Synth modules

Notes: Crystal-clear clock-synced delay for loop up to 90 seconds, echoes, sound-on-sound, Karplus-Strong etc.

Features:
Loop or echo time is synchronized to a clock
87 seconds of delay/loop time maximum
48kHz/24-bit sampling rate, loop recorded at 16-bit (24-bit optional)
Extremely quiet, low noise and low jitter design
Tap tempo button and clock Ping input set the basis for one "beat"
Delay/loop time set as a number of musical beats (or fractions of beats) using the Time knob, switch, and CV jack
Sample-accurate clock output for perfect synchronization
Loop clock outputs for each channel
Time switches change range of Time knob from 1/8th notes up to 32 bars
Digital feedback, up to 110%
Delay Feed control, independent of dry/wet signal mix
Infinite Hold mode disables recording input and fixes regeneration at exactly 100%
Reverse mode plays memory contents backwards
With an infinite loop locked, knobs or CV can "window" around memory, by shifting the loop
Trigger inputs for toggling Infinite Hold and Reverse
Send and Return for applying effects to feedback with external modules
CV jacks to control Time, Level, Feedback and Dry/Wet Mix
16HP Eurorack module

Specs:
48kHz, 24-bit low-noise hi-fidelity
Up to 90 seconds of loop time
16HP
+12V: 110mA
-12V: 45mA

Included with the Looping Delay:
16-to-16 pin power cable
4 x M3 Knurlie screws

Notes: Great value from 4ms's twist on the Stereo Triggered Sampler module, this time capable of playing and manipulating stereo or mono WAV files from an SD card.

Supplier's Notes:
The Sampler is a variation of the Stereo Triggered Sampler.

Record, play and loop stereo .wav files with an SD Card. Includes the same 2022 Sampler Pack from the Stereo Triggered Sampler.

Features:

The Sampler plays stereo or mono .wav files from an SD Card. Samples are arranged into banks by placing .wav files into folders (each folder is a bank). A maximum of 10 samples can be loaded in a bank. There is a maximum of 60 banks (600 samples maximum total).
Sample files are limited to 4GB each, which is over 6 hours at 44k/16b/stereo.

Hundreds of samples included on microSD card
Extremely quiet, low noise and low jitter design
Stereo or Mono output

A knob and CV jack selects the Sample to play, and the Start Position knob and CV jack control where in the sample playback will begin. The Length knob and CV jack determine how much of the sample is played back: from tiny grains, to percussive hits, to longer loops... or just the entire file.

Pressing Play or firing a trigger into the Play Trig jack will play the sample. Holding the Play button down for a second will toggle looping.

There's also a Reverse button and jack for backwards playback, and an End Out jack for synchronizing loops, or cascading sample playback with other events.

To record samples, hold Play and Reverse for two seconds. Press Play again or fire a trigger into the Play/Rec Trig jack to start and stop recording. Each recording will create a new stereo 48kHz 24bit .wav file in the current bank's folder. Recordings can be as long as your card has the capacity for: a 256GB card is 18 days of continuous recording (432.9 hours). Audio data is split into maximum 4GB wav files on the microSD card.

Play button/trigger jack: Tapping the button or receiving a trigger starts/re-starts the sample
Sample CV/knob: select which sample within the channel's bank
Pitch CV and Pitch knob: playback pitch (-10 to +4 octave range)
Start Pos CV/knob: position in the sample to begin playback (loop start point)
Length CV/knob: playback time (loop end point)
Length knob at max: entire file is played
Length knob 50%-99%: 200ms - 5s of the sample is played (beginning at the Start Position)
Length knob <50%: Percussive decay envelope is applied to the playback (attack-only envelope if playing Reverse)
Length <1%: Tiny grains are played (can be used to sweep through sample file data manually)
Reverse button/jack: toggles forward/backwards
Bank button: selects channel's bank
Reverse + Start Pos button/knob combo allows for setting volume of playback
Maximum file size for playback: 4GB per file (6.7 hours per file at 44.1kHz/16b/stereo)
microSD Card is hot-swappable when Busy light is off: no power-down required to change cards.
Samples that are pre-loaded into memory can continue playing while card is swapped.

File Organization:

Using a computer, the intuitive automatic bank loading features make dragging and dropping your entire sample library a snap. No files need to be renamed. Just create folders and put up to 10 samples in each. If you want a folder to be associated with a particular colour of the Bank button, name the folder a colour name (such as "Blue - Loops").

Ships with a high-speed 16GB microSD card, loaded with hundreds of samples created for 4ms, from musicians such as Richard Devine, Wobbly, Moor Mother, Robert Aiki Aubrey Lowe, Joseph Pailo, Russell E.L. Butler, Hugo Paris & Marc Kate, Paul Barker, Baseck, Animal Collective, Cristian Vogel, Jay E, Marcus Fischer, Chris Carter, Daedelus, Nero Bellum, Anna Sitko, Thomas Fang, Bogdan Raczynski, and more (Sample List)

Intuitive bank/colour organization system; no need to rename your wav files
Record new samples directly to a bank with the Record Input jacks...
... or drag your folders of sound files onto the microSD card, and each folder will become a bank.
Folders starting with a colour name will be loaded into that colour bank
Example "Blue - Frooty Loops" will load into the Blue bank
Sub-folders are ignored, only folders in the root directory are scanned for wav files
Works best with UHS Speed Class 3 cards with |3| symbol printed on the card

Specs:

Electrical and Mechanical Specifications:
Module Size:
16 HP Eurorack format module
10-pin Eurorack power header
1.3" (33mm) maximum depth with power cable
Power consumption:
+12V: 135mA
-12V: 41mA
+5V rail: not used
Connect red stripe of power cable towards the bottom of the module, which is marked with a white stripe and the words -12V and POWER
Audio Inputs:
20Hz to 10kHz (+/-0.1dB); -6dB rolloff @ 20kHz
21V peak-to-peak maximum before clipping
Audio Outputs:
0Hz (DC) to 22kHz with maximum -1.8dB difference between file data and output
+10.5V to -10.5V maximum output
Trigger inputs:
Latency: 0.7us typical

Included with the Sampler:
16GB micro SD card (class 10)
SD adaptor
10-to-16 pin power cable
M3 Knurlie screws

Notes: ***B-STOCK: Box opened, light surface marks, product in perfect working condition ***


Great value from 4ms's twist on the Stereo Triggered Sampler module, this time capable of playing and manipulating stereo or mono WAV files from an SD card.

Supplier's Notes:
The Sampler is a variation of the Stereo Triggered Sampler.

Record, play and loop stereo .wav files with an SD Card. Includes the same 2022 Sampler Pack from the Stereo Triggered Sampler.

Features:

The Sampler plays stereo or mono .wav files from an SD Card. Samples are arranged into banks by placing .wav files into folders (each folder is a bank). A maximum of 10 samples can be loaded in a bank. There is a maximum of 60 banks (600 samples maximum total).
Sample files are limited to 4GB each, which is over 6 hours at 44k/16b/stereo.

Hundreds of samples included on microSD card
Extremely quiet, low noise and low jitter design
Stereo or Mono output

A knob and CV jack selects the Sample to play, and the Start Position knob and CV jack control where in the sample playback will begin. The Length knob and CV jack determine how much of the sample is played back: from tiny grains, to percussive hits, to longer loops... or just the entire file.

Pressing Play or firing a trigger into the Play Trig jack will play the sample. Holding the Play button down for a second will toggle looping.

There's also a Reverse button and jack for backwards playback, and an End Out jack for synchronizing loops, or cascading sample playback with other events.

To record samples, hold Play and Reverse for two seconds. Press Play again or fire a trigger into the Play/Rec Trig jack to start and stop recording. Each recording will create a new stereo 48kHz 24bit .wav file in the current bank's folder. Recordings can be as long as your card has the capacity for: a 256GB card is 18 days of continuous recording (432.9 hours). Audio data is split into maximum 4GB wav files on the microSD card.

Play button/trigger jack: Tapping the button or receiving a trigger starts/re-starts the sample
Sample CV/knob: select which sample within the channel's bank
Pitch CV and Pitch knob: playback pitch (-10 to +4 octave range)
Start Pos CV/knob: position in the sample to begin playback (loop start point)
Length CV/knob: playback time (loop end point)
Length knob at max: entire file is played
Length knob 50%-99%: 200ms - 5s of the sample is played (beginning at the Start Position)
Length knob <50%: Percussive decay envelope is applied to the playback (attack-only envelope if playing Reverse)
Length <1%: Tiny grains are played (can be used to sweep through sample file data manually)
Reverse button/jack: toggles forward/backwards
Bank button: selects channel's bank
Reverse + Start Pos button/knob combo allows for setting volume of playback
Maximum file size for playback: 4GB per file (6.7 hours per file at 44.1kHz/16b/stereo)
microSD Card is hot-swappable when Busy light is off: no power-down required to change cards.
Samples that are pre-loaded into memory can continue playing while card is swapped.

File Organization:

Using a computer, the intuitive automatic bank loading features make dragging and dropping your entire sample library a snap. No files need to be renamed. Just create folders and put up to 10 samples in each. If you want a folder to be associated with a particular colour of the Bank button, name the folder a colour name (such as "Blue - Loops").

Ships with a high-speed 16GB microSD card, loaded with hundreds of samples created for 4ms, from musicians such as Richard Devine, Wobbly, Moor Mother, Robert Aiki Aubrey Lowe, Joseph Pailo, Russell E.L. Butler, Hugo Paris & Marc Kate, Paul Barker, Baseck, Animal Collective, Cristian Vogel, Jay E, Marcus Fischer, Chris Carter, Daedelus, Nero Bellum, Anna Sitko, Thomas Fang, Bogdan Raczynski, and more (Sample List)

Intuitive bank/colour organization system; no need to rename your wav files
Record new samples directly to a bank with the Record Input jacks...
... or drag your folders of sound files onto the microSD card, and each folder will become a bank.
Folders starting with a colour name will be loaded into that colour bank
Example "Blue - Frooty Loops" will load into the Blue bank
Sub-folders are ignored, only folders in the root directory are scanned for wav files
Works best with UHS Speed Class 3 cards with |3| symbol printed on the card

Specs:

Electrical and Mechanical Specifications:
Module Size:
16 HP Eurorack format module
10-pin Eurorack power header
1.3" (33mm) maximum depth with power cable
Power consumption:
+12V: 135mA
-12V: 41mA
+5V rail: not used
Connect red stripe of power cable towards the bottom of the module, which is marked with a white stripe and the words -12V and POWER
Audio Inputs:
20Hz to 10kHz (+/-0.1dB); -6dB rolloff @ 20kHz
21V peak-to-peak maximum before clipping
Audio Outputs:
0Hz (DC) to 22kHz with maximum -1.8dB difference between file data and output
+10.5V to -10.5V maximum output
Trigger inputs:
Latency: 0.7us typical

Included with the Sampler:
16GB micro SD card (class 10)
SD adaptor
10-to-16 pin power cable
M3 Knurlie screws

Notes: ***B-STOCK: Dent on the side, product in perfect working order***


The Shaped Dual EnvVCA is a two-channel analogue envelope generator with waveshapers and a stereo linear VCA. Unlike conventional analogue envelope modules, the waveform of each envelope can be controlled with a slider or CV without changing the envelope timing. With a wide time range from an hour to 2.5kHz, and a plethora of CV inputs and attenuverters, it can be used as an LFO, audio-rate oscillator, slew limiter, waveshaper, ASR/ADSR/complex EG, independent audio/CV VCA, envelope follower, sidechain processor, and general utility module. Each channel has dedicated linear outputs plus attenuverters and offset controls for the variable waveshape outputs, making it an ideal modulation source and stereo VCA.

100% analogue

Shaped Dual EnvVCA

20HP Eurorack format module
0.95" (24mm) maximum depth (includes power cable)
10-pin Eurorack power header

Power consumption
+12V: 255mA
-12V: 230mA

Audio/VCA
100k input impedance, 1k output impedance, DC-coupled
VCA gain range: -90dB to +2.0dB, linear response to CV from 0V to 5V
VCA unity gain: 4.4V CV
DC to 20kHz, +/-0.1dB

Envelope Times
Minimum rise or fall time: ~200us per segment (2.5kHz max frequency)
Maximum rise time: >20 minutes (typically > 40 minutes)
Maximum fall time: >12 minutes (typically > 20 minutes)

Jacks:
Env jack: Min = -10.2V, Max = +10.1V, maximum amplitude 9.3Vpp
Trigger jack: rising edge threshold = 1.25V
Follow jack: active range = 0V to +5V

EO* jacks:
EOR (channel A): <80mV low to >4.50V high gate output
EOF (channel B): <80mV low to >4.95V high gate output
Minimum stable pulse width: 1ms. Shorter than this may produce extra 50us pulses
Audio In/Out jacks: -10V to +10V maximum range without clipping

Notes: A fresh twist on a simple 303-style acid synth, featuring a triangle/sawtooth/square wave VCO, multi-mode resonant filter, simple AD envelope and a VCA which can be overdriven. Excellent value.

Supplier's Notes:
ADDAC started this module with the idea of developing a complex drum source however, somewhere along the process, it was clear how much better it performed as a synth voice and this lucky accident was embraced.

It features a VCO with a [FREQUENCY] and [FINE TUNE] knob plus a dedicated CV Input and Attenuator knob (tunable over 4 octaves).

The VCO waveform output is achieved by selecting either a Triangle or Saw through a switch. the selected waveform can then be mixed/balanced against the square wave. The resulting mix is then sent to the Filter.

The Filter features a [CUTOFF] and [RESO] resonance knob plus a Cutoff CV Input and Attenuverter knob.

A 3 position switch is used to select the filter type: Highpass, Bandpass or Lowpass.

The resulting output is then sent to the VCA.

The VCA features an Input with [INPUT GAIN] knob which at maximum can amplify the incoming signal by a factor of 2.

This is a very important control, it accepts any signal Trigger, Gate or CV. Whatever input is plugged in the signal is then fed through an AD with a very short attack and controllable decay through the [VCA DECAY] knob plus the CV Input and Attenuverter knob. The resulting slewed signal is then used to control the VCA gain.

This signal is also sent to the CV OUTPUT as well as the LED monitor.

The Accent input adds to the Input signal creating a different amplitude output.


The CV OUTPUT is normalled to the Frequency and Cutoff inputs.

Tech Specs:
9HP
4cm deep
80mA +12V
80mA -12V

The [INPUT GAIN] knob

Usually Attack/Decay envelopes have a maximum voltage of +5v, no matter if the input gate is +5v or above the AD will clip at +5v. In this case, this clipping method was not used, and instead ADDAC allowed the incoming voltage to determine the maximum AD voltage, meaning that if a +5v gate is present then the AD maximum voltage will be +5v but if a gate of +10v is sent then the AD maximum voltage will be +10v.
This also means that with higher input voltages the decay, although falling at the same speed, will be longer than with lower voltages as it has a longer range to go back to 0v.

As previously mentioned, The [INPUT GAIN] knob can amplify the incoming input by a factor of 2, allowing to use a standard +5v gate or envelope and being able to make the resultant AD go up to +10v.

The AD signal is responsible for opening the VCA. Up to +5v the VCA will open to unity gain above this value the VCA will start to amplify and eventually saturate and distort. This saturation will add harmonics to the signal which will change its gentle timbrical nature to a more unique and peculiar timbre that will make the module shine in Acid contexts.

Adding high levels of Resonance or even filter self oscillation in combination with high VCA saturation will create even more harmonics that ADDAC highly encourage the user to explore.

Notes: Six segment generator. Looping or one shot envelope generator. Chainable, so it can be expanded to link multiple units.

An exact hardware replica of the Mutable Instruments Stages.

Dimensions
14 HP
25 mm deep

Current Draw
80 mA +12V
20 mA -12V
0 mA 5V

Notes: ***B-STOCK: Item refurbished, repaired and in perfect working order.***


Six segment generator. Looping or one shot envelope generator. Chainable, so it can be expanded to link multiple units.

An exact hardware replica of the Mutable Instruments Stages.

Dimensions
14 HP
25 mm deep

Current Draw
80 mA +12V
20 mA -12V
0 mA 5V

Notes: Pan and cross fade up to three signals with AJH's versatile Triple Cross. Four different modes allow you to set up the three channels in numerous ways, for both audio and CV processing.

Supplier's Notes:
The Tone Science Triple Cross module is a design collaboration between electronic musician/composer Ian Boddy and AJH Synth.

It features three independant cross fader and panner channels, and it can be used with both audio and CV signals. Each of the channels can be configured in one of four different ways:

1) One In, One out Linear VCA

2) Two in, One out crossfader

3) One in, Two out panner,

4) Two in, Two out cross fader & reversing panner combined.

Audio rate modulation can also be used on the CV inputs to create Ring modulation and Cross modulation type sounds. Each channel has a dedicated Fade control, CV input, and CV Level attenuverter. These can be used together to bias incoming CV signals.

The L1 and L2 outputs from channels 1 and 2 are normalised to channel 3's inputs, which also have their own level controls to balance incoming signals. This allows very interesting, complex fading and panning between four different input sources, to either Mono or Stereo outputs..

The Triple Cross is very versatile, yet relatively simple to understand and use. However, as they say "knowledge is power", so do spend a little time reading about how to configure the channels in the four different modes, and how to combine all three channels together to create a super-powerful Four to Two to One cross fader.
Each of the three channels can be configured in four different ways, and all three can be used simultaneously. They do not all have to be in the same mode, so we could for example use channel 1 as a cross fader, channel 2 as a Panner for completely different signals, and channel 3 as a Linear VCA, again for different signals.

Specifications

Effective CV Range for CV-1, CV-2 and CV-3 is 0 to +5V with attenuverter fully clockwise or 0 to -5V with attenuverter fully anticlockwise.
Maximum permissible CV Range for CV-1, CV-2 and CV-3 is -12 to +12V
IN 1A to IN 3B Input levels -5V to +5V, levels up to +/-10V are possible however some clipping may occur.
Module Width: 14hp
Module Depth: 26mm (Including power lead)
Current Usage: 80mA Positive, 72mA Negative

Notes: ***B-STOCK: Box opened, but product is in excellent condition and in perfect working order***


Pan and cross fade up to three signals with AJH's versatile Triple Cross. Four different modes allow you to set up the three channels in numerous ways, for both audio and CV processing.

Supplier's Notes:
The Tone Science Triple Cross module is a design collaboration between electronic musician/composer Ian Boddy and AJH Synth.

It features three independant cross fader and panner channels, and it can be used with both audio and CV signals. Each of the channels can be configured in one of four different ways:

1) One In, One out Linear VCA

2) Two in, One out crossfader

3) One in, Two out panner,

4) Two in, Two out cross fader & reversing panner combined.

Audio rate modulation can also be used on the CV inputs to create Ring modulation and Cross modulation type sounds. Each channel has a dedicated Fade control, CV input, and CV Level attenuverter. These can be used together to bias incoming CV signals.

The L1 and L2 outputs from channels 1 and 2 are normalised to channel 3's inputs, which also have their own level controls to balance incoming signals. This allows very interesting, complex fading and panning between four different input sources, to either Mono or Stereo outputs..

The Triple Cross is very versatile, yet relatively simple to understand and use. However, as they say "knowledge is power", so do spend a little time reading about how to configure the channels in the four different modes, and how to combine all three channels together to create a super-powerful Four to Two to One cross fader.
Each of the three channels can be configured in four different ways, and all three can be used simultaneously. They do not all have to be in the same mode, so we could for example use channel 1 as a cross fader, channel 2 as a Panner for completely different signals, and channel 3 as a Linear VCA, again for different signals.

Specifications

Effective CV Range for CV-1, CV-2 and CV-3 is 0 to +5V with attenuverter fully clockwise or 0 to -5V with attenuverter fully anticlockwise.
Maximum permissible CV Range for CV-1, CV-2 and CV-3 is -12 to +12V
IN 1A to IN 3B Input levels -5V to +5V, levels up to +/-10V are possible however some clipping may occur.
Module Width: 14hp
Module Depth: 26mm (Including power lead)
Current Usage: 80mA Positive, 72mA Negative

Notes: The Tone Science Triple Cross module is a design collaboration between electronic musician/composer Ian Boddy and AJH Synth.

It features three independant cross fader and panner channels, and it can be used with both audio and CV signals. Each of the channels can be configured in one of four different ways:

1) One In, One out Linear VCA

2) Two in, One out crossfader

3) One in, Two out panner,

4) Two in, Two out cross fader & reversing panner combined.

Audio rate modulation can also be used on the CV inputs to create Ring modulation and Cross modulation type sounds. Each channel has a dedicated Fade control, CV input, and CV Level attenuverter. These can be used together to bias incoming CV signals.

The L1 and L2 outputs from channels 1 and 2 are normalised to channel 3's inputs, which also have their own level controls to balance incoming signals. This allows very interesting, complex fading and panning between four different input sources, to either Mono or Stereo outputs..

The Triple Cross is very versatile, yet relatively simple to understand and use. However, as they say "knowledge is power", so do spend a little time reading about how to configure the channels in the four different modes, and how to combine all three channels together to create a super-powerful Four to Two to One cross fader.
Each of the three channels can be configured in four different ways, and all three can be used simultaneously. They do not all have to be in the same mode, so we could for example use channel 1 as a cross fader, channel 2 as a Panner for completely different signals, and channel 3 as a Linear VCA, again for different signals.

Specifications

Effective CV Range for CV-1, CV-2 and CV-3 is 0 to +5V with attenuverter fully clockwise or 0 to -5V with attenuverter fully anticlockwise.
Maximum permissible CV Range for CV-1, CV-2 and CV-3 is -12 to +12V
IN 1A to IN 3B Input levels -5V to +5V, levels up to +/-10V are possible however some clipping may occur.
Module Width: 14hp
Module Depth: 26mm (Including power lead)
Current Usage: 80mA Positive, 72mA Negative

Notes: ***B-STOCK: Product has light surface marks/scratches, but otherwise in perfect working condition***


The 'Quaid Megaslope' is a five stage function generator or modulator which operates in one of 3 modes; a multistage 'CZ' or 'Juno' style complex envelope, a super flexible LFO and a step sequencer with per step programmable slew or slides.

Each mode produces a varying output voltage moving from point to point across a set number of chained together stages. Each stage features a destination level, an overall rate or time to reach its destination level and a variable slope for the output path to take. As well as direct control, every stage feature voltage control of both level and rate. There are both unipolar and bipolar voltage outputs together with triggers emitted for the end of each stage and the end of a full cycle.

The Quaid Megaslope is designed to be fun, flexible and intuitive to use.

Notes: ALM's first analogue oscillator is a typically smart design, featuring thru-zero FM, continuously morphing wave shapes, dual subs and voltage-controlled FM index.

Supplier's Notes:
The 'TAZM-O' is an analogue triangle core oscillator featuring through-zero frequency modulation and a collection of some of ALM's favourite features of classic oscillator designs.

It includes a continuous morphing wave/pulse width shape control inspired by the Serge NTO, dual SH-101 style varied pulse sub octave outputs, a voltage controlled FM Index typically found in larger complex oscillators, a built in output level VCA and voltage controlled octave transposition similar to the multipliers found on Akemie's Castle digital FM VCO.

Designed to act as the primary oscillator in your system the 'TAZM-O' offers a wide range of timbral and patch flexibility within a relatively compact 12HP size, making it the perfect fit for any modular system.

Continuous crossfading wave shape with direct and voltage control.
Through-zero FM input with direct and voltage controlled mod index.
Dedicated outputs for sine (or triangle), saw and square sub-1 & sub-2.
Primary output with level VCA.
V/Oct input with approx 8 octave range.
Octave transpose CV input ranging 3 octaves.
Hard Sync input.
LFO mode with bipoler LED indication.
Rear switches for selecting Sub-2 pulse width, and sine/triangle waves.
Skiff friendly with reverse power polarity protection.
Made in England.

Dimensions
12 HP
38 mm deep

Current Draw
70 mA +12V
60 mA -12V

Notes: ***B-STOCK: Box opened, but product is in excellent condition and in perfect working order***


ALM's first analogue oscillator is a typically smart design, featuring thru-zero FM, continuously morphing wave shapes, dual subs and voltage-controlled FM index.

Supplier's Notes:
The 'TAZM-O' is an analogue triangle core oscillator featuring through-zero frequency modulation and a collection of some of ALM's favourite features of classic oscillator designs.

It includes a continuous morphing wave/pulse width shape control inspired by the Serge NTO, dual SH-101 style varied pulse sub octave outputs, a voltage controlled FM Index typically found in larger complex oscillators, a built in output level VCA and voltage controlled octave transposition similar to the multipliers found on Akemie's Castle digital FM VCO.

Designed to act as the primary oscillator in your system the 'TAZM-O' offers a wide range of timbral and patch flexibility within a relatively compact 12HP size, making it the perfect fit for any modular system.

Continuous crossfading wave shape with direct and voltage control.
Through-zero FM input with direct and voltage controlled mod index.
Dedicated outputs for sine (or triangle), saw and square sub-1 & sub-2.
Primary output with level VCA.
V/Oct input with approx 8 octave range.
Octave transpose CV input ranging 3 octaves.
Hard Sync input.
LFO mode with bipoler LED indication.
Rear switches for selecting Sub-2 pulse width, and sine/triangle waves.
Skiff friendly with reverse power polarity protection.
Made in England.

Dimensions
12 HP
38 mm deep

Current Draw
70 mA +12V
60 mA -12V

Notes: For the creation of a sound it is absolutely a necessity to have an envelope generator. Moreover, in most cases you need to use two of it, one for the VCF, and another one for the VCA, or for other moulations perhaps.

With this in mind, the DUAL ENV came into existence, with an extra feature of the GATE DELAY function. Using the own dedicated potentiometer of this function you can make the second envelope to delay.

Both of these envelope generators can be set-up for GATED or TRIGGERED mode. This way you can turn on/off the legato playing. With separate switches you can set the curves of the envelopes by choosing linear or exponential.

For the sake of easy and convenient adjustment, AS divided the time potentiometers into two sections. This way you can set the time from completely turned down position to mid position 2ms to 1s, and from mid position to completely turned up position 1s to 10s. At the delay knob its 0s, 200ms, 2s. Using this method you can really fine tune the times.

Just in case, if this wasn't enough yet, you can find the inverse of the envelope signs on the outputs of the DUAL ENV. It means the positive output works from 0V to +10V, the inverse output works from 0V, to -10V. Moreover, the second envelope has an OFFSET switch, so you can shift the output level. This way it can be 0V to 10V, or -5V to +5V

All of these features make it possible to create more and more exciting modulations and the output of the second envelope becomes compatible with modulation inputs receiving -/+5V control voltage.

Technical Specifications
Type: Transient Generator
Module depth: 33mm
Module width: 16HP (80.4mm)
Module weight: 215g
Connector type: 10P IDC Eurorack
Power consumption: +90mA / -10mA
Gate, Trig inputs x4: 0V / 5V
ENV outputs x4: -10V / 0V, -5V / +5V, 0V / +10V

Notes: Lowpass VCF & VCA

The heart and soul of all synthesizers is the filter. And the most important one is the low-pass filter. And the Lowpass VCF & VCA is a modern, linear, 100% analogue filter. It works perfectly in any circumstances, and reacts "musically" within the most extreme set-ups as well.

It's very important to make the filter capable of receiving multiple audio signals, since the creation of a timbre often requires a few oscillators, noise generators, external sources perhaps. For this reason, AS built into the module a three channel mixer, and you can find here the post-filter VCA as well.

All the same applies on the reception of the CV signs. Besides the V/OCT input, there are two more adjustable CV inputs for the frequency modulation, and separate input for controlling the resonance, and one for the VCA level.

The filter reacts "musically". For example: if you turn up the resonance knob, you'll hear a soft sinus resonance. The sound won't fall apart, the filter won't start to "scream". Besides of all, a Resonance Boost circuit was built into the filter, which makes sure that lifting the resonance won't let fade the range of deeper frequency.

And guess what! You can overload the filter! Give it a try, you'll hear a very pleasant drive effect. This effect is based on the attribute of the filter's own circuit, not by a built-in distortion.

For the sake of comfortable application, the input of the Freq CV2 can be assigned to the VCA CV input by using its own switch. In this case the same generator is capable of modulating the frequency of the filter, and the amplitude of the VCA as well.

Technical Specifications

Type: Resonant Filter & Amplifier
Module depth: 33mm
Module width: 16HP (80.4mm)
Module weight: 215g
Connector type: 10P IDC Eurorack
Power consumption: +60mA / -50mA
CV Inputs x5: -5V / +5V, 0V / +10V
Audio Inputs x3: 10Vpp
Audio Outputs x2: 10Vpp

Notes: VCO

Turn it on and play! No need to wait for the VCO to get warm.

First of all, AS Synthesisers emphasised the tunability of the oscillator. In so many cases it's necessary to tune the oscillator back and forth in the middle of a performance. And many cases it's really hard to hit the proper pitch, that's why AS decided to use -/+1 octave tune potentiometer (marked with a piano keyboard). You can switch octaves in four steps as well, and for highly precise tuning there's a fine tune knob too.

This 100% analogue and temperature compensated oscillator, generates square, saw, triangle and sine waves. Besides the individual waveform outputs, there's a selectable waveform output as well.

The waveforms appear with the same phase and the same amplitude (10Vpp) on the outputs. This makes it possible to use multiple waveforms simultaneously from the same VCO, without phase quench or volume fluctuation.

The pulse width can be adjusted between 10% and 90%. There's a controllable PWM CV input too. The SAW compatible HARD SYNC input can be turned on/off.

Besides the V/OCT input, there are two adjustable exponential CV inputs available for the modulation of the frequency. The whole range of frequency of the VCO is in between 16.352Hz and 8.372kHz (C0 - C9), so it means 10 octaves with +/-5 cents accuracy.

Technical Specifications

Type: Audio Range Oscillator
Module depth: 33mm
Module width: 16HP (80.4mm)
Module weight: 210g
Connector type: 10P IDC Eurorack
Power consumption: +60mA / -40mA
CV inputs x5: -5V / +5V, 0V / +10V
Waveform outputs x5: 10Vpp

Notes: Atomosynth's legendary drum synthesizer comes back this time with four independent, all-analogue percussion synth voices.

Two of them feature a full percussion synth with triangle and square wave oscillator, an envelope for the "sweep" effect, one modulator with triangle and square wave as well as noise, also a decay envelope for the overall volume contour.
These are very flexible generating from powerful bass drums, toms, clicks, all the way to "laser gun" and weird glitch sounds.

The other two voices feature an oscillator with "metal" and square wave, a white noise generator, a mixer, and also a decay envelope. These are great to produce metallic sounds like hi-hats, crashes, cymbals, clicks, beeps, and all craziness in between.

Combining the two synth voice types you can expand the possibilities even further for more complex sounds. Finally an output mixer with individual level controls and outputs for each voice and a master output.

The new Tottem produces a "raw" organic character sound, that does not emulate any drum machine and stands apart from the very polished and over-processed digital drum synthesizers and samplers, giving you a new sound to enrich your percussion palette.

Specs

Four analogue percussion synthesizer voices.
Two voices feature, one oscillator, two decay envelopes, one LFO, and a noise generator.
Two voices feature, one square wave and metal oscillator, one noise generator, one mixer, and a decay envelope.
Individual manual gate buttons.
Output mixer.
Individual outputs for each voice.

Dimensions
24 HP
25 mm deep

Current Draw
197 mA +12V
75 mA -12V

Notes: Mid Thing v2 is a flexible MIDI to CV converter. Allowing polyphonic notes handling, envelope and LFO generation as well as all available MIDI messages to be converted into CV.

This is a huge upgrade from the previous beloved MIDI Thing, which adds a screen for easy configuration, 12 assignable ports, TRS, USB Host and Device, MIDI merge OUT, a web configuration tool, and a VCV rack bridge counterpart.

Features

12 Configurable ports
TRS type A MIDI IN and OUT, USB host and device connectivity.
Configuration screen with intuitive menu diving.
Web configuration tool.

Specifications

Current Draw: +12V: 150mA, -12V: 5mA
Width: 6HP
Deepth: 30mm including power connector
Aluminium, heat-treated front panel.
Designed, kits prepared and assembled in Barcelona.

Notes: Really clever stuff here. The Octaves VCO takes an additive approach, layering harmonics on top of a fundamental frequency to create complex tones. Control the six bands via CV to adjust the harmonic content.

Supplier's Notes:
A harsh and funky take of an additive Oscillator.

Pile up multiplications of your frequency to get a lo-fi-retro wall of squared sound!

You get six doubled frequency pulses, or octaves, with common PWM and volume control for each of them.

The output of each is cascaded to the next one, so you can either have one output with all frequencies or break the chain and get several sums and modulate each independently!

Features
Six bands, multiple of the base frequency.
Square wave oscillator with Octaves selector PWM control and sync.
Range control for Tune pot.
Volume CV control and individual output for each band
Cascaded summing outputs.

Specifications
Current needs: +12V: 110mA, -12V: 84mA
Width: 12 HP
Depth: 22mm (assembled and DIY), including power connector
Aluminium, heat-treated front panel
Designed, kits prepared and completed modules assembled in Barcelona

Notes: A breakout module for the Trolley Bus power system, the On/Off includes a DC input, power switch, two USB charging sockets and four LEDs to confirm the different voltage outputs are working.

Supplier's notes:
Trolley Bus

Ready to feed the most modern and power-hungry modules.

A 5A power solution, 28 slots powered by four high-quality DC-DC converters.

ON/OFF 4HP - 3U module with 2 USB-A charging ports and a Power Button.

Friendly Plug and Play, tools are not required.

Features
25 mm height over regulators grid and 15 mm height on the rest of the bus
Horizontal connectors to maximize space
2,5mm barrel power connector
On/Off 4HP module
2 USB-A charging ports

Specs
Power brick: 135W 2.5mm Barrel connector center positive (included)
Current: +12V: 5A, -12V: 2,5A, 5V: 4A
Measurements: 423 mm x 80mm
Designed, kits prepared and completed modules assembled in Barcelona

Notes: The Sensory Coupler allows you to easily convert touch, proximity, light, magnetic fields, motion, and more into CV and gate.

Built-in touch contact and 1/8" TRS jack sensor interface. Other sensors and devices like expression pedals can be easily added. DIY info coming soon.

Calibration mode. Sensors produce different readings in different environments, the Sensory Coupler calibrates them to utilize the entire 0-10V CV output range.
CV output based on calibrated or raw sensor data. 0-10V.
Two gate outputs. Work based on an adjustable threshold level. When the sensor reading is above or inside the threshold, GATE will output 12V while !GATE will be 0V and vice versa.
Smoothing modes. Sensor readings can be chaotic when you might not want them to be so there are two smoothing modes. One simply averages readings to create slow rises and falls while the other acts like an envelope follower with adjustable decay.
Large LED strip display. Visualizes the sensor reading, threshold, smoothing mode and more.

USB MIDI standalone mode. The Sensory Coupler can work without modular +-12V power, getting power with the built in USB-C connector and sending and receiving MIDI notes and CC. In USB mode gate outputs work at 4V instead of 12V but CV out is disabled.

Includes:

Phototransistor / light sensor
Hall effect / magnetic sensor
Accelerometer / motion sensor
Gooseneck 1/8" TRS cable. Easy to bend and stays in place.
2M 1/8" TRS cable. Has a higher gauge than a regular 1/8" modular cable, allowing for sensors to be connected at a distance without introducing noise.
50mm long alligator clip wire for touch sensor
Donut magnet
6 hp, 32mm deep
+12V 150mA
5V 0mA
-12V 12 mA

Notes: ***B-STOCK: Box opened, product in perfect working order***


High-quality audio mixing in Eurorack format. Five mono input channels, each with direct outs, pan controls, aux sends, adjustable gain and clickless muting. Versatile and effective.

Supplier's Notes:
D.O.MIXX was created based on a couple of simple desires - to not only have a quality in-the-rack mixer as the last thing in the modular signal chain, but to also have an easy means to grab a Direct Output from each channel, so more detailed mixing can take place in a DAW after the fact. These Direct Outs can also be used to route the channel wherever you'd like back into the modular system - a single-channel buffered mult if you will. Beyond that, there are other standard mixer features such as an Aux Bus (with Pre/Post send switch), stereo panning, and click-less muting on each channel. All level knobs range from 8 to +6 dB of gain.

Direct Outputs are post-gain/mute.

Note this mixer is AC-coupled, and as such is only suitable for audio signals, not CV.

170 mA +12V
170 mA -12V
0 mA 5V

Width: 22HP

Depth: 3.3 cm

Power: 170 mA @ 12V, 170 mA @ -12V

Input / Aux Send Gain: 8 to +6 dB

Output Gain: 8 to +6 dB

Inputs/Outputs: All I/O is unbalanced

THD + Noise: 0.005%; 1 kHz @+15 dBu with 0 dB gain

Dynamic Range: >107 dB, A-weighted

Input Impedance: 100K ohms

Output Impedance: 300 ohms

Notes: What does this do?

This is a mini analogue synthesizer that produces snare drum sounds. Inspiration was taken from the 5U Cor Synth DR02 module. Only the flow chart was studied and used to create this BLM product. VCV Rack was also used to simulate and test the building blocks.

Most of the circuits contained in this product are from other blue lantern module designs.

Some of the building blocks:

-2 1V/Octave Triangle Core VCO's
-2 Sine Wave Shapers
-4 Envelope Generator
-White Noise Generator
-High Pass Filter
-Tone Filter
-2 VCA's
-Mixer

The goal of this module was to recreate some of the more exotic electronic snare sounds.

You're not getting another Roland 'TR' module with the Gimme Some Snare Drum. All the building blocks contain full analogue circuitry, like OTA chips, and Op-amps. No vintage transistor based (Bridge T Oscillator) circuits are used in this product.

The best description as to what the kind of snare drum sounds this module can produce is something comparable to:

an Electribe Korg ER-1, Simmons Snare Drum, and the Mattel Synsonics.

Dimensions
16 HP
32 mm deep

Current Draw
107 mA +12V
97 mA -12V

Notes: A really clever take on looping, falling somewhere closer to granular synthesis depending on how you use it. Layer and repeat multiple sound sources to create textures, chords and unique timbres.

Supplier's Notes:
Endless Processor is a dual-channel infinite sound sustainer machine.

Put your favourite instruments, unique timbres, or field recordings - virtually any sound - and make it last forever.

It is not a looper in the usual sense - Endless Processor resynthesizes your sounds to create a perfect clickless stream while preserving the timbral and tonal character of the original.

Endless Processor always listens to audio input and keeps a most recent history. Experiment with sustaining little bits of a sample or make a massive wall of sound with the ability to select how much memorized audio to process.

Stack your sounds to create harmonies, textures, or drones with 5 layers per channel. Each layer can be re-processed or cleared while keeping other ones in place. Set fade-in and fade-out time to quickly or gradually introduce a new layer or remove the existing one.

Additional controls will help you to adjust or shape a channel volume (think built-in VCA).

Dimensions
16 HP
25 mm deep

Current Draw
125 mA +12V
10 mA -12V

Notes: ***B-STOCK: Box opened, but product is in excellent condition and in perfect working order***


Endless Processor is a dual-channel infinite sound sustainer machine.

Put your favourite instruments, unique timbres, or field recordings - virtually any sound - and make it last forever.

It is not a looper in the usual sense - Endless Processor resynthesizes your sounds to create a perfect clickless stream while preserving the timbral and tonal character of the original.

Endless Processor always listens to audio input and keeps a most recent history. Experiment with sustaining little bits of a sample or make a massive wall of sound with the ability to select how much memorized audio to process.

Stack your sounds to create harmonies, textures, or drones with 5 layers per channel. Each layer can be re-processed or cleared while keeping other ones in place. Set fade-in and fade-out time to quickly or gradually introduce a new layer or remove the existing one.

Additional controls will help you to adjust or shape a channel volume (think built-in VCA).

Dimensions
16 HP
25 mm deep

Current Draw
125 mA +12V
10 mA -12V

Notes: Introducing SUM0, a voltage-controlled oscillator with expanded harmonic possibilities, in a Eurorack format.

The 4 classic waveforms are generated by a meticulously designed oscillation engine.

You can modulate its frequency and its pulse width thanks to its integrated LFO, capable of reaching audible frequencies to achieve expressive modulations with the simple touch of a switch.

Expand the voice of your system by creating complex waveforms and high harmonic content thanks to its output mixer. This mixer also has an input to integrate an external signal to the mix output.

Of course, all its parameters (FM, PWM, SYNC, V/OCT) are at your fingertips through its patch points on the front panel.

And of course, assembled with a load of passion in Bocuma's studio-workshop in Guadalajara.

Nerdy-specs:

22HP
+12V > 12mA -12V > 12mA

Notes: ***B-STOCK: Box opened, but product is in excellent condition and in perfect working order***


Introducing SUM0, a voltage-controlled oscillator with expanded harmonic possibilities, in a Eurorack format.

The 4 classic waveforms are generated by a meticulously designed oscillation engine.

You can modulate its frequency and its pulse width thanks to its integrated LFO, capable of reaching audible frequencies to achieve expressive modulations with the simple touch of a switch.

Expand the voice of your system by creating complex waveforms and high harmonic content thanks to its output mixer. This mixer also has an input to integrate an external signal to the mix output.

Of course, all its parameters (FM, PWM, SYNC, V/OCT) are at your fingertips through its patch points on the front panel.

And of course, assembled with a load of passion in Bocuma's studio-workshop in Guadalajara.

Nerdy-specs:

22HP
+12V > 12mA -12V > 12mA

Notes: A characteristically unique take on mixing from Buchla, with six mono inputs and a built-in mic/guitar pre-amp. Each channel can be cued to a monitor mix, while the first and last channels also include voltage-controlled panning.

Supplier's Notes:
The Tiptop 207t is a modern reimagining of the classic Don Buchla 207 Mixer/Preamplifier from the 1970s 200 Series. This stereo mixer comes with a built-in preamp that allows you to boost external instruments and microphones, making it a versatile tool for any modular setup. The 207t also features a six-channel mixer with a variety of signal routing options, including the ability to route channels to the monitor and L&R signal outputs, with per-channel control over loudness and panning.

Each channel has a Mon switch that sends the channel's signal to the monitor outputs, which are always full-volume and summed to mono, making it useful for basic monitoring applications or rudimentary mixing. The Prog switch sends the signal to the L&R signal outputs, with loudness controlled by the Level Adjustment slider and panning determined by the Channel Assignment knobs. The first and sixth channels offer voltage control of panning; these channels are hard-panned when no CV is applied.

The preamp section features a 1/4" input and multiple gain settings, making it suitable for use with external line level instruments, electric guitars, or dynamic microphones. The continuous amplification control provides added flexibility for your audio needs. Finally, the Expansion In is a stereo input that sums to the left and right main outputs, which is great for chaining multiple 207t modules or adding another stereo source at the final output.

While the 207t's functionality may be simple, it is an essential part of any 200t system, serving as the glue that holds everything together. The Tiptop 207t is a fantastic mixer/preamp option that delivers quality sound and reliable performance.

Buchla 207t Features

Mixer/preamp module based on Don Buchla's original 207 design
Six-channel mixer with per-channel level control and panning
Voltage-controllable panning on channels 1 and 6
Manual panning on channels 2-4
Program switches can act as channel mutes for main outputs
Mon switches route signal (in mono) to Monitor output
Expansion input useful for stereo chaining and more
Re-designed preamp for high audio fidelity
Preamp suitable for use with external instruments, electric guitars, dynamic microphones, and more

Eurorack module
28hp wide

Notes: ***B-STOCK: Box opened, but product is in excellent condition and in perfect working order***


A characteristically unique take on mixing from Buchla, with six mono inputs and a built-in mic/guitar pre-amp. Each channel can be cued to a monitor mix, while the first and last channels also include voltage-controlled panning.

Supplier's Notes:
The Tiptop 207t is a modern reimagining of the classic Don Buchla 207 Mixer/Preamplifier from the 1970s 200 Series. This stereo mixer comes with a built-in preamp that allows you to boost external instruments and microphones, making it a versatile tool for any modular setup. The 207t also features a six-channel mixer with a variety of signal routing options, including the ability to route channels to the monitor and L&R signal outputs, with per-channel control over loudness and panning.

Each channel has a Mon switch that sends the channel's signal to the monitor outputs, which are always full-volume and summed to mono, making it useful for basic monitoring applications or rudimentary mixing. The Prog switch sends the signal to the L&R signal outputs, with loudness controlled by the Level Adjustment slider and panning determined by the Channel Assignment knobs. The first and sixth channels offer voltage control of panning; these channels are hard-panned when no CV is applied.

The preamp section features a 1/4" input and multiple gain settings, making it suitable for use with external line level instruments, electric guitars, or dynamic microphones. The continuous amplification control provides added flexibility for your audio needs. Finally, the Expansion In is a stereo input that sums to the left and right main outputs, which is great for chaining multiple 207t modules or adding another stereo source at the final output.

While the 207t's functionality may be simple, it is an essential part of any 200t system, serving as the glue that holds everything together. The Tiptop 207t is a fantastic mixer/preamp option that delivers quality sound and reliable performance.

Buchla 207t Features

Mixer/preamp module based on Don Buchla's original 207 design
Six-channel mixer with per-channel level control and panning
Voltage-controllable panning on channels 1 and 6
Manual panning on channels 2-4
Program switches can act as channel mutes for main outputs
Mon switches route signal (in mono) to Monitor output
Expansion input useful for stereo chaining and more
Re-designed preamp for high audio fidelity
Preamp suitable for use with external instruments, electric guitars, dynamic microphones, and more

Eurorack module
28hp wide

Notes: The Cali oscillator is a new and improved version of the classic Buchla 258 wave shaping oscillator with an additional pulse width modulated output. The oscillator features the classic Sine to Square and Sine to Saw wave shaping with dedicated CV control. The Cali Oscillator differs from previous versions of the 258 in that it has a 3-way position switch rather than 2-way. This new middle position features a bonus waveform that will shape from a pulse into a kind of triangular trapezoid shape. The shaping control is more unpredictable in this middle position and the switch reacts to body contact when the wave shape is set low - it can be thought of as an extra bonus waveform, great for producing glitchy sounds! There are dedicated inputs for linear and exponential FM and the Cali also adds a Pulse output with it's own width control and PWM CV input. The behaviour of the pulse output can be affected by the position of the waveform switch and wave shape control. The module features Coarse and Fine frequency controls and an LFO mode, LFO range is accessed via an LED pushbutton that also acts as the LFO speed indicator - the button will light up when the waveform moves through its positive cycle. Because the wave shape modulation is independent of pitch this oscillator is very useful for creating complex timbres whilst retaining musical pitch.

Features

Sine to saw/square waveform output with cv over wave shaping

Pulse output with voltage controlled PWM

Linear FM with attenuator

Logarithmic FM with attenuator

Bonus 'trapezoid' output

Coarse & fine controls with LFO mode

Includes power supply isolation on frequency controls


Width: 12 HP
Depth: 22mm

Power
+12V = 37mA
-12V = 34mA

Notes: Gorgeous vintage-style through-zero FM here, featuring five simultaneous waveform outputs, pulse width modulation, soft sync and a dedicated LFO mode.

Supplier's notes:
The EN129 Thru Zero Oscillator is an all analogue triangle-core VCO specialising in frequency modulation. Analogue through-zero FM modulation produces a wide array of timbres particularly useful for bell like or percussive sounds. Through zero linear frequency modulation can be precisely dialled in thanks to a dedicated CV input attenuator and through zero offset control. Logarithmic FM is also available via it's own dedicated input with attenuator and both FM inputs have an LED to indicate incoming voltages. Simultaneous analogue wave outputs include: Sine, Triangle, Sawtooth, Square and Pulse wave with Pulse Width Modulation. The PWM control goes to zero at either end of it's range, which is very useful for creating rhythmic sounds with voltage control. Furthermore the PWM control doubles up as wave shape modulation for the Sawtooth wave - gradually altering the waveform until it shifts half a cycle. The EN129 features Coarse and Fine frequency controls as well as an LFO mode. LFO range is accessed via an LED pushbutton that also acts as the LFO speed indicator - the button will light up when the waveform moves through its positive cycle. A new addition of a Soft Sync Input allows the phase of the oscillator to be controlled by an external oscillator for an even greater range of timbres.

The EN129 is based on the pioneering work by Douglas Kraul and Bernie Hutchins. You can read the original Electronotes article from 1981 that the design is based upon here.

Features:

Soft Sync Input
Thru Zero Linear FM
Logarithmic FM
Zero to Zero PWM
Sawtooth Wave Shape Modulation
Simultaneous Outputs for: Sine, Triangle, Saw, Pulse & Square
Coarse & Fine Controls with LFO Mode
Includes Power Supply Isolation on Frequency Controls
Power consumption: 51mA at +12V and 47mA at -12V

Depth: 22mm

HP : 12

Notes: The Looping VC-ADSR is a 4-stage, loop-able, envelope generator based on the ENVGEN 8C IC from Electric Druid. The individual sections of the Envelope (Attack, Decay, Sustain, Release, Level and Time) can all be individually controlled via CV.

The module has 5 MODES of operation that can be selected via the pushbutton LED switch with the status indicated by the five LEDs above:

Normal Envelope - Gate signal at the GATE/TRIG input, fires the ADSR.
Trigger Mode - Trigger signal at the GATE/TRIG input fires the AD portion of the envelope. The sustain control determines the final value the envelope rests at after the decay portion has ended.
Gated Looping Envelope - ADSR loops whilst gate signal is high.
Looping Envelope - ADSR loops regardless of gate signal.
LIN response (Hold switch to select between LIN/EXP Mode) - Sets the envelope response to be Linear. The response is Exponential when the status LED is off.
When the envelope is looping, all 5 controls affect the output. Attack and Decay operate, as one would expect. The Sustain control sets the minimum voltage the decay part of the envelope will decay to. The Release sets a release time from the end of the Sustain period to the beginning of the next cycle. When the Sustain is set to 0 you can use the Release control to add a delay between the Attack and Decay cycles.

In Normal Envelope mode the Sustain CV input can be used with an LFO source to add amplitude modulation that gradually increases as the Envelope transitions from the Attack/Decay part of the envelope into the Sustain part. The Level CV is also a useful point for amplitude modulation or can be used for Velocity Sensitivity via CV.

The Time CV is set so that increasing voltage shortens the overall envelope time to better mimic the sounds of percussive instruments.

Features:

5 Modes of Operation: Gate Input ADSR, Trigger Input ADS, Gated Loop, Constant Loop and EXP/LIN Envelope Responses
CV over: Attack, Decay, Sustain, Release, Level and Time
Works with Gate or Trigger Signals from +5V to +12V
CV Input Range 0V to +10V
Output CV Range 0V to +10V


Power consumption: 28mA at +12V and 18mA at -12V
Depth: 25mm
HP : 6

Notes: The updated "Skiff friendly" design of the mml filter now features bipolar "Attenu-verters" for the cv controls as well as an all new red mode!

This new mode activates a feedback distortion circuit capable of actually changing the pitch of the notes coming in to the filter in a musical way that adds instant variety to acid basslines, creates weird and strange alterations to drones or adds some nice overdriven distortion to whatever goes into it!

The multi-mode ladder (mml) filter is based on the classic transistor ladder low pass filter by dr. Robert a. Moog. This filter updates the classic 4-pole ladder design to provide band pass and high pass filter responses as well as the traditional low pass filter. There are 2 bipolar controls with attenu-verters for the cut-off frequency plus a cv input for the resonance.

The core of the circuit features a fully discrete transistor design with an op-amp buffered output, this allows soft saturation of the input signal to get the classic overdriven tones of the ladder filter. A bass compensation circuit has been included to retain the bass response in low pass mode when the resonance is increased. The bass compensation also helps to improve the response of the high pass filter.

The red mode is activated/de-activated by holding the mode button for 0.3s. In this mode the filter cut-off, input volume and resonance all interact and the effect is to produce alterations to the incoming frequencies. The pitches of the audio coming into the filter also affect the alterations as well selecting between low pass, band pass and high pass filter modes whilst in red mode.

Features

Low pass, band pass and high pass modes.
Red mode feedback distortion.
CV controlled resonance.
Added low frequency compensation.
Soft saturation of input.
2 x bipolar attenuverter CV inputs.

Width: 6 HP
Depth: 25mm
Power: +12v = 50ma / -12v = 39ma

Notes: The Timbre is a 6HP Eurorack module based on the wave folder section of the Buchla 259 oscillator as implemented in the Music Easel.

The wave folder adds extra harmonics to input signals that have low harmonic content to create rich and interesting timbres. Typical input sources to use would be Sine and Triangle waves but you are welcome to try other sources as well! The Dannysound Timbre adds an extra input to the Buchla design to allow 2 oscillators to drive the wave-folder simultaneously - this dramatically increases the range of possible tones that can be generated and allows the folder to go wild!

Features:

Osc1 / Osc2 Mix - Adjusts the mix between the Oscillator 1 and 2 inputs, also acts as an attenuator if only one input is used.
Timbre Control - Adjusts the overall amount of wave fold
Timbre CV - Bipolar (attenuator) controls the Timbre CV input
Symmetry - Adds an offset to the input so that the top half of the wave begins to fold earlier
Blend - Mixes between the clean and effected sound

Power consumption: 46mA at +12V and 48mA at -12V

Depth: 25mm

HP : 6

Notes: The Dannysound VU Meters is designed to be used with 2 x Dynamics modules. The modules connect internally via 2x3 pin ribbon cables. The meters provide a visual representation of various signals within the Dynamics modules making settings easier.

Features:

External input sockets for monitoring external sources.

Switch to select high or low meter sensitivity or off if the clicking needles get annoying!

Monitoring of the compression/expansion amount.

Monitoring of the unprocessed input level.

Monitoring of the compressor/expander output level.

Power consumption: 0.03mA at +12V and 83mA at -12V at and 3mA at +5V
Depth: 51mm
HP : 8

Notes: The B32 controller has 32 buttons as you can never have too many buttons. Especially trigger sequencers benefit from this nice button array. The B32 is also a very good match for the M4 motor fader controller, since with the M4 you need buttons for switching fader layers are presets more than pots.

Shipping includes a short ribbon cable for connecting the controller to the master or to the previous controller. If you want to place the controller further away from the master, you can purchaser longer ribbon cables here in the shop.

You can connect up to 16 controllers to each DROID master.

Notes: ***B-STOCK: Box opened, but product is in excellent condition and in perfect working order***

Simple to look at but deceptively powerful, Dreadbox's Telepathy is a full analogue synth in a small module, featuring VCO, low-pass and high-pass filters, LFO, envelopes and VCA.

Supplier's Notes:
Telepathy is a full voice analogue synthesizer module with deep modulation options due to its multi-destination LFO and Envelope. From Bass to Lead sounds, to drums and drones, Telepathy has broad and versatile sound design capabilities. It has a Full Analogue path (Typhon VCO, 4-pole low pass / 2-pole high pass filters, analogue VCA) that is digitally controlled for more precision over its parameters, resulting in a warm, present and distinct Dreadbox sound.

With lots of useful and musical features integrated into a compact size (10hp), and its skiff friendly design, Telepathy is a great addition to small or large Eurorack systems.

Features:

1x Analogue Oscillator with saw, square, -1 oct square sub and noise, plus PW control for square, level for noise and waveshape
Automatic tuning for the oscillator and fine tune
Analogue 24db Resonant Low pass filter with Oscillator FM and Noise FM and 6db High pass filter
Analogue VCA
1x LFO with Free/Key/Track/BPM/BPM Key modes, Fade in, Triangle/Saw/Ramp/Square/Random waveforms, that is mapped to various parameters
2x Envelopes, one dedicated to the VCA with Velocity control and one loopable for Low pass Filter, Pitch and PW
CV in patch that can be mapped to all the basic parameters in parallel with dedicated amount for each parameter
MIDI in/out+through
CC in/out, Program Change in/out
Multitimbral Chaining functionality via MIDI up to 8 modules 16 presets
10HP

Notes: dsp.cpoffee's custom everything-including-kitchen-sink dsp development platform.

At the core of this is an Electrosmith Daisy Patch Submodule, combined with a 12-bit 4 channel SPI DAC [DAC7554], and supporting hardware for more IO

Features
- 8x pots normalled to +5V
- 8x CV in breaks normalled connection and pot acts as an attenuator
- 2x gate in
- 2x gate out
- High-fidelity stereo in/out (Daisy Patch Submodule, using an WM8731 codec)
- 2x 12-bit CV out from Daisy Patch Submodule, scaled to -5v to 10v
- 4x 12-bit CV (or lofi audio w/ some hacking) from external DAC7554, scaled to -7v to 7v
- TRS MIDI in/out (in is auto-sensing for type a/b)
- SD card slot
- Expansion header for +5v, +3v3, SPI, UART, I2C, and USB connections

Notes: The Wave Transformer is a complex single oscillator with 7 audio outputs. Its method of wave shaping differs from other complex oscillators in that it is not based upon classic wave folding such as is common in West Coast synthesis, or filtration such as is common in East Coast synthesis.

This analogue, vintage-voiced, voltage-controlled oscillator features over 8 octaves of accurate pitch tracking. Its 7 simultaneous wave outputs include a unique Complex output. This strange and novel output varies between a simple waveform (triangle, unless you patch a signal into the Shape Insert jack) and a complex transformation of the harmonic structure of the original waveform. It contains a unique mixture of the fundamental frequency, odd order harmonics, even order harmonics and subharmonics. The Sub Octave panel control will determine whether the sub harmonics are derived from one octave down, two octaves down, or are muted altogether. It will vary from a simple waveform to a silhouette of your cat watching you as you react to a "present" that it left for you on the counter. No, seriously.

The module's Transform control morphs from a basic waveform through many strange iterations into a complex, gnarled mass of audio mutations at the Complex output using an asymmetrical multi differential audio transmutation circuit. You can yield countless variations on these permutations by combining this novel circuit with Hard Sync, Soft Sync, Linear FM and Exponential FM.

Additionally, you can mute the source waveform to use the circuit as a harmonic gate/VCA, rendering the Wave Transformer a voice unto itself.

If that is not enough, there is a Shape Insert that allows you to transform external oscillations and modular-level audio sources.

Notes: The classical Eowave synth voice has a new skin matching with the new product line.

The Domino is an analogue all-in-one synth voice with saw/square wave oscillator, ladder type low pass filter, envelope and VCA - it is designed for pure beefiness and grunt in the low end department. It excels at basslines, acid, kicks and low throbbing drones.

The core of the module is a dual waveforms oscillator with saw and square. The pulse width of the square can be modulated with the PWM input.

The pitch knob over a range is of 1 octave, designed to be used primarily in lower ranges. The CV input control the oscillator pitch in v/oct but is also normalised to the f Mod input. When the f mod potentiometer is fully open, the filter can be controlled in v/oct. Since the filter as self-oscillation capabilities, you can also use it as an oscillator.

The decay envelope is controlling the filter cutoff and is normalized to the oscillator pitch input.

The Domino provides two envelopes control options with its gate>VCA and envelope>VCA switch, allowing you to choose between using a gate signal or the decay envelope to shape the VCA response.

The Mix knob enables blending between the saw and square waves. Connect external sound sources to the Mix 1 and Mix 2 inputs to replace the saw wave and square wave, respectively.

This module also provides the dry oscillator waveforms output as well as the envelope output.

Main features:
Fully analogue synth voice
Dual waveform oscillator with control over the pulse width
Ladder filter with v/oct tracking and self oscillation
VCA
Decay envelope responsive to the amplitude of the gate
External inputs going thru the filter/VCA signal patch

Some applications:
Bass synth voice
Envelope generator
External source mixer
Kick drum

Technical details:

Fully Analogue design
10hp
Reverse power protection

Notes: Six-voice (or three stereo channel) mixer in a small format, the Supamix takes a straightforward but highly effective approach. Swap functions allow for creative approaches to mutes, randomisation and sequencing.

Supplier's Notes:
A compact stereo line mixer created with live performance and space optimisation in mind. This 6-channel stereo mixer has a fully analogue audio path with 2 VCAs per channel controlled by fines tuned analogue envelopes to minimise mute clicks. It also embeds a unique mute swap function with 6 modes allowing you to automate muting.

Supamix is a compact stereo line mixer designed for live performances and space optimization.
This 6-channel stereo mixer features a fully analogue audio path with 2 VCAs per channel and finely
tuned analogue envelopes for vactrol-like muting control minimizing mute clicks.

Supamix also includes a unique mute swap function with six modes, offering versatile
mute automation possibilities.

The mixer is designed with a variety of input options to accommodate different needs while
being compact:

- Inputs 1/2 have manual pan controls for placing static sounds within the mix.
- Inputs 3/4 have CV pan controls to moving sound sources in the stereo field
- Inputs 5/6 are stereo, making it easy to mix modules with stereo outputs (right input is normalized to the left) to mix the growing catalogue of stereo modules.

A header on the back allow you to use the L output as a TRS stereo output. Another header is here to link the Supamix with the O phone/line module.

The Swap functions on the modules are both useful for transitioning between sound scenes or creative applications. To change the swap modes on Supamix, press the Shift button and one of the mutes. If you press the Swap button, it will activate the swap manually. The following are the swap modes available.

1 -> Scene change gate : Reverse the mutes states when a gate is high
2 -> Scene change trig : reverse the mutes state when trigged (or if the swap button is pushed)
3 -> Binary counter : CV input between 0 and 5v will correspond to a 6 bit binary counter. At 0v mutes will be all oo, 5v will be all open. And it will count as follow :100000 010000 110000.....
4 -> Randomizer: Trigg to randomize the mutes. You can change the probability of having the mutes on by using a trigger between 2 and 5v.
5 -> Sequencer: Trig to go one step further. It reverse the current step mute state.
6 -> State rotation: Rotate the mute state 0v there isn't rotation, 5v is a full cycle rotation. This shift the mutes state (last one goes to first one)

Main features:

6 voice mixer
Manual pan on 1/2
CV pan on 3/4
Stereo inputs on 5/6
Unique mute swap functions
Linkable to the O output module

Some applications:

Compact case line mixer
Creative mute switching/sequencing
Feedback R out to one of the cv pan input to cv control feedback distortion

Technical details:

10 hp
Fully Analogue signal patch with 12VCAs with envelopes on each.
Skii friendly
Reverse power protection

Notes: Save nearly 50 pounds with Erica's double Pico Drums bundle, including two chainable modules which combine to create a powerful drum and sample setup in a total of just 6 HP.

Supplier's Notes:
Erica Synths Pico DRUM1 module gives you two independent and great sounding drums with versatile control over different parameters and a huge collection of drum samples.

Features

2 independent drums
64 samples for each drum
USB interface for user sample upload
Independent control over Pitch, Decay and Level for each drum
Independent control over Pitch, Decay and Level for each drum
Separate triggers for each drum
Audio output of mixed drum sounds
Exclusive switch to select how the two drums interact with
Each other when triggered at the same time
12bit resolution, 44kHz sampling frequency

You can chain up several Pico Drums and get one of the smallest modular drum setups in the modular world!

With Pico Serie, the question was posed - is it possible for ANY superior functionality synth module to be wide 3HP wide and affordable? Yes, it is.

Technical specifications:

Resolution: 12 bit
Sample rate: 44 kHz
Power consumption: +35mA, -15mA
Module width: 3HP
Module depth: 35mm

Notes: ***B-STOCK: Box opened, product in perfect working order***


Erica Synths Black Hole DSP 2, an updated version of Black Hole DSP features 24 custom effects, designed in close co-operation of Erica Synths team rider KODEK and creator of SpinCAD software Gary Worsham. Each effect has 3 manually and CV controllable parameters, manual and CV control over sampling frequency for spanning from 48kHz to really Lo-Fi crunchy sound and full analogue dry/wet control. All effect parameter settings can be saved to the memory and instantly recalled with the effect, which makes Black Hole DSP II ideal for live performances.

Notes: The Erica Synths Black Stereo Delay is a hi-fi stereo delay with a lot of unique features based on our custom DSP engine. Tape, BBD and digital delay emulations with three modes, each accompanied with delay time, feedback, feedback tone and stereo spread controls allow for designing extremely delicate effects. CV control over various parameters and the ability to save up to 10 presets will make this module an integral part of any performance rack. Delay effects are developed by Dutch company www.112db.com

Features

Tape, BBD and digital delay types
Three modes for each type
Tap and clock synchronization of delay time
10 preset patches
CV control over delay time, feedback, tone, dry/wet mix and preset selection
Adjustable stereo delay spread
The modules run on new Erica Synths DSP hardware and the effects are developed in collaboration with Dutch company 112.dB who make some of the most beautiful sounding effects.

Erica Black Series include high-end, unique functionality and superior quality modules. Only the best, highest-quality components are used, all inputs and outputs are protected against undesired overvoltage. Erica Black Series consist of range of modules that are needed to put together entire synth.

Technical specifications:

Max audio input level before clipping: 16Vptp
CV input range (full span): -5V - +5V
Sampling frequency: 48kHz, 24bit
Delay time: 3..3000ms
Audio codecs: -108 dynamic range, -98dB THD+N
Power consumption: 120mA@+12V, 39mA@-12V
Module width: 12HP
Module depth: 35mm

Notes: The Erica Synths Black Reverb is a versatile hi-fi stereo FX module with lots of unique features based on Erica Synths' custom DSP engine. The reverb sources are selectable Tape, BBD and "dirty BBD" digital; emulations with three modes, each - Room, Hall and Cathedral. Delicate room size control, feedback, feedback tone and stereo spin controls allow for designing extremely delicate reverberation effects. CV control over various parameters and the ability to save up to 10 presets will make this module an integral part of any performance rack.

Features:

Reverb based on Tape, BBD and digital delay lines
Three room sizes
Manual and triggered FREEZE with 1V/oct tracking
10 preset patches
CV control over size, feedback, tone, dry/wet mix and preset selection
Adjustable stereo spin

Specs:

Max audio input level before clipping 16Vptp
CV input range (full span) -5V - +5V
Sampling frequency 48kHz, 24bit
Audio codecs -108 dynamic range, -98dB THD+N
Power consumption 120mA@+12V, 39mA@-12V
Module width 12HP
Module depth 35mm

Notes: ***B-STOCK: Box opened, but product is in excellent condition and in perfect working order***


The Erica Synths Black Reverb is a versatile hi-fi stereo FX module with lots of unique features based on Erica Synths' custom DSP engine. The reverb sources are selectable Tape, BBD and "dirty BBD" digital; emulations with three modes, each - Room, Hall and Cathedral. Delicate room size control, feedback, feedback tone and stereo spin controls allow for designing extremely delicate reverberation effects. CV control over various parameters and the ability to save up to 10 presets will make this module an integral part of any performance rack.

Features:

Reverb based on Tape, BBD and digital delay lines
Three room sizes
Manual and triggered FREEZE with 1V/oct tracking
10 preset patches
CV control over size, feedback, tone, dry/wet mix and preset selection
Adjustable stereo spin

Specs:

Max audio input level before clipping 16Vptp
CV input range (full span) -5V - +5V
Sampling frequency 48kHz, 24bit
Audio codecs -108 dynamic range, -98dB THD+N
Power consumption 120mA@+12V, 39mA@-12V
Module width 12HP
Module depth 35mm

Notes: The STEREO FX module brings hi-fi stereo effects into the Erica Synths Drum Series. Based on Erica Synths' new DSP engine, the module provides a wide range of custom delay and reverb effects. CV control over various parameters and the ability to save up to 10 presets will make this module an integral part of any performance rack.

Features

Hi-Fi stereo FX module
3 delay and 3 reverb effects
Tap and clock synchronization of delay time
Delay time divisions and multiplications in sync mode
10 preset patches
CV control over delay time, feedback, and preset selection
The FX is developed in collaboration with the Dutch company 112dB which offers some of the best-sounding VST instruments.

Technical specifications:

Audio input level: -5V - +5V
Delay time: 3ms - 3s
CV level (full span): -5 - +5V
Power consumption: +123mA, -40mA
Module width: 10HP
Module depth: 35mm

Notes: ***B-STOCK: Box opened, but product is in excellent condition and in perfect working order***


As probably many of you know the MIX BX (like Feedback's PRE BX channel strip) is based on a very popular mixer used by techno artists in the nineties and loved for its specific sound.

Tech specs:

- 35HP front panel
- 35mm depth behind front panel including the power connector
- 6 mono input jacks ( 1 per channel)
- Pot controls for channels : Gain, Hi, Low, Aux1 send, Aux2 send, Pan, Volume
- 6 mute switches (1 per channel)
- Pot controls for master : Master Level, Headphone Level, Aux1 Return, Aux2 Return
- 2 x mono aux send jacks
- 4 mono input jacks for two stereo Aux returns
- 2 jacks for master left and right out
- one 3.5mm stereo jack for headphone out
- boxed 10 pin euro power (+12V / -12V)

- Input Level from -50dBm to -10dBm
- EQ Hi +-10dBm/10kHz shelf type
- EQ Low +-10dBm/100Hz shelf type
- Output Level 20Vpp

Notes: Advanced generative sequencer featuring mutes per channel and transposition facilities.

Akropoli is an extension and enhancement of our successful Little Melody and High Towers modules, offering the features of both of these modules as well as some of it's own unique features such as mute buttons per channel, manual transpose knob and 1V/oct transpose CV input. Akropoli operates using Frequency Central's proprietary TOOL V2 code, and can count in integers as well as multiples for even more subtle and evolving variations.

Akropoli is a generative sequencer based around clock divisions and a chromatic quantiser, used to create in-the-moment licks and riffs. It is more that the sum of it's parts.

Akropoli's internal operations can be considered as 4 clock dividers patched into a CV mixer via attenuators. The attenuators select notes over a 5 octave range, the clock dividers determine how often those notes are added to the mix. The final output of Akropoli is quantized chromatically for fast set up and continuously pleasing results. Akropoli has an onboard transposition knob, as well as a 1V/oct transposition CV input.

The 4 clock dividers are labelled A, B, C, and D. They all receive clocks from the same source, the divisions may be selected using the presets and the individual division selectors. The clock dividers can be set to count up, down, or to one of a variety of modes that move between counting up and down. For further information on Presets and Modes see the Little Melody User Guide.

Additionally, each clock divider has it's own binary output (either high or low), these 4 outputs can be used to clock/gate/trigger other stuff on other modules to great effect.

Product Specifications

12V draw
50mA

-12V draw
36mA

5V draw
0mA

Depth
35mm

Notes: Expandable 4 channel VCA based stereo mixer with tone shaping and FX bus.

Chipset:

For this item, Frequency Central offer a CHIPSET which contains the following:

3 x LM13700

For all other components required, please see the build document.

Features:

4 x input channels, each featuring LEVEL, HIGH, LOW, FX send, PAN, MUTE and CV control of level.
FX send and stereo return + FX phase jumper
Left and Right Eurorack level inputs (2 x 3.5mm sockets)
Left and Right line level outputs (2 x 6.35mm sockets)
Scribble strips!

Strips is also expandable! You can add a second strips, connected to the first via a 16 pin to 16 pin cable. The cable powers the second Strips and gives you 8 channels to play with. The second Strips accesses the first Strips FX bus. When using in expanded configuration, the FX send/return and main outputs for the second Strips are not available. Here's how!

FX phase jumper - because not all FX that you might use in the FX loop are in phase with respect to their input/output. The phase jumper allows you to compensate for this and avoid weird phase cancellations.

Product Specifications

12V draw: - 43mA
5V draw: - 0mA
-12V draw: 43mA
Depth: 39mm