Suchergebnisse: Dance Music

Notes: A Comparator is an electronic circuit that compares two voltages and switches its output to indicate which is larger. The Comparator operates between -10 or +10V

The Output is always -10V if below Threshold and +10V if above Threshold.

A Rectifier is an electronic circuit that is used to transform AC signals to an equivalent DC signal while removing one of it's polarities, i.e. Positive rectification excludes negative signals and vice-versa.
Both sections can be used to change the shape of any waveform as well as its harmonic content.

FRONTPANEL:
1 Comparator Threshold Knob
1 Comparator Jack Output
2 Comparator Monitor Led1 Common Signal Jack Input
4 Rectificated Outputs

MECHANICAL:
Format: Eurorack
Width: 4 HP
Depth: 2.5 cm

CONTROL VOLTAGE I/O:
CV inputs: i 10v
CV outputs: i10v

ELECTRICAL:
Max current: 30mA
Compatible with +-12v and +-15v power supplies
Bus Board Cable: 8 × 2 IDC (Doepfer style) connector

Notes: The ADDAC213B is the second pair of modules from ADDAC's Eurorack Bridge system.

A pair of ADDAC213Bs can be used in standalone to send/receive 8 CV or audio signals between different points inside the same case or as an expansion to the main pair of Eurorack Bridge modules, the ADDAC213As.

Two ADDAC213B modules can be connected to each other with the use of a single ribbon cable and then used inside a case to carry signals between distant points without the need for long cables. Less clatter, less spaghetti- more space of your fingers on those knobs!

ADDAC213Bs always come in pairs. A single pair can send & receive up to 8 CV or audio signals between different points in your case at the same time. The modules can be installed in normal position or a 180 degree position to fit any need.

As an Expansion to an ADDAC213A.

Each ADDAC213B connected to the backside of an ADDAC213A adds 8 more channels to the main bridging functionality of the ADDAC213A.

Up to 2 ADDAC213B can be connected to an ADDAC213A module, expanding the bridging between two difference cases to a total of 24 channels.

If you're looking for a simple one-cable bridge between your various cases, then look no further than the ADDAC213A.

Between the ADDAC213A pair and the ADDAC213B, your cases never looked so elegantly connected together!

Each module can be installed in normal position or at 180 degrees.

Comes with a 50cm ribbon cable. Custom sizes are available upon request.

Mechanical:
. Format: Eurorack
. Width: 3 HP
. Depth: 2.5 cm

Electrical:
Passive / Does not draw current
Ribbon Cable: 50cm or 100cm ribbon cable

Notes: This new module should not be judged by it's size, at 6hp it's packed with features.

At its core it features a noise source and two precision Sample & Holds with 0.01% of maximum deviation from the Input which allows for quantized signals to be sent through without any noticeable detuning or the typical voltage drops over time.

The Sample & Hold sections can also be used as a Track & Hold meaning it holds the incoming input while the Trigger input is ON and lets the input flow to the output when the Trigger input is OFF.
Each section also features it's own slew processor with a single control over attack and decay and an ON/OFF switch.

The noise signal is normalled to both sections inputs, meaning that without a jack plugged into the Input the sample and hold function will act upon the incoming noise signal generating random CV values.

The [Trigger A Alternate] switch allows to Link both sections so that any trigger input in Trigger A will alternate between triggering the A and B section.

Besides each section outputs there's also 4 extra outputs: Noise, Difference, Average and Sum. The Noise output is coming from the noise source, the Difference output is the subtraction of section A minus section B, the Average output is the sum of both A plus B and then divided by 2 and finally the Sum output is the sum of both A plus B sections.

MECHANICAL:
Format: Eurorack
Width: 6 HP
Depth: 4 cm

ELECTRICAL:
Max current: +50mA/-50mA
Bus Board Cable: 8 × 2 IDC (Doepfer style) connector

Notes: Following ADDAC System's T-Networks series, the importance of having the right input signal for firing drum modules or envelopes was realised. Gates and Triggers are often looked at as similar signals but at times it really makes a difference and results will change drastically depending if a Gate or a Trigger is fed to the input of such modules.

This led to the simple yet effective Gate to Trigger.
A four channel converter with bypass switch for each channel.

Any input Gate will be limited to a 1ms Trigger.

Tech Specs:
3HP
2.5 cm deep
10mA +12V
10mA -12V

Notes: Passive dual expression pedal attenuator.

Plug any CV or audio source through it and control its amplitude through any standard expression pedal.

Invert switch for inverting the expression pedal action.

Specs:
- Passive Module
- Width: 4 HP
- Depth: 3 cm

Notes: The ADDAC302 Nchunk Control module allows you to connect a Nintendo Nunchuck controller to your modular synth, featuring a two-axis thumb joystick, a three-axis accelerometer and two trigger buttons.

The module provides CV outputs for all of the Nunchuck's parameters and special functions to remap the CV outputs. The remapping can be both continuous or step-by-step and can be accessed through either the dedicated CV inputs or the manual controls.

A specially dedicated Mix output averages between the first two CV outputs, a very useful feature for continuous control parameters.

Mechanical:
- Format: Eurorack
- Width: 8 HP
- Depth: 4 cm

Control Voltage I/O:
- CV inputs: 0 - 10v
- CV outputs: 0 - 5v
- Gate in threshold: 2.5v

Electrical:
- Compatible with +-12v and +-15v power supplies
. Max current: 100mA?
. Bus Board Cable: 8 × 2 IDC (Doepfer style) connector

Notes: This is a complex Gate / CV generator based on probabilities.

Functions:

Knob 1:
%1 = Gate 1 Probability
5TG = Fifth Output Type: Trigger/Gate
N1 = Note 1 Tuning

Knob 2:
%2 = Gate 2 Probability
T.SIZE = Trigger Size
N2 = Note 2 Tuning

Knob 3:
%3 = Gate 3 Probability
DIR = LOCK Mode Direction: Backwards/pendulum/forward
N3 = Note 3 Tuning

Knob 4:
%4 = Gate 4 Probability
S.SIZE = LOCK Mode Sequence Size: up to 16 steps
N4 = Note 4 Tuning

Knob 5:
SWING X = Clock Swing X: 1 to 16
Y = Clock Swing Y: 1 to 16
N5 = Note 5 Tuning

Gate Outputs Behaviour:

At every clock input, based on the four knobs probability settings, the module will select one active gate out, only one of the five gates will be active at all times. All Gate outputs can also behave as a Trigger instead, Trigger size can also be adjusted.

The knobs set the probabilities of each gate to be chosen, here's an example of how this operates

With all first four knobs at 12 o'clock the first Gate has 50% of being the chosen one, the remaining 50% of the times will be passed through the next knobs. So Gate 2 at 12 o'clock has 50% of the remaining 50% left by setting one, which leaves it with 25% chance of being the chosen one, the remaining 25% will be passed through Knob 3 which will have 12.5% chance of being the chosen one, the remaining 12.5% will be sent to Setting 4 which will have a probability of 6.25%. The remaining percentage left by the 4 Settings will always be the probability of Gate 5, in this case the remaining 6.25%.

Here's a couple more examples.

All knobs at 12 0'clock
Setting 1 = 50% chance, 50% left for remaining settings.
Setting 2 = 25% chance, 25% left for remaining settings.
Setting 3 = 12.5% chance, 12.5% left for remaining setting.
Setting 4 = 6.25% chance, 6.25% left for Gate 5.

All knobs at 9 0'clock (aproximate values)
Setting 1 = 20% chance, 80% left for remaining settings.
Setting 2 = 16% chance, 64% left for remaining settings.
Setting 3 = 12.8% chance, 51.2% left for remaining setting.
Setting 4 = 10.24% chance, 40.96% left for Gate 5.

Tuning and CV outputs:

While in the Tuning page you can use all knobs to set the 5 pitches
When in tuning page knobs should be rotated one at a time!
While rotating the knobs the CV out 4 will be used as a monitor, the other 3 CV outs will be behaving normally.
The module detects which pot is being rotated and outputs the relative pitch CV on CV out 4 for all knobs.
While on this page the tuning will be quantized or not relative to the panel Quantize on/off switch. Even if this process is done in quantized mode the module always store the free value in order to allow quantisation to be turned off later.
Once you're happy with the tuning you can exit the page, new values are stores to memory while exiting the page.
When tuning the module detects both the note selected and the relative octave.

CV Outs behaviour
This will be easier to explain with examples

Let's say we tuned these notes:

C0 or 0v
D1 or 1.166v
F2 or 2.466v
G3 or 3.583v
A4 or 4.75v

1. Next Logic out calculated is gate 3.
CV outs 1-2-3 will output a note in octave 2, the note itself is randomised from the 5 tuned notes (C,D,F,G,A).
CV out 4 will output the exact note tuned with knob 3 (F2)

2. Next Logic out calculated is gate 5.
CV outs 1-2-3 will output a note in octave 4, the note itself is randomised from the 5 tuned notes (C,D,F,G,A).
CV out 4 will output the exact note tuned with knob 5 (A4)

Out 1-2-3 is octave related
Out 4 always output the original tuned note

Knobs Pages access:

MENU/TRIGGER button is used to access pages
After power up it gets to first page by default.

Page 1:
MENU/TRIGGER button is off and blinks with clock inputs

Page 2:
Pressing the MENU/TRIGGER button for 3 seconds the Button Led lights up meaning you're in Page 2, changing knobs will affect the secondary function.
Releasing the button jumps to Page 1

Page 3:
Pressing the MENU/TRIGGER button for 3 seconds the Button Led lights up, keeping it pressed without moving any knob for 3 more seconds makes the Button led go off. At this time you can release the button. After that the button will light up meaning you're in page 3, or the tuning page.
Pressing the button one time jumps to Page 1

Soft-Recall and Memory:

Knob positions are stored in memory while in operation to be able to have a soft recall of the settings, so when jumping from page to page you'll need to rotate the knob until you find the last setting and only then they start to operate. Whenever the pot crosses the last setting point the MENU/TRIGGER button will blink indicating that the knob is now active.

Page 2 & 3 have permanent memory so it will always load the last settings after power up.
Page one is volatile and powers up with the initial knobs settings.

Notes: Inspired and officially licensed from Teia's Stochastic Function Generator which was introduced in 2013 but is no longer available. This earlier version served as an inspiration, but with a completely rebuilt and reprogrammed mcu to a fully featured 4 voice 2 stage envelope and slew generator.

ADDAC System ADDAC506B VC Stochastic Function Generator Expansion Module (black faceplateADDAC System ADDAC506B VC Stochastic Function Generator Expansion Module (black faceplate
This expansion allows extra I/O to the ADDAC506, namelly:

Four trigger inputs for the random engine.

Four CV random outputs from the random engine.

Notes: The ADDAC603 VC Triple Bandpass Filter provides three channels of bandpass filters, fantastic for sculpting complex sounds. Each of the channels feature a gain/distortion control with switch to select between x3 or x100 gain, which can cause the input signals to distort, adding another layer of harmonic interest.

The inputs are cascaded together to allow for one source to be filtered three different ways - or each filter can be used independently. The three filters also feature controls for frequency, which sets the cutoff point; width, which sets the width of the band that is being filtered; feedback, which at high settings causes the filter to self-oscillate, and level control, which sets the amplitude of the output. Frequency, bandwidth, and output level each have CV inputs with attenuverters.

A switch sets whether the filter is 24 dB or 12dB per octave. There are individual outputs with phase switch, plus a mix output and dry/wet output with adjustable control for mix balance. This module provides a wide variety of filtering options to add complex tonal shaping to your rack.

Tech Specs:

22HP
3.5 cm deep
250mA +12V
250mA -12V

Notes: This module was developed upon the Tubaz Filter which was released in 2014 by Gotharman but is currently no longer in production. We loved the original module so much that we officially licensed it's circuit and expanded it to feature several new functionalities.

Here's a paragraph from Gotharman regarding the original design:
"I designed it with the purpose of adding crunch, edge and distortion to my eurorack system. It is not an ideal bandpass filter, that cuts off all frequencies above and below the center frequency.
Because of its high drive, there are, in most cases, some bleedthrough of the harmonics, that should have been cut off. You might consider calling it a "Band Add" filter. The main purpose of it, was to add edge, not to be a perfect bandpass filter."

While everything he mentions is still true we believe he was being modest, It's a dirty, gritty, growling and whining monster which promises you some of the most peculiar filter sounds you'll ever hear.
However do not classify it as a "weird" distortion unit just yet because besides this hairy character it can be easily tamed (using lower volume levels) and then, with some care and intention from the user, it will transforrm itself showing it's feline purrrrr and cuddle sweet and caring, or like any good mut, showing up at night all happy, wet and dirty from a full dog's day and will lay down at your feet while wiggling it's tail howling as yawning just happy to be back home.

As such, standard volume principles do not quite apply to these units, the Audio Levels will go up to x2 amplification, Drive will go up to x11 and master outs go up to x2. The combination of these will cover all diferent qualities it can present. Overall sound can be distorted pre-Tube (raising input levels), in Tube (raising drive) or post-Tube (raising Out levels).
Higher Inputs and Drive will always be gritty, lower Inputs and Drive volumes together with higher Output levels will make the overall behaviour more mellow and closer to what a typical filter would behave like.

No standard expectations should be considered when acquiring these units, all of the tubes were built in the 70's and were bought from various sources, we always kept the premise that no tube was a bad tube (unless not really workinng) so due to each specific characteristics no module will sound exactly the same, making each unit particularly unique. This uniqueness will be particularly evident on their resonance/self-oscilating timbre as well as in their own microphonic qualities.

Regarding power and current draw, the module is designed using a low power tube, so it won't starve your eurorack power supply.

Tech Specs:
12HP
3.5cm deep
90mA +12V
60mA -12V

Notes: All you could ever dream of from an Eurorack console, and then some!

The ADDAC807A VC Stereo Summing Mixer offers you the power, the flexibility and the gorgeous layout of a high-end audio console, in the popular Eurorack format. Starting off at 5 stereo channels, with the option to add 4 additional stereo channels via the ADDAC807C Expansion Console, its send/return options and clever matrix will ensure you have that perfect mix down in seconds. Customary to ADDAC System designs, there is enough CV control and hands-on switch options to make the ADDAC807A into an instrument in and of itself.

The ADDAC807A is accompanied by its sibling, the ADDAC807B Inputs Console. We decided to allow the user to freely define the placement of the jacks by separating the area where all your cables are located. Less clutter means more hands-on control and higher playability. The ADDAC807B Inputs Console holds all the jack inputs for the ADDAC807A Main Console, along with CV inputs and additional channel settings - 'cause you can never have enough switches!?

Module is sold together with the ADDAC807A, which also provides power. ADDAC807A price is for both the 807A and 807B.

Notes: Dedicated expansion for the ADDAC807C VC Summing Mixer

Features 4 individual track post fader stereo outputs.

2Hp
2 cm deep
0mA

Notes: Complex gate and CV generator designed as a trigger source and modulation tool. Based around four sine wave LFOs that mix together and interact to create ever-changing patterns.

Supplier's Notes:
In 2009 John Berndt coined and defined the term Relabi in his essay "Relabi": Patterns of Self-Erasing Pulse, these are his own words: "Relabi, Def.: The experience of a palpably coordinated plurality of events that appears to be cyclical but simultaneously suspends identification of a uniform pattern, preventing a resolved sense of pulse. Relabi therefore seems equally pulsed and unpulsed at the same time. It is an experiential gestalt, a quality of experience, greater than the sum of its parts (it forms a sustained unity in experience, albeit of a new kind)."

He also makes the question: "Why would anyone want this Relabi experience? I maintain that much of what is exciting in musical forms involves an interplay between the setting up and denying of pulse expectations."

Inspired by this idea, ADDAC System developed this module that is both a gate/trigger and cv generator that can be freely used to trigger events or act as a complex modulation source. Four Sine LFOs are internally generated, each has controls for gain, frequency and mute(off). These 4 LFOs are then mixed together to generate what Berndt named the "Relabi Wave" this "wave" becomes a complex bipolar CV source. This i5v bipolar "wave" can be monitored on the 2 dedicated leds and is also available at its own Output.

Make sure to check the User's Guide for indepth description, working behaviour and diagrams.

Tech Specs:
10HP
4cm deep
100mA +12V
40mA -12V

Notes: One of the most impressive granular synthesis approaches in Eurorack, combining looping and granular effects with buffer sizes up to five minutes. Hugely creative and powerful dual-module setup.

Supplier's Notes:
There's a long history behind the granular concept and many reinterpretations of it's core principles, this is ADDAC's take on it.

In a loose description digital Granular refer to pieces of sound files being played at the same time with slight or completely different parameters originating what is commonly referred to as granular clouds. Normally there's a buffer size from which the granular engine snips it's pieces from and plays them according to the parameters set. This buffer size is normally small in size where grains are so small that can reach the hearing spectrum and be heard as a sort of ever changing complex wavetable, this is the principle behind granular synthesis.

ADDAC have added the possibility of long buffer sizes up to 5 minutes, allowing "softer" approaches to the granular principle using it as an effect that can generate from "accidental" effects like slight "stutters" to extreme processing and transformation of any incoming audio signal.

This module is conceptually deep but easy to grasp and operate as all controls are in its dedicated panel, all jack inputs and outputs have its own separate panel to allow no compromise when playing it's controls.

There are three main sections in this module:
Looper Engine: The Looper is where all the Real-Time recording happens. The audio input feeds the recording buffer, multiple controls allow to record and play loops into a list so that any sample in the list can be accessed at ay time and more acting as a standard looper
Granular Engine: The Granular acts upon the buffer of whatever LOOP is selected.
Output Mix The output mix allow individual control for the Dry Input, Looper Volume and Grains Volume.
Besides these main sections there's also a simple strip down MENU mainly used to LOAD and SAVE Banks, no Menu diving guaranteed.

For more detailed info, please refer to the User's Guide.

Audio Specs:
Audio input: Stereo, 16bit 44.1Khz
Audio output: Stereo, 16bit 44.1Khz

Tech Specs:
32HP + 13HP
4.5cm deep
240mA +12V
70mA -12V

Notes: Revised take on the excellent Benjolin dual oscillator and filter from Rob Hordijk, featuring the 'rungler' stepped CV generator and extensive output options.

Supplier's Notes:
Benjolin V2 - Rob Hordijk's latest revision of the classic Benjolin. The core of the Benjolin continues to be two oscillators, the rungler (stepped CV generator), and a multimode filter.

This latest revision adds:

Reworked oscillator and filter sections

All levels are adjusted to eurorack standards

Two different steps modes (8/16 and 127)

Double and single clock rate

Externally clockable

External filter input with blend control

Notes: A 6HP version of Mutable Instruments Peaks that adds CV inputs and attenuverters for each of the four parameters.

It can be an ADSR-style envelope generator, an LFO and a drum emulator. By default, the Dead Man's Catch (DMC) firmware will be loaded, which adds the Alt ENV, ALT LFO, ALT Tap, Alt Drum modes below.

The module is calibrated, comes with a power cable, and a one year warranty.

Additional Dead Man's Catch firmware modes:

Basic (original modes):

Envelope
LFO
Tap LFO
Bass/Snare Drums

Alternative ENV:

Double attack envelope
Repeating attack envelope
Looping envelope
Randomized AD envelope
Bouncing ball envelope

Alternative LFO:

Frequency-modulated LFO (folded sine FM)
Frequency-modulated LFO (random FM)
Varying wave shape LFO ( folded sine WS mod)
Varying wave shape LFO ( random WS mod)
Phase-locked loop oscillator

Alternative TAP Mini-sequencer:

ModSequencer
Pulse Shaper
Pulse Randomizer
Turing Machine
Bytebeats

Alternative DRUM:

FM drum Generators
Randomized bass and snare drum generators
Randomized high hat

Notes: This is a buffered/active mult with LED indicator. You get two channels of 1 to 3 multiples within a 2HP module. The output of channel 1 is normalled to channel 2 so it can also be treated as a 1 to 6 multiple as well.

Active vs Passive mults:

With a passive mult you are effectively just plugging multiple things into the same jacks. This will often cause some voltage drop in each of the signals. With an active (or buffered) mult you will not get any voltage drop from the original signal.

Comes with a black and gold panel, power cable and one year warranty.

Usage note:

The red stripe of the power ribbon cable goes towards the top of this module.

Notes: Mult 1U Intellijel Format

This is a buffered/active mult with LED indicator. You get two channels of 1 to 3 multiples within a 2HP module. The output of channel 1 is normalled to channel 2 so it can also be treated as a 1 to 6 multiple as well.

Active vs Passive mults:

With a passive mult you are effectively just plugging multiple things into the same jacks. This will often cause some voltage drop in each of the signals. With an active (or buffered) mult you will not get any voltage drop from the original signal.

Comes with a black and gold panel, power cable and one year warranty.

Usage note:

The red stripe of the power ribbon cable goes towards the top of this module.

Notes: Popple is an 8hp multimode stereo filter based on the Mutable Instruments Ripples V1 filter section. Popple maintains the buttery smoothness of Ripples filter while giving you two separate audio paths. The audio paths share a resonance, control, a frequency cutoff control, resonance CV input, and a v/oct cutoff CV input. Each channel then has it’s own cutoff CV input with attenuverters (which are normalled to a 2.5V signal).

Popple will also self-oscillate at high resonance settings, when coupled with the v/oct CV control, it can also act as a dual sine wave oscillator.

Notes: The full power of Mutable Instruments Elements packed into 18hp. It features jack lights that can be turned on/off via a jumper on the back. This module comes loaded with the most recent firmware, with the new Chords mode that unlocks a whole new world of potential.

Based on open source designs by emilie gillet under Creative Commons (CC-BY-SA) license.

Width: 18hp
12V: 130mA
-12V: 10mA

Notes: Third-party clone of the open-source Mutable Instruments Plaits oscillator/sound source. All the same functionality in a compact 8hp format with full-size knobs for the key functions.

Supplier's Notes:
Functionally identical clone of the Mutable Instruments Plaits. Beehive strikes a nice balance between size, reducing 12hp down to 8hp, and playability by offering full size knobs for the four main functions. Beehive also retains the same depth of the original module at 25mm. This module uses After Later's new aluminum knobs which have a nice non-slip texture and allow for more finger space over the standard 1900H Davies knobs.

Notes: Cara (uMarbles)

This is a new build of a micro version of Mutable Instruments Marbles. It retains all the functionality of the original full-sized module but takes up less space. It comes with jack lights that can be disabled via a jumper on the back.

These modules use tall bushing potentiometers to offer a more stable feel. You can see the difference in the last picture. You will feel much less wiggle with the tall bushing (left) than with traditional trimmer style (right).

The module is fully assembled, tested, and calibrated. The calibration is done with a 6.5 digit multimeter, itself recently calibrated, to ensure you get the highest accuracy from your module. Eurorack power cable included.

Width: 10HP
Depth: 34mm
Height: 3U
Power Consumption: +12V: 80mA -12V: 20mA

Notes: DVCA

DVCA is a dual VCA based on the Mutable Instruments Veils. It features two separate voltage-controlled amplifiers, both with a gain and a response curve potentiometer, that is variable from linear to exponential. The outputs are normalized, so when no patch cable is present on output 1, output 2 will contain both signals, allowing the module to be used as a mixer. Several DVCAs can be daisy-chained for voltage-controlled mixer operation. It comes with jack lights that can be disabled via a jumper on the back.

These modules use tall bushing potentiometers to offer a more stable feel.

The module is fully assembled and tested. Eurorack power cable included.

Notes: Enigma Expander for micro Turing Machine (Alan)

An expander for After Later's Alan module (a smaller version of the Turing Machine) that enables you to manipulate the stepped CV sequence. This enables you to create a different, yet related sequence to the main Alan output.

The module comes with the required cable to connect to the main module. Our black and gold panel is designed to complement Alan, Aftter Later's micro version of the Turing Machine.

The module comes with a 1 year warranty.

Notes: This is a new build of a micro sized Mutable Instruments Plaits called Knit.

These modules use tall bushing potentiometers to offer a more stable feel.

The module is fully assembled, tested, and calibrated. Eurorack power cable is included.

Width: 6HP
Depth: 25mm
Height: 3U
Power Consumption: 12V: 50mA -12V: 5mA

Notes: This is a new build of a Monsoon, which is a variation of Mutable Instruments Clouds with separate CV and controls for the 4 "blend" functions. The 4 LEDs on the sliders indicate incoming control voltage for the 4 main parameters. The button which was used to select blend parameters now simply switches what the 4 LEDs display (audio input monitoring or monitoring the 4 blend amounts.) Parasites 2.01 firmware is loaded by default. Alternative firmware can be loaded by request.

The module is fully assembled, tested, and calibrated. Eurorack power cable is included.

Width: 12HP
Depth: 22mm
Height: 3U
Power Consumption: +12V:120mA -12V:10mA

Notes: Morcom Expander for micro Turing Machine (Alan)

An expander for After Later's Alan module (a smaller version of the Turing Machine) that exposes the pulse outputs from the main Alan module. You get 7 seven random outputs and then 4 that are derived from other 7 outputs. When 1 and 2 are high then the 1+2 outputs is high. You can get some great rhythmic effects using these in conjunction with the main stepped CV output.

The module comes with the required cable to connect to the main module. The panel is designed to compliment Alan, After Later's micro version of the Turing Machine.

The module comes with a 1 year warranty.

Notes: nRings

This is a new build of a micro version of Rings from Mutable Instruments. MicroRings, also called NanoRings, retains all the same functionality as a full-size Rings module.

The module is fully assembled, tested, and calibrated. Eurorack power cable is included.

These modules use tall bushing potentiometers to offer a more stable feel.

Notes: This is a brand new build of a JakPlugg designed Pachinko, which is a micro version of Mutable Instruments Marbles. It retains all of the functionality of the original but takes up less space (12HP) than the original Marbles (18HP).

The module is fully assembled, tested, and calibrated. The calibration is done with a 6.5 digit multimeter, itself recently calibrated, to ensure you get the highest accuracy from your module.

The panel is a custom black After Later Audio panel that offers metallic gold accents.

The module comes with a power cable and a 1 year warranty.

Notes: Pique (uPeaks)

Pique is a micro version (4HP) of the popular Peaks module from Mutable Instruments. It can be an ADSR-style envelope generator, an LFO and a drum emulator.

The module is calibrated, comes with a power cable, and a one year warranty.

Notes: Pique (uPeaks) 1U Intellijel Format

This is a 1U (Intellijel format) version of the Pique module which is based on the popular Peaks module from Mutable Instruments. It can be an ADSR-style envelope generator, an LFO and a drum emulator.

The module is calibrated, comes with a power cable, and a one year warranty.

Notes: This is where Storm and Monsoon meet to create the latest improvements on the original Clouds design. With Typhoon you get all of the features of Storm combined with sliders and layout of Monsoon in 16hp. Typhoon runs the SuperParasites firmware, so no more having to swap between Parasites and Kammerl firmware options. Some of the notable features are:

Dedicated blend controls for Feedback, Panning, Mix, and Reverb (similar to Monsoon)

All eight modes from Parasites and Kammerl

Stereo VCAs

input/output mutes

Exponential and linear pitch controls

Universal CV routing and random CV signals

Comes with an exclusive black and gold panel, power cable and one year warranty.

Notes: uBurst

This is a new build of the micro version of Mutable Instruments Clouds. The module retains all the functions of the original Clouds, taking up significantly less rack space.

These modules use tall bushing potentiometers to offer a more stable feel.

The module is fully assembled, tested, and calibrated. Eurorack power cable is included.

Notes: uO_C

This is a new build of Micro Ornament & Crime, a variant of the popular Ornament & Crime designed by mxmxmx. The firmware is Stock by default.

The module is fully assembled, tested, and calibrated. The calibration is done with a 6.5 digit multimeter, itself recently calibrated, to ensure you get the highest accuracy from your module. Eurorack power cable included.

Notes: This 30HP wide module features twelve fixed frequency, inductor based bandpass filters, set at half octave interval spacing and covering from 125 Hz through to 5.8kHz. It also features low pass and high pass shelf filters, again they are fixed frequency and both are active inductor based circuits. It has a vintage pedigree that harks back to the original and highly sought after 914 Fixed Filter bank from the 1960's Moog 900 series modular synthesiser system, however we have brought this design up to date and made it compact enough to fit into skiff friendly Eurorack cases by using gyrator based active inductors, and have added some other very useful features too - the bands are split alternatively to left and right channels, each having their own individual output, and there is also an inbuilt Voltage Controlled cross-fader that allows panning between the left and right banks, with a mix of all bands available in the central position.

In addition, we have a second cross fader that can mix between the dry incoming signal, or an external signal fed into input 2, and this is cross-faded against the wet MIX Output - this allows Voltage Controlled crossfading from wet to dry signals, or between wet and external signals - and the level of each can be adjusted using the Input 1 and Input 2 level controls.

A further addition is the feedback control, this is similar in design to the resonance control on a regular VCF, but because of the multiple fixed filters topology it is rather different in operation - it would normally be added in small amounts to thicken up the sound, however we have allowed the feedback to traverse to quite extreme settings for howling feedback and even soft clipped self-oscillation, especially for the noise merchants out there...

Using L/C inductor topology bandpass circuits rather than the usual Sallen Key R/C active bandpass filters does give a slightly different sound and this is part of the magic of the original 914 filterbank, as the LC based circuit exhibits less phase shift against frequency that the more common Sallen Key R/C based bandpass filters that are used in many Modular synths.

Many people often wrongly assume that a fixed filter bank is exactly the same as a graphic equaliser - however this is certainly not the case, if all of the controls of a graphic EQ are set to centre then a flat frequency response is expected and the output will sound very similar, or identical to the input - this does not happen with a fixed filter bank, the frequency response rises and falls as it passes between each stage (but to a lesser extent than if the filters are all set to maximum output), so it acts as a soft slope comb filter, and the resulting output sounds very different from the input signal. Also, with all of the individual filters turned to zero there will be no output at all.

Notes: The original MiniMod Glide +Noise module was based exactly on the original Minimoog Model D circuitry, which was designed to be used with the built in Model D keyboard, and because of its vintage design its range was severely limited to 5 or 6 octaves, and it also responded to positive voltages only. Another limitation was that it would not return fully to zero when selecting long glide times, which restricted the range even more.

So we made the decision to re-design the MiniMod Glide + Noise using modern precision parts, and we have come up with an all new circuit which has exactly the same function, but with a hugely extended range. It has the same Glide slope characteristic (a slightly curved Linear Glide) as the Model D on which the MiniMod is based, however in response to many requests from customers we have adjusted the glide up and down speeds so that they are now very similar , which is much more useful in real world applications that the earlier MK1 version which (like the Model D) would glide up considerably faster than it would glide down.

The new Mk2 MiniMod Glide Noise module now has an impressive 14 octave range, and can respond to negative voltages down to -5V. This is a very useful feature, as our MiniMod VCO's will respond to negative control voltages and produce correspondingly low frequencies; so it is now possible to glide down quickly or slowly to crazy sub bass levels! The hold feature has been improved too, it covers the full audio range as well as DC control voltages, and works as a track and hold module with Eurorack signal levels.

A further enhancement is that the Mk2 module can now (using selectable jumpers) transmit or receive pitch CV to the Eurorack power bus; for example, the Glide CV Output can now be directed to the Bus in order to send CV's to (for example) three VCO's via the bus without the need for a passive multi and four patch cords!

The Noise section of the module is unchanged, except that we have slightly boosted the level of the Red Noise output to bring it more in line with Eurorack control voltage levels.

Lastly, it is much shallower - Mk1 Glide Noise had a depth of 54mm, and it was the only MiniMod module that was too deep to fit a skiff style case - and this prevented a full MiniMod system being installed into a shallow Eurorack case. The new MK2 version is only 28mm deep, so this allows both it and a full MiniMod system to be mounted into shallow skiff style Eurorack cases.

Dimensions: 6HP wide, 26mm Deep
Current draw: 36mA Positive, 38mA Negative

Notes: The WaveSwarm is a waveform animator and all analogue dual channel device.

Each channel simulates up to six VCO's beating in unison with a different beat frequency between each animation. The fixed beat frequencies are generated by twelve onboard LFO's, and the front panel pots control the level of each of the six animators, along with the level of the dry signal to the final mix. In addition to independent channel inputs and outputs it also has an A+B output, which sums the outputs of the two channels, creating an effect similar to twelve VCO's in unison! This is possible because channel B uses slightly different beat frequencies to channel A, they are not identical.

The input waveform can be saw, triangle, sine or wavetable/complex waveforms, in fact most waveforms with the exception of square or PWM waves will give some form of animation.

A soft clip circuit is built in so that at higher signal levels the signal magnitude is limited by rounding the top and bottom of the waveforms, thus slightly softening the sound. There are soft clip LED indicators for both channels.

It can produce huge, fat drones or supersaw type waveforms from a single sawtooth or triangle wave input.

Notes: Perfect for adding that final touch to a modular patch, the AJHSynth Finaliser R-EQ module includes seven Mono / Stereo reverb types, along with a four band equaliser and a Sonic Maximiser / Enhancer.

The Reverb, EQ and Maximiser can be used in Mono IN, Mono OUT mode or Mono IN, Stereo OUT modes. The reverb alone can also be used in Stereo IN / Stereo OUT mode too.

The fully analogue four band Equaliser includes three parametric equalisers for Low, Low Mid and High Mid ranges, and the High EQ has switchable shelving of either 2kHz or 5kHz. The Low EQ also includes a shelving mode.

The Maximiser is a fully analogue circuit too, with low and high treatment bands which change the phase and amplitude relationships of the sound to add punch and harmonics and really bring the sound to life in the mix.

The Reverb engine is based on 20 year old DSP technology, harking back to the reverb units which were used extensively on many synth and EDM tracks a couple of decades ago. We have added full control of reverb wet / dry mix, either manually or under CV control.

Notes: AJH Synth have had quite a few customers asking if we can make the gain jumpers on the MiniMod VCF and VCA modules accessible from the front panel, so this 2HP module aims to address this.

The Gain Switch Multi has two switches which connect to the gain jumpers on the VCA and VCF. Switch "up" is the same as having the gain jumper in place, switch "down" is the same as removing the jumper, and gives higher gain.

Using these switches gives a similar effect to the old "headphone out to external input" trick on the original Model D but with a much wider overdrive range, particularly from the VCA.

As an added bonus, AJH Synth have also included a six way passive multi.

Notes: This is a precision active buffer and multiple. This module has outstanding performance: it features very high input impedance, very low output impedance and an offset voltage of <1mV.

Not all active multi's are born equal, some designs do not fully solve impedance mismatch and tracking problems, or they apply offset voltages to the output and in rare cases can cause more problems than they solve!

AJH Synth have added a very useful (and unique) feature to cure tracking problems: four of the five outputs can be adjusted up or down by +/-5% from the front panel, so that VCO's and VCF's that don't track 1V/Oct exactly can be easily compensated to track correctly without having to re-calibrate the VCO or VCF themselves.

Notes: Two independent Contour Envelope Generators in a single 12hp wide Eurorack module. These are very accurate replicas of the Model D contour generators, with identical circuitry and component values running on the correct +9.3V and -10v supply voltages of the original; so they exactly replicate the original envelope response along with all of it eccentricities. Extra features include manual trigger buttons and envelope status LED's.

The contour generators played a larger part in the sound of the Model D than many people realise. There are two factors that make them unique, firstly the exponential slope when is used in conjunction with the (near) linear slope of the original VCA which is responsible for the famous Model D "punch". Secondly, the re-trigger behaviour is quite unique, multiple retriggering increases the output level so that either the volume increases incrementally, or the filter opens incrementally with each extra key press.

AJH Synth have added independent Decay switches for each individual Contour Generator rather than the shared switch on the original synthesiser, these switches change the Contour response from AD (switch up) to ADSD mode (switch down).

Notes: Sometimes real precision is required with pitch control voltages - this module features a super accurate "Cal" output, which is accurate to <1mV over 20V, translates to one cent over 20 octaves! It is ideal for calibrating the scaling of VCO's, indeed we have been using our own version of this circuit to calibrate our own MiniMod VCO's for the last three years.

As well as being a precision voltage source it is also a very accurate voltage adder, it has two channels (A & B) and both full volts (octaves) or 1/12th volt increments (notes) can be either added to or subtracted from the incoming signal. Perfect for adding a voltage offset to the output of a sequencer or it can be used to add switchable octaves to a VCO which only has course and fine tunes controls.

It also has a "mix" output, which allows either A channel on its own, or with the three way toggle switch channel B can either be added to, or subtracted from channel B, and this is in addition to the addition and subtraction per channel mentioned earlier.

Dimensions: 10HP wide, 26mm Deep

Notes: Really clever noise-based oscillator from AJH. Drones, sweeps and bleeps aplenty, ranging from tamed to out-of-control filth. Also doubles up as a more conventional ring mod and distortion module.

Supplier's notes:
This 14HP wide module is a voltage controlled noise based oscillator, or noisillator for short. It generates 1/f noise and this is then sent through a feedback loop which allows the noise to be "tuned" to varying degrees depending on the settings of the frequency and resonance controls, or incoming frequency or resonance CV's. The tuned circuit can be FM modulated too, for some thunderous sweeping sounds. We have bright and dark outputs, which are pre and post filter respectively. The Bright output will always have a degree of noise present in the signal, whereas the Dark output can be tuned noise only when 4 pole resonance is selected. We also have an external Sync input, which will reset the resonant waveform, and we also have an Audio input, so that an external signal can be mixed into the resonant loop. Combinations of external waveforms to these two inputs can create some massive drone sounds, or sweeping sync sounds.

There is also an XOR ring modulator, which can be used as a module in its own right too. Lastly, we have an XOR amplifier, which is another independant circuit that can be used to add noise and distortion to any audio signal.

Notes: Five-channel mixer with mutes, built-in VCA, switchable overdrive and LED level meter. Simple, straightforward, high-quality stuff from AJH.

Supplier's Notes:
The MiniMod Muting Mixer & VCA is a 10HP wide, five channel audio mixer with many useful features. It is available with either a black (Dark Edition), or a silver front panel.

The mixer section has five input channels, and each channel includes a bi-colour tactile LED switch that can instantly mute or un-mute the channel, replicating the oscillator on/off switches on the original Model D synthesiser. This arrangement is more convenient than regular switches as each illuminated switch shows the on/off status of the associated channel and multiple buttons can be pressed at once, making it very useful for live performance.

AJH have also included a four segment LED level meter so that the overall level can be seen at a glance and adjusted to prevent the output from getting too "hot" and causing distortion in other modules further downstream.

It also features a VCA that is integrated into the output section, and this can be switched from linear to exponential response - this allows it to be used as a voltage controlled sub mixer or as a stand alone VCA with five inputs.

Lastly, AJH added a wonderfully soft and warm sounding overdrive circuit that can be switched in to add smooth, tube like distortion. This works in a similar fashion to a master volume guitar amplifier, so the amount of overdrive can be varied widely with different settings of channel and master output levels.

Module Width: 10hp
Module Depth: 26mm (Including power lead)
Current Usage: 55mA Positive, 25mA Negative

Notes: 'Beast's Chalkboard' is dual channel stepped voltage source and adder for your eurorack modular synthesizer system. It primarily is intended as a dual octave switcher for VCO's but has many other uses including sequence transposition, FM ratio creation, buffered CV distribution and VCO calibration.

Technical Specifications:

Supply: +/-12V (Reverse voltage & polyfuse protection)
Current Draw: ~30ma
Size: 6 HP
Depth: 22mm (including power header)
Offset Error: +/- 10mV

Notes: The 'S.B.G' is a compact utility module intended for the interfacing of guitar effect pedals with your eurorack modular system.

It provides both attenuation and amplification of audio signals for level matching together with a crossfade control to conveniently adjust the wet/dry mix of a processed signal. The module also offers regulation of outgoing CV signals for safer use of pedal expression inputs.

Technical Specifications:

Supply: +/-12V (Reverse voltage protection)
Current Draw: ~30ma
Size: 4 HP
Depth: 22mm (including power header)