequencer - but there is far more functionality than first meets the eye:

There are two tracks (TRK 1 and TRK 2) that are variants of the single master pitch/gate sequencer, which is programmed via the PITCH sliders, PULSE COUNT and GATE TYPE switches. Each track interprets the master sequence in a variety of ways - creating complementary sequence variations that enable you to generate counterpoint, polyrhythms, and all manner of sonic movement (both subtle and extreme). Each of these tracks has its own playback ORDER, sequence LENgth, clock DIVision, SWING amount, SLIDE time, and track GATE lengths. Other track-based sequence variables are accessible from the TRACK MENU, and include Pitch Slider inversion; sequence note range; track transposition; and more. In addition, Tracks 1 & 2 both have multiple lanes of per-stage playback parameters, including: GATE override; PITCH override; RATCHet count; PROBability of playback; ACCUMulating transposition, and a dedicated CV lane. Each stage also has a SKIP feature, and a pitch SLIDE option.

8 separate and individual MODulation lanes are accessed via the MOD button. Each MOD lane has 8-stages of modulation values and its own playback ORDER, LENgth, and clock DIVision; and each lane is routable to one of Metropolix' two assignable outputs or to dozens of internal destinations, allowing for some sophisticated and powerful self-modulation.

A trio of AUX inputs allows for external modulation of user-assignable sequencer parameters for even greater variation, while two assignable CTRL knobs give you direct access to the parameters you want to adjust most frequently during a performance. With dedicated Pitch/Gate outputs for both Track 1 and Track 2; two totally user-assignable outputs (A and B); and internal MOD routing, Metropolix features a wealth of patching opportunities.

Metropolix also features a Loopy mode, allowing you to instantly play back short sub-sequences, or even "play" the stage buttons directly (like a 'keyboard').

Metropolix stores up to 64 preset configurations (in 8 banks of 8 presets), and all live settings are stored in EPROM, ensuring that your Metropolix will always power up exactly as you left it - even if you haven't saved them to a preset. By default presets can change all the structural (menu-based) elements of your sequencer without overwriting the front panel controls, but full recall is also available.

The operation of the Metropolix is optimized for live performance and jamming, with quick access to all the most important performance parameters, and the ability to greatly affect your sequences with a single slider or switch.

Notes: - 6.3 mm jack male mono to 3.5 mm jack male mono
- Length: 1.5 metres

Notes: Module A-160-2 is an enhanced version of the standard clock divider A-160. The module is a frequency divider for clock/trigger/gate signals, designed to be a source of lower frequencies, particularly for rhythm uses. The Clock input will take any digital signal from, eg. LFO, MIDI sync, or the gate from a MIDI-CV interface. At the outputs, you have access to three sets of seven different sub-divided clock signals, from half the clock frequency down to 1/128. The low/high levels of the output signals are 0V and about +10V.

The A-160-2 also has a reset input. Whenever a reset signal is sensed, all outputs are set to certain levels which depend upon the selected mode.

These are the most important features of the module:

Three different sets of dividing factors, selected by a three-position switch at the front panel:
- Power of two: 2, 4, 8, 16, 32, 64, 128
- Prime numbers: 2, 3, 5, 7, 11, 13, 17
- Integer: 2, 3, 4, 5, 6, 7, 8

Two output modes, selected by a two-position switch at the front panel:
- Gate mode: outputs act like the outputs of typical binary dividers
- Trigger mode: in this mode the outputs are AND-wired with the clock signal (i.e. the clock pulsewidth affects the pulsewidth of the outputs)
- Clock edge type selected by a jumper on the pc board:
- Positive: the rising edge of the clock signal triggers the state change of the outputs
- Negative: the falling edge of the clock signal triggers the state change of the outputs

Reset behaviour by two jumpers on the pc board:
- Level triggered: the level at the Reset input triggers the Reset
- Edge triggered: the edge of the signal at the Reset input triggers the Reset
- Positive: a high level (> 2.5V) or the rising edge at the Reset input triggers the Reset
- Negative: a low level (< 1 V) or the falling edge at the Reset input triggers the Reset

Output polarity selected by a jumper on the pc board:
- Positive: non-inverted outputs
- Negative: all seven outputs are inverted

Width: 4HP / 20mm
Depth: 35mm (Measured from the rear side of the front panel)
Current: +12V: +50mA, -12V: -0mA

Notes: The little brother to the original DrumBrute arguably packs a bigger punch. Gritty analogue sounds are on offer, but the sequencer is just as inspiring. A great alternative to the usual Roland suspects.

Supplier notes:
This is the drum machine you've been waiting for.

Combining bold, hard-hitting analogue sounds, a monstrous output distortion, performable controls, superb connectivity, and a powerful sequencer, DrumBrute Impact will fill your music with energy and muscle.

Putting the focus on "Brute", DrumBrute Impact features 10 high-energy, refined, punchy analogue sounds.

You can also use the exclusive "Colour" sound-shapers to introduce unique, per instrument effect for some variation. Boost the harmonic content, add some drive, snap, or crack at the touch of a button, you can even automate tonal changes by creating a "Colour" sequence. If you want your drums to push even harder, use the built-in distortion on the output for some drum-optimized crunch.

DrumBrute Impact is a drum machine for musicians and producers who crave raw power and monstrous tone.

Awesome drums made easy:

Sharing the same prize-fighting sequencing architecture found in the original DrumBrute, you'll love the simple, fun, and intuitive sequencer in DrumBrute Impact.

Whether you want to create complex, phasing polyrhythms or straight, pounding rhythms; record a finger-drumming performance; punch in a step-sequenced masterpiece; DrumBrute Impact beats to your rhythm. Use the touch strip to create some real-time glitchy, beat-repeat breakdowns, spice up a single instrument or your whole pattern with a dedicated 'Random' knob, and add some syncopation and groove with the 'Swing' feature.

A true analogue experience:

Connect to your other gear, sync up, and make some music the old-school way.

Get away from computer screens, say goodbye to sub-menus, and jump into the world of tactile, instant, analogue satisfaction. Featuring a huge array of sync and connectivity options, you'll be able to hook up and jam with practically any other synth, sequencer, or MIDI-enabled instrument. Mix on the fly with dedicated controls for every function, multitrack, record, effect, and mix the sound your way with multiple bus outputs. Save patterns that you love, chain them together, and create full songs and live sets, all without looking at a single screen.

DrumBrute Impact is a massive sounding, creativity fuelling beast, with effortless workflow and amazing performance controls.

Notes: High quality audio leads for exceptional sound quality and reliability. High grade twin cable comprises an insulated pure copper core and global shielding. The durable PVC sheath has a soft texture to avoid knotting. Terminated at one end with a pair of RCA phono plugs and at the other end with 2 x 6.3mm mono jack plugs.

Notes: Part of 1010's excellent Nanobox series, the Tangerine is a tiny powerhouse sampler. A fresh new approach to sampling, from one-shots to loops, all the way through to four-hour recordings.

Supplier's Notes:
Sweet and Tangy Sampling

The nanobox | tangerine delivers powerful sampling in an ultra portable form factor. With this nanobox, you can add recording, sample playback, clip launching, slicing, and musically intelligent looping capabilities to your desktop or travel rig. With an intuitive touch screen interface, nanobox | tangerine makes easy work of selecting, editing, and tweaking your samples. You can stream large samples of up to 4 GB file size straight from the microSD card. Interact with other musical components via MIDI. Load multi-sample banks with over 500 samples for amazing instrument reproduction. Tweak your configurations to get them just right, then save them to multiple presets for future reuse.

Top features

Play up to 24 stereo polyphonic notes when your samples fit in the 64 MB of internal memory or up to 8 larger stereo samples streaming directly from the microSD card

Play multi-sample banks with up to 16 velocity layers and 576 WAV files loaded in one preset

Configure 8 stereo sample pads per preset as single or multi-samples, clips, slicers, or new recordings

Stream long samples from the microSD card with a max sample size of 4 GB, which can be many hours of audio

Trigger samples with the touch screen or MIDI input as one shots or melodic notes

Control how samples start and stop by choosing from one-shot, toggle, gate and piano (New!) launch modes

Tweak playback through a variety of sample parameters, including start position, length, pitch, gain, filter, loop mode, launch quantization, ADSR, Exclusive Grouping, clip synchronization, slice placement and sequencing, and MIDI note and channel mapping

Quickly and easily use MIDI mapped controls for more tactile access to common parameters

Record up to 16 sequence layers per preset.

Get into the groove with a fast, fluid, and intuitive workflow

Make music anywhere thanks to a compact and nearly indestructible design

Recording Capabilities

Configure each pad for stereo or mono recording with the option to synchronize the start and stop times to clock inputs
Trigger recording via audio level threshold
Create perfectly sized loops by setting the recording length
Enable immediate playback after recording for live looping capabilities
Make recordings up to 4 hours in length
Resample the master output without patching
Automate recording of a multi-sample bank via MIDI
Store recorded samples as WAV files on the micro SD card then remove the card to transfer them to your computer

What is Included:
nanobox | tangerine - Compact Streaming Sampler
MicroSD card with 85 presets and over 1500 wav files
Colour matched USB power cord
Type B TRS MIDI To MIDI 5 Pin DIN adapter
Quick Start Guide

Technical Specs:

Power: USB-C connection 5V, 500mA
3.5mm audio input and output
Maximum input and output level: 2Vrms
DAC and ADC resolution: 24-bit
Internal resolution: 32-bit
Sample rate: 48kHz
MIDI Input: 3.5mm Type A/B auto sensing
MIDI Output: 3.5mm Type B
Clock Input: 1,2, 4, 8, 12 or 24 PPQ selectable
MIDI support: Note On/Off, Velocity, Pressure, Mod Wheel, Aftertouch, CC mappings to common parameters, program changes and clock
H x W x D: 1.5" x 3.75" x 3"
Weight: 0.25 lbs.
2" touch screen, 2 knobs and 4 buttons in a 3.75" x 3" x 1.5" package

Additional information

Weight: 0.65 lbs
Dimensions: 7.75 × 4.85 × 2.25 in

Notes: The Dual Stereo Gate (DXG) music synthesizer module is a Dual Stereo Low Pass Gate and Mixer. It follows in the footsteps of the QMMG, Optomix, RxMx, DynaMix, and LxD. Unlike its predecessors, the DXG is specifically oriented around mixing stereo signals, making it an important addition to any system containing modules like XPO, QPAS, Morphagene, Mimeophon, and other stereo modules by Make Noise or others.

Unique to the DXG is a new low pass gate circuit that does not use vactrols. This circuit is 100% analogue and its response was arrived at after many months tailoring it to meet or exceed the expectations that have been set by all the vactrol low pass gates that Make Noise has created over the years.

In the past, Make Noise produced the Dynamix module and Dynamics circuit in the 0-COAST, both of which are vactrolless LPGs; however, the DXG is a completely new approach which better implements the gentle single pole filtering of a low pass gate, while also emulating the slow decay and memory of the vactrol based low pass gate. This new circuit makes possible the consistency of response necessary for versatile stereo use, while also keeping the module small and affordable so that it can be a key part of just about any modular system.

As on all of Make Noise's low pass gates, the DXG's Control parameter is used to set both the amplitude and the frequency content of the sound that passes through it. The control parameter tends to open faster than it closes, imparting a subtle decay phase onto any envelope shape that is used to modulate it.

Unlike previous low pass gates made by Make Noise, all the DXG's inputs and outputs are stereo. Each set of inputs is normalled so that the left input can be used for a mono signal, sending a copy to both left and right outputs. The Auxiliary inputs are also a stereo pair with mono normalization. These normalizations allow for the DXG to be used as a simple three channel stereo mixer, with one or two of the channels additionally being used for dynamics control and note event generation. The Aux inputs can be used to chain together larger decentralized mixes using additional DXG modules, or X-PAN, Optomix, modDemix etc.

Features

- Make Noise's first Stereo Low Pass Gate

- Vactrol-free design for classic Low Pass Gate sounds, but with the balance and consistency needed for true Stereo

- Fully Stereo i/o for easy integration into a Stereo-equipped modular synthesizer

- All Left inputs normalled for easy use with Mono signals

- STRIKE Input allows use of Gate signal to trigger Low Pass Gate circuit, creating "plucking" or "pinging" sound from any Gate

- Summing stage with Stereo AUXiliary IN allows for chaining of multiple units, creating larger mixes

- Part of a decentralized mix console integrated throughout the system along with X-PAN, Optomix, XOH, etc.

- Pairs well with XPO, QPAS, Morphagene, Mimeophon, Spectraphon etc.

Width: 8hp
Power:
74mA @ +12V
86mA @ -12V
Module Depth (incl power cable): 43mm

Notes: Save space in your rack with stackable cables.

These are the newer shorter stackable Eurorack Patch Cables. Patching is more stable and makes it easier to get a lid on that performance case.

One end of the cable has a male and female jack, the other end as just a male connector. They come in sets of 5 cables.

Available in 6in (15cm), 12in (30cm), 18in (45cm), and 24in (60cm).

Notes: Right angle 2.1mm barrel plug (5.5mm outer diameter, positive tip). Short barrel to barrel cable for daisy-chaining Row Powers and/or Pods. Cable is 11" long (centre of tip to centre of tip), suitable for two Pods next to each other or in front/behind each other. Also compatible with Row Power modules.

Both ends of the cable have a right-angle plug.

Notes: Keyboard meets sequencing in Arturia's all-round controller. USB, MIDI, CV and analogue clock compatibility make this 64-step polyphonic sequencer a true all-rounder. Great value.

Supplier's Notes:
KeyStep 37 goes beyond an easy-to-use 64-step sequencer, arpeggiator and MIDI keyboard. It's responsive, dynamic, expanded in every direction to encourage musical exploration - the controller that's built to help write music and also includes Ableton Live Lite, making it a complete music production starter kit, as well as appealing to veteran musicians. Like KeyStep and KeyStep Pro before it, KeyStep 37 offers unique features not found in any other product.

The familiar KeyStep formula, expanded. KeyStep 37 features a velocity-sensitive 37-note keybed, complete with aftertouch and RGB LED feedback, while remaining lightweight and compact.

At the center of the control panel, you'll find 4 new knobs with an LED screen, giving you instant access to inspiring new expressive tools and MIDI tweaking - total creative control.

The new controls unlock KeyStep 37's unique & enhanced Chord mode. Choose from 12 chord types, an array of strum effects, and spread the voices out into complex velocity-sensitive parts that respond like a stringed instrument.

Map out KeyStep 37's 3-octave keyboard range with a scale of your choice using Scale mode. Any key you play will automatically quantize to the nearest note in the chosen scale.

Tap into the inner workings of your MIDI hardware and software with assignable 16 MIDI CC pa-rameters across 4 switchable banks. Use the 4 new controls to tweak settings on the fly for dy-namic performances.

The core of your setup:

KeyStep 37 is designed to be put in control. An accessible interface, a compact design and com-prehensive connectivity make it the perfect centerpiece for your rig - whatever your needs.

Hook up your synth hardware with MIDI in/out. Control your favorite VST instruments with MIDI over USB. Use CV pitch, gate and mod connections for modular integration. Analog sync in/out keeps everything in time without hassle. The best bit? Use it all at the same time.

Included is a free copy of Ableton Live Lite, an accessible music-making suite for your Mac or PC. Register KeyStep 37 for your free download and get creative right out the box - let the music flow freely.

Notes: Pack of three, six-way, Befaco-branded multiples with six 3.5mm inputs.

Notes: Highly sought-after utility tool that always sells out quickly. Full colour display gives visualisation as an oscilloscope, spectral analyser, spectograph, tuner and more. Waveform and clock generator options too.

Supplier's Notes:
The Ultimate Eurorack Utility Module (and a whole lot more!)

The DATA is a digital platform for testing, measurement, and signal generation in Eurorack modular synthesis systems. It is a modular tool kit, with functions applicable to any system and style.

Use the DATA's scope to view the interactions between your control voltages and audio signals, allowing you to master your modules by understanding their voltage ranges, control shapes, and parameter responses. Use the DATA's dual waveform generator to dial in a precisely scaled LFO for CV control, or use the waveform's frequency "note mode" to effortlessly make dyads (two note chords). Use the DATA's clock program as a master clock or to divide or multiply an incoming clock signal, sending four different clock outs to gate modules directly or as control to sequencers.

The possibilities of the DATA are basically unlimited; with the included microSD you can update the DATA's firmware and we can continue to refine and create new programs.

Notes: Eight channels of audio and CV sampling with real-time editing and processing. Does basic sampling well but quickly gets creative and weird.

Supplier's notes:
The 'Squid Salmpler' is a Eurorack 8 channel audio & CV sampler. It is designed for immediate real time sampling, editing and mangling within a modular context.

Taking influence from early hardware samplers, The Squid Salmple focuses on usability and instinctive operation, incorporating a proven Pamela's Workout style user interface for minimal screen dependence and a fun, hands on experience.

With support for sampling and playback for both audio and CV, as well as CV control of all parameters, on-the-fly bank loading and saving to USB, The Squid Salmple brings a unique take on old school sampling into the modular realm.

The Squid Salmple comes with a USB Stick containing approximately 90 banks of original carefully curated royalty free samples. This includes a wide range of sounds from classic drum machines and weird synths to field recordings and CV modulations. Banks are provided by both ALM and some of our favourite artists and friends including Mumdance, Solid Blake, Russell Haswell, Lauren Flax, Dave Burraston (NYZ), Sue Zuki, Dungeon Acid, Sasha Lewis and Andrew Duff.

Notes: Module A-151 (Quad Sequential Switch) is like an electronic four-position rotary switch.

It includes trigger and reset inputs, four in / outputs, and a common out / input. Each time a pulse is received at the trigger input socket, the common out / input is connected to the next in / output. After the fourth in / output, the next trigger makes it step back to the first again, and so on. A positive pulse at the reset input switches the out / input immediately back to the first in / output (see Fig. 1). Voltages in the range -8V...+8V at the O/I resp. I/O sockets can be processed by the module.

Four LEDs indicate the active in / output (i.e. the on that is connected to the out / input at any particular time).

Notes: Excellent value from Arturia's hugely popular mini controller. 25-key design with pads, faders, rotary pots and transport controls for full hands-on playability of software synths and DAW features.

Supplier notes:
MiniLAB 3 is a compact MIDI keyboard & pad controller that lets users make music, right out the box. With a creative plug-and-play workflow, versatile assignable controls, 500 curated sounds from Analog Lab's massive library, and a bundle of world-class creative software, MiniLAB 3 is designed to finally help beginners and professionals to get truly immersed in their music creation flow, whatever their style.

Hands-on, easy to use

From the great-feeling keyboard to the smart DAW-integrated pads & faders, to the real-time mini display, every aspect of MiniLAB 3 is designed to be intuitive, expressive, and a joy to use - for beginners and pros alike.

Creative features

Enjoy a workflow that aids the creative process, with features like a built-in arpeggiator, Chord mode, custom DAW presets, and easy transposition. Making music has never been so accessible.

Portable, compatible design

MiniLAB 3 is built to fit seamlessly into any setup, from bedroom to stage, with its compact & lightweight design, deeper DAW integration, and MIDI out & USB-C connectivity.

Eco-Designed

MiniLAB 3 is built with longevity and sustainability in mind. A rugged road-ready design, 5-year warranty, minimum 50% recycled plastic construction, and 100% recycled packaging means this controller goes the distance.

Creative software included

On top of a world-class MIDI controller, users get a full package of premium music-making software, from an industry-standard DAW to well over 500 synth & keyboard presets.

Production-ready bundle

Everything that users need to start creating their own music. Explore premium tools like Ableton Live Lite, Analog Lab Intro, UVI Model D grand piano, and Native Instruments "The Gentleman upright piano; enjoy access to millions of royalty-free lifetime loops & samples with a Loopcloud 2 months subscription + 1 Welcome pack + 1 pack of your choice; get to grips with playing keyboard, finger drumming, DAW production, and even music theory with a Melodics "unlimited" trial subscription & bonus lessons.

What's fun to play with

MIDI Control Center

Use the Midi Control Center to customize your MiniLAB. You can change the Velocity curves (keyboard and pads), the Knobs acceleration, the Pedal input type and polarity, the Message types with their Min and Max values, the MIDI Channels, and much more. Shape the MiniLAB exactly the way you need it to be.

Switch MIDI Channel - Shift + a key with a number above it will change the MIDI Channel.

Hold a note - When engaged, every note played will be held. Playing new notes will replace the previously held notes.

Chord mode- Shift + Hold will activate "Chord mode". Then, just play one note and it will play the full chord with the pressed note as the root note. You can record a custom chord by keeping Shift + Hold pressed while entering up to 16 notes.

Transposition - Transpose the whole keyboard by octaves or semitones by pressing Oct or Shift + Oct.

Transport Control - While pressing Shift, you can use the corresponding pads to Play, Stop, Record, Loop, and tap the tempo.

Arpeggiator mode - Shift + Pad#1 engages/disengages the Arp. Long press Shift + Pad#1 to enter the Arp settings. Then use the 8 knobs or the main encoder to set the Arp as you please.

Hold + Chord + Arp - Can be activated at the same time, allowing you to keep the Arp running while tweaking the parameters of a preset.

Pad banks - Shift + Pad#2 toggles between Bank A and B).

Programs - Shift + Pad#3 cycle through the programs. Arturia and DAW programs will automatically connect to any Arturia Software or DAW if there is one open on the computer. You can create and add some User Programs to customize the MIDI CCs, notes, pad colours etc.

Arturia Program - use the main encoder to browse through presets. Press the Main encoder to select a Preset. Long Press the main encoder to like/unlike the Preset. Shift + Main encoder will browse through Types. Select one, and then browse through the filtered presets.

DAW Program - use the main encoder (turn or click), and "Shift + the main encoder" (Shift + Turn and Shift + Click) to access different features depending on the connected DAW.

Back Panel connectivity
USB-C = Connect to a computer or a power source
Control Input = you can set the pedal input to be Sustain, Expression or Footswitch.
MIDI Out = Send midi through MIDI Din port

Notes: Updated version of Erica's superb EMS-inspired synth, featuring a powerful dual oscillator synth architecture, piano roll sequencer, modulation matrix and recordable joystick.

Supplier's Notes:
Based on lessons learned from the SYNTRX, Erica Synths decided to create an instrument that would integrate even deeper into contemporary electronic and experimental music setups and cover sonic territory from daunting drones to powerful basslines and glitched noisescapes - the SYNTRX II is a new dark horse for experimental sonic rides.

The SYNTRX II is the culmination of Erica Synths' analogue sound design circuits - two perfectly stable main oscillators with waveshapers, a modulation oscillator with 1V/oct tracking, a versatile multimode filter, supercharged external instrument inputs with an envelope follower, a unique, great-sounding ring modulator, a recordable joystick, built-in piano roll sequencer and stepped modulation sources, all arranged around Erica Synths' signature matrix mixer and topped off with powerful FX on their new DSP platform.

"The SYNTRX 2 is awesome, a very different instrument from V1. My first synths were the VCS3 and the AKS and are still among my favorites today. The Syntrx 2 is pushing the boundaries of possibilities & experimentations much beyond the original analogue version. The Syntrx 2 is an instant classic". - Jean Michel Jarre

Features

Two perfectly stable main oscillators with CV-controlled waveforms
Modulation oscillator with variable waveforms
Highpass and Lowpass filters in series
Free running or gate synced sample and hold circuit
Multi-colour noise generator
DC coupled instrument inputs with signal inversion and envelope follower
Ring modulator of unique design
Looping trapezoid envelope generator and VCA
Two output VCAs
Signal meter with a dedicated audio/CV output
FX section with great sounding Delay and Reverb developed in collaboration with 112db.com
Recordable Joystick
Analogue patch matrix with 3 attenuation levels in each patch point
254 patch memory
Piano roll sequencer and two stepper modulation sources
DIN5 MIDI Input and MIDI Thru
Two assignable outputs
Headphone output
Dimensions: 309mm x 457mm x 115mm (with the joystick in centre position)
Weight: 3.9 kg

Notes: Compact and user-friendly all-in-one production studio from Rode's excellent RodeCaster series. Aimed at podcasters and content creators, the RodeCaster Duo makes it easy to achieve great results.

Supplier's Notes:
The RODECaster Duo is the ultimate compact audio solution for podcasters and content creators. Combining revolutionary features with superior sound quality, endless customisability and unmatched ease of use, the RODECaster Duo is all you will ever need to record incredible audio for your content.

Everything You Need to Sound Spectacular

The RODECaster Duo is the world's most powerful all-in-one audio production solution. Condensing a complete professional broadcast studio into a compact and intuitive console, it gives you everything you need to sound spectacular, whether you're podcasting, streaming or creating any kind of content. Loaded with cutting-edge next-gen features and supercharged by a high-performance quad-core audio engine, this is all you need to produce exceptional content.
Incredible Audio, Incredibly Easy

The RODECaster Duo is incredibly simple to navigate with its large high-definition touchscreen, tactile rotary encoder and broadcast-quality faders giving you hands-on control over every aspect of your sound. Get your project set up in seconds, and with professionally tailored presets and our intuitive VoxLab™ processing editor, you can dial in your perfect sound with the tap of button or twist of a knob. It's never been easier to create amazing content.
Revolutionary Sound

The RODECaster Duo features world-class Revolution Preamps that deliver pristine audio quality with any microphone, instrument, headset or line-level source. Designed from the ground up specifically for the RODECaster series, these ultra-low-noise, high-gain preamps will give you plenty of output while remaining incredibly quiet, eliminating the need for microphone boosters, lifters or external processing

Professional Processing, Powered by APHEX

Craft your sound with studio-quality audio processing powered by one of the most revered names in pro audio: APHEX. On-board is a suite of authentic emulations of legendary hardware audio processors, including the Aural Exciter, Big Bottom and Compellor master compressor/leveller. There is also a studio-quality compressor, noise gate, high-pass filter, de-esser and three-band equaliser for each channel. Sound exceptional every time you hit record.

Super Compact, Highly Portable

The RODECaster Duo is incredibly versatile and powerful, but it's also exceptionally compact and portable. Take your podcast on the road, create content from home or the office or simply liberate some desk space to keep your livestream looking clean.
Customise To Your Creative Flow

No matter what kind of content you're creating, the RODECaster Duo can be configured to perfectly suit your workflow. Assign the eight inputs to any of the physical or virtual faders to suit your setup, customise the effects and processing for each channel, and transform the RODECaster Duo into your own personalised studio.
Take Creative Control with SMART Pads

The RODECaster Duo features six programmable SMART pads that give you huge creative control at your fingertips. Trigger sounds, music beds, or on-the-fly voice effects like reverb, echo, pitch and robot FX, send MIDI commands to external software, activate automated mixer actions like fade-ins and fade-outs, and so much more.

Connect Any Audio Device

No matter what your setup looks like, the RODECaster Duo offers complete flexibility when it comes to connectivity, making it the perfect control centre for your audio productions. It features two USB interfaces for dual computer setups, an MFi-certified USB port that works seamlessly with iOS devices, and you can record ultra-high-quality phone calls or stream audio in high-definition via the advanced Bluetooth connection.

Key Features:

Fully integrated audio production studio for podcasters and content creators
Ultra-low-noise, high-gain Revolution Preamps (-131.5dBV EIN, 76dB gain)
Two high-quality Neutrik combo inputs for connecting microphones, instruments or line-level devices
Seven individually assignable channels with four broadcast-quality physical faders and three virtual faders
Integrated wireless receiver for connecting RODE Series IV wireless devices (including the Wireless GO II and Wireless ME)
High-performance quad-core audio engine
Studio-grade APHEX audio processing and on-board effects
Six fully programmable SMART pads with bank switching
3.5mm TRRS input for connecting headphones and headsets
Dual USB-C interfaces for connecting two computers or mobile devices
Advanced Bluetooth connectivity for high-quality phone call integration
Designed and made in RODE's state-of-the-art facilities in Sydney, Australia

Specifications

Acoustic, Video & Electrical
Frequency Range: Mic Inputs: 20Hz - 20kHz, Monitor Outputs: 20Hz - 20kHz
Microphone Input Impedance: 4KO
Instrument Input Impedance: 1MO
Preamplifier Gain Range: 0 - 76dB
Equivalent Noise: -131.5dBV (A-weighted)
Line Output Maximum Level: 4dBu
Headphone Output Power: 250mW
Power Requirements: USB-C PD (9V, 3A)
Analogue Audio Output Connectivity: 2 x combo jack (mic, instrument, line), 1 x 3.5 TRRS headset jack (I/O)
USB Interface 1: 1 x 2-in/14-out multichannel device, 1 x 2-in/2-out with mix-minus
USB Interface 2: 1 x 2-in/2-out with mix-minus
Bit Depth: 24-bit
Sample Rate: 48kHz
Recording Storage: microSDHC, microSDXC, USB-C removable drive (exFAT - minimum 100MB/s)
Data Transfer: USB 3.0 SD card reader 130MB/s
Network Connectivity: WiFi 802.11g/n/ac 2.4GHz and 5GHz, Ethernet 100/100
Internal Storage (GB): 4GB (SMART pads)
OS Requirements: macOS 10.15 or later, Windows 10 Version 1803 or later, Windows 11

Mehcanical:

Weight (grams): 1131
Dimensions (millimetres): Length: 235, Width: 225, Height: 76

What's in the box:

1 x RODECaster Duo, 1 x USB-C to USB-C cable (1.5m), 1 x power supply

Notes: The New Standard in Octave Pedals

Fusing classic BOSS octave tones with the latest tracking technologies, the BOSS OC-5 sets a new standard in octave pedal performance. Vintage mode provides a spot-on recreation of the legendary mono OC-2 from 1982, while Poly mode offers numerous enhancements for extended-range playing. And with the addition of an octave-up feature, a span of three octaves is now available for creative exploration. From fat, low mono sounds to octave-shifted chords and more, the OC-5 delivers the widest range, finest sound quality, and best playability in any octave stomp to date.

OC-5 Octave Sound Tryout

Get interactive with our custom TonePedia player and explore hundreds of sound variations. Select your instrument, tweak and choose pedal settings.

High-Octane Octave Performance

Powered by the latest real-time processing technologies from BOSS, the OC-5 provides exceptional sound and playability for the most expressive octave experience ever. A key feature is the newly developed tracking engine, which delivers clean, accurate performance with no latency. The OC-5 also offers wider range and greater polyphonic capabilities than previous OC models, covering all your octave needs in one high-performance pedal.

Classic Tones with Vintage Mode

Introduced in 1982, the OC-2 was the world's first modern octave pedal for guitar and bass. Still loved by players everywhere, the stomp's warm-yet-present tone sits perfectly in a mix, and its characteristic voice can be heard in many famous songs. The OC-5's Vintage mode brings you the OC-2's iconic mono sound, coupled with improved response thanks to the new tracking engine. Dedicated level controls are provided for -1 and -2 octave effects and the direct sound, giving you quick access to an endless variety of sub-octave colours.

Enhanced Poly Mode

The OC-5 also features an evolved version of the smart Poly mode first introduced with the OC-3 Super Octave, letting you play full chords with octave effects. The variable Range knob restricts the effect to the lower notes on your instrument, perfect for playing octave bass lines alongside normal chords and melodies in the higher registers. And with the new tracking refinements, it's even possible to isolate the octave effect to the bottom note in a chord-just turn the Range knob to the "Lowest" setting.

Extended Range with Octave Up

Another cool OC-5 enhancement is the new octave-up effect, which is available in both Vintage and Poly modes. Simply twist the dedicated +1 OCT knob to bring in the desired effect level. Use the octave-up effect on its own for faux 12-string sounds and unique solo tones, or blend it with the octave-down effects for extended chord voicings and super-fat leads.

Guitar/Bass Switch and Direct Out

The OC-5 lets you instantly optimize the performance of its tracking engine for either guitar or bass via a dedicated switch on the body of the pedal. And with the Direct Out jack, it's easy to route dry and effect sounds to different destinations, such as two stage amps or discrete channels on a mixer or audio interface.

Specifications

Nominal Input Level-20 dBu
Input Impedance: 1 M ohm
Nominal Output Level: -20 dBu
Output Impedance1 k ohm
Recommended Load Impedance: 10 k ohms or greater
Bypass: Buffered bypass
Controls:
Pedal switch, GUITAR/BASS switch, VINTAGE/POLY switch, DIRECT LEVEL knob, +1OCT knob, -1OCT knob, -2OCT/RANGE knob
Indicator: CHECK indicator (Serves also as battery check indicator)

Connectors:
INPUT jack: 1/4-inch phone type
OUTPUT jack: 1/4-inch phone type
DIRECT OUT jack: 1/4-inch phone type
DC IN jack

Power Supply: Alkaline battery (9 V, 6LR61 or 6LF22), AC adaptor (PSA series: sold separately)

Current Draw: 60 mA

Expected battery life under continuous use: Alkaline: Approx. 5 hours
*These figures will vary depending on the actual conditions of use.

Accessories: Leaflet ("USING THE UNIT SAFELY," "IMPORTANT NOTES," and "Information")
Alkaline battery (9 V, 6LR61)
Options (sold separately) AC adaptor: PSA series

Size & weight

Width: 73 mm / 2-7/8 inches
Depth: 129 mm / 5-1/8 inches
Height: 59 mm / 2-3/8 inches
Weight (including battery): 440 g / 1 lb

Notes: Honey is a palm-sized, touch-based noise instrument based on the bytebeat principle. It runs on a single AAA battery and emits sound through a speaker. It doesn't have an audio jack. It creates dynamic sounds by manipulating variables and mathematical operations through touch.

The internal dynamic equations consist of five variables and four operations, with six possible operators for each operation. They are constantly changing and forming new equations, creating chaotic randomness.

If the unit does not respond correctly, the battery needs to be replaced.

Powered by one AAA battery

Notes: The Rene music synthesizer module is a powerful three-dimensional prism of composition. It is the world's only 3D Cartesian Music Sequencer. Named for the French philosopher & mathematician Rene Descartes, it uses the Cartesian coordinate system to unlock the analogue step sequencer from the shackles of linearity. The original Rene was a one-channel, two-dimensional Cartesian sequencer with limited memory, this new Rene is a three-channel, three-dimensional Cartesian sequencer with memory for up to 64 complete States. Considering the multiple channels and FUN programming options per multiple axis, Rene has become an n-dimensional matrix or tesseract of synthesizer sequencing.

Notes: This cable is designed to connect gear with XLR outputs to gear with XLR inputs. It is ideal for use in touring and other live-sound applications.

Hosa cables are built with the hard-working, hard-touring musician or audio professional in mind. Hosa cables are exceedingly popular, due in part to their reputation as being one of the most affordable and high-quality cable lines in the business. Hosa cables have also received praise for their durability and excellent performance. When it comes to audio cable design, Hosa keeps a steady eye on the basics, and you can hear this attention to detail in their sound. To make your next music experience extraordinary, pick up a Hosa cable today.

Notes: This pack of 6 guitar/audio patch leads from Chord is designed for connecting effects processors, sound modules, pedals etc. in coloured insulation. They are terminated at each end with a right angled 6.3mm jack plug.

Notes: A metal professional standard floor microphone stand with boom arm that is adjustable for height, angle and extension. The product features tripod style foldaway legs and has a remarkable stability when in use. The Boom arm extends 760mm.

Notes: Dual 1 x 3 buffered mult (one audio or cv signal in with multiple buffered outputs).

The output of the first mult is normalled to the input of the second mult to create a 1×6 buffered mult

Notes: Classic closed-back headphones in a low-impedance version designed to play nicely with outputs on phones, laptops and interfaces. One of the best all-round options for production.

Supplier's notes:
The Beyerdynamic DT 770 Headphones 80 Ohm are closed back dynamic headphones that use the same comfortable, sound isolating design as the 250 Ohm studio version, but with a lower resistance for general purpose and mobile applications. Because of the lower resistance, the DT 770 Pro 80 Ohm headphones are louder and work on low power devices such as smart phones, MP3 player, laptops and bus powered interfaces. Therefore, if you are working in a loud environment or using a battery operated device, the Beyerdynamic DT 770Pro 80 Ohm headphones make the perfect choice of headphone.

When out and about, you really need to block as much ambient noise out as possible and a lot of headphones do this by clamping the ear-pads as tightly to your ears as possible and using materials that absorb a lot of sound. This produces two unwanted issues; discomfort, after prolonged use; and a loss of audio quality as sound being generated by the driver is absorbed by the cup. The DT 700 Pro series avoids this by using a clever bass reflex system and a large circumaural cup design with velour pads. Of course the real technology is in the transducer itself, which produces a nominal frequency response of 5Hz to 35kHz and a nominal SPL of 96dB, an exceptional performance.

Notes: Units like the Akai MPC One sequencer are music-production powerhouses, they are the fulcrum of your setup and simply cannot go unprotected. This super durable polycarbonate shell offers protection from dust, spillages and accidental impact. Each Decksaver is trimmed precisely to fit, leaving cables in place. The Akai MPC One Standalone Music Production Controller Cover slides straight into a flight case or controller bag, perfect for transportation, and it also shields delicate controls and internal components from damage on the road, at home or in the club.

DIMENSIONS:

Weight: 0.76kg
Length: 28.2cm
Width: 28cm
Height: 3.9cm