100% Sicheres Einkaufen

Studio equipment

Our full range of studio equipment from all the leading equipment and software brands. Guaranteed fast delivery and low prices.

Visit Juno Studio

100% Sicheres Einkaufen

DJ equipment

Our full range of DJ equipment from all the leading equipment and software brands. Guaranteed fast delivery and low prices.Visit Juno DJ

Synth modules

View:
Options
Artikel 1 bis 50 von 135 auf Seite 1 von 3 anzeigen
1  2  3  »
Subscribe to our weekly Studio Equipment emails
Cat: 589495 Rel: 10 Dec 15
 
Dual envelope generator synthesiser module - 20HP wide
Notes: The Pingable Envelope Generator (PEG) from 4ms is a dual envelope generator whose envelope lengths are set by incoming clocks or "pings".

The PEG has full CV control of envelope shape, skew, and ping (clock) division/multiplication, as well as a plethora of triggering and cycling options (AD, AR, quantization, cycle), and a tap tempo button for each channel.

Scaling/shifting:
- Scale knob is an attenuating inverter for main envelope output (Maximum 0V to +10V non-inverted, and Minimum -10V to 0V inverted).
- Bi-polar button centers main envelope output around 0V (-5V to +5V output)
- "+5V ENV" jack is a non-scaling output that always produces a 0V to +5V envelope, regardless of Scale and Bi-polar settings
- "OR" jack outputs an analog OR of the two scaled envelope curves. This outputs the highest value from either envelope at any given moment, taking into account the Scale and Bi-polar controls.

Gate outputs:
- End-of-Rise (EOR) gate output goes high when envelope finishes a rise portion, and goes low when envelope begins a rise portion
- End-of-Fall (EOF) gate output goes high when envelope finishes a fall portion, and goes low when envelope begins a fall portion
- Jumper for each channel changes EOR output to a Half-Rise gate output. The Half-Rise jack goes high when 50% of the time of the rise portion has elapsed, and goes low after 50% of the time of the fall portion. Using the Skew parameter, this jack provides a variable phase gate output useful for quadrature effects and clock phase shifting and trigger delay effects. Factory setting is EOR for red channel, Half-Rise for blue channel.

Triggering/cycling:
- Cycle button for each channel forces envelope to self-cycle in sync with the ping clock (LFO mode). Button lights up when in cycle mode.
- "T" jack toggles the state of both channels' Cycle button when a gate is applied
- "QNT" jack for each channel triggers an envelope to start at the next quantized beat, with respect to the divided/multiplied ping clock. Holding a gate high on this jack causes the envelope to repeat.
- "Async" jack for each channel causes an envelope to output immediately (asynchronously). Holding a gate high results in an AR envelope (rise-sustain-fall). If cycle mode is enabled, the envelope will continue to cycle at this new phase with respect to the ping clock. Phase can be reset to being in sync with the ping clock by pressing the cycle button or applying a pulse to the QNT jack.

CV input jacks:
- CV control of Ping Div/Mult, Skew, and Curve using the CV jacks. Respective knobs set the center offset for the applied CV
- CV of 0-10V will modulate the parameter's full range However, a 0-5V CV will modulate the parameter within a very useful range.
Read more
 1 in stock $264.93
Cat: 589490 Rel: 10 Dec 15
 
4 channel voltage controlled clock divider/multiplier synthesiser module with master tap tempo - 10HP wide
Notes: Four channel voltage controlled Clock Divider/Multiplier with master Tap Tempo. Each channel can be synced to the tap tempo, to the channel above, or to an external clock. Each channel also has a reset jack.

With a Tap Tempo button and five sync'ed clock outputs, the QCD is a versatile head-of-the-chain "Master" clock module, and/or a complex rhythmic pattern generator.
Read more
 3 in stock $208.61
4ms Wav Recorder Module (synth module)
Cat: 648950 Rel: 29 Jun 18
 
6HP Eurorack module for recording high-fidelity, low-noise stereo WAV files
Notes: The WAV Recorder from 4ms Company is a high fidelity, two-channel stereo audio recorder with basic playback features. Accepting a wide range of input signals, from line-level to modular-level, the WAV Recorder stores audio onto a microSD card in lossless .wav format up to 96kHz/24-bit. The trigger jack can be used for capturing rhythmic loops or synchronizing multiple WAV Recorder modules for multi-track recording. In Playback mode, the trigger jack or button plays the most recent recording. A simple file/folder navigation system can be used to browse the folders on the card for playing back .wav files. A Gain knob allows for up to +20dB of boost, and an LED Signal Meter indicates clipping and the signal level.
Read more
 2 in stock $226.34
Cat: 739182 Rel: 22 Apr 16
 
B-STOCK: Box opened, product in perfect working order
Notes: ***B-STOCK: Box opened, product in perfect working order***


Highly configurable Control, Modulation, Triggering and Pattern module. 8 simultaneous Outputs and 12, individually assignable, Output types.

Output and Modulation types include Pulses, Gates, LFOs, Digital Noise, Loopable S&H modes and a collection of Arpeggios and Rhythmic Loops.

Tempo-sync for all Outputs is provided by the on-board Clock or
an External Clock Input with Tempo ranges from 20 to 270 BPM.

Outputs can be set to any Clock Division or Multiple from 1/16th
of a Beat to 16 Bars and can be Offset up to 360 Degrees.

Intuitive interface allows user-definable control over knob and parameter behavior to match the preferences of individual users.

For audio, please visit: http://www.abstractdata.biz/products/eurorack/3x/ade32/?tab=audio
Read more
 1 in stock $294.34
Cat: 601494 Rel: 28 Mar 18
 
Sophisticated rhythm creation & manipulation module - 14HP
Notes: Pattern and rhythm creation and manipulation module for creating musically useful rhythms and patterns from a variety of inputs - it's a module that will jam along with you.

36 algorithms in 6 sets covering Variables, Multiples, Probability, Logic, Phase and Gates with configurable CV control over all parameters.

Takes regular clocks and generates rhythmic patterns, takes rhythmic patterns and generates new patterns, takes irregular and random patterns and generates new, irregular and probability-based patterns.

The patterns can be rhythmic, continually evolving or entirely random and can be controlled and manipulated via multiple CV options.

Can also be used as a utility module to perform Clock Division/Multiplication, Phase-Shifting and Logic-related tasks.
Read more
 2 in stock $204.44
Click for better price!
quote 601494
Cat: 655470 Rel: 03 Jul 17
 
Envelope generator module - 21 HP
Notes: The ADSR envelope from the Japanese 100m system is well-known for its percussivity and the enormous punch. ACL gives us three of them in one single Eurorack module, the Envelope X3.

Sometimes an envelope generator doesn't have to be function-ladden, but just reliable, solid and good. This is what ACL achieves with the Envelope X3 module. The technical quality originates in precision components, as used in measuring instruments for instance, in order to keep the parameters exact, always the same and to keep you happy.

Three identical, classic Attack-Decay-Sustain-Release envelopes are integrated; function-wise rather simple with a gate input and one positive and one inverted envelope output each. The gate inputs are normalized (1 -> 2 -and 1 -> 3; with input 1 as master) which minimizes the amount of patch cords. Normalizations can be disrupted by patching a cable.

Each envelope generator has a time range switch with two positions to select between short and long envelope times.

The LEDs for visualisation were omitted to keep the power consumption low.
Read more
 1 in stock $258.68
Cat: 673542 Rel: 23 Feb 18
 
Analogue multi-tap phaser - black faceplate
Notes: Mega-Phase 12 is an analogue stereo phaser with beefy, very vocal sound. The module is based on the effect pedal Small Stone developed by Electro Harmonix. In contrast to the classic, here you don't have four, but up to twelve stages at hand. The resonance can be picked up from different points in the signal path. Thanks to several inputs and outputs, it is possible to patch a second, external feedback loop with additional effects. Without a doubt the most flexible phaser module on the market.
Read more
 2 in stock $299.35
Cat: 698445 Rel: 09 Aug 18
 
Analogue multi-tap phaser - silver faceplate
Notes: Mega-Phase 12 is an analogue stereo phaser with beefy, very vocal sound. The module is based on the effect pedal Small Stone developed by Electro Harmonix. In contrast to the classic, here you don't have four, but up to twelve stages at hand. The resonance can be picked up from different points in the signal path. Thanks to several inputs and outputs, it is possible to patch a second, external feedback loop with additional effects. Without a doubt the most flexible phaser module on the market.
Read more
 1 in stock $299.35
Cat: 708087 Rel: 23 Jan 19
 
Sample & Hold, Track & Hold, Gated Slew, Clock & Noise generator - black, 12HP
Notes: A real powerhouse module that takes up only 12 HP of rack space. It can generate random and pseudo random control voltages, staircase waveforms, deliberate aliasing of audio signals, portamento type effects, adjustable audio range noise and has many other uses too.

It can be switched between Sample & Hold or Track & Hold modes, and the unique "Restrict" control affects the way the hold output changes with respect to the current input level and previously held output level. With the control fully off the unit behaves just like any other S/H, but at fully clockwise the output is restricted to move by only a small amount after each new sample. The output will still have the same range as the input, but will need more hold commands to get there. This versatile Sample and Hold circuit was designed by Tony Allgood, and is built under licence from Oakley Sound.

The Sample Hold & Slew module also includes a very well featured Slew generator, which includes a Gated Slew function. It can be used independently or chained with the S&H module. Slew mode can be switched between Linear or Exponential Slew types. There is a Gate input, so that the Slew on/off can be switched using an External CV (Gated Slew), and also the Slew control logic can be reversed by a toggle switch that doubles as a manual Slew on/off switch. In addition, it has slew up only, slew down only or slew up and down modes, which are selected with a three-way toggle switch. An indicator LED lights when Slew is active

There is also an inbuilt analogue Noise generator, which is normalised to the input of the Sample and Hold section, and there are both regular and clipped Noise outputs - the Clipped Noise is particularly useful with the sample and hold section, as it is weighted to produce higher random voltages. Both Noise outputs are fed through an internal "Noise Colour" control - at centre position it allows the noise through unfiltered, turning the control anti-clockwise introduces low pass filtering of the Noise, and rotating it clockwise introduces high pass filtering. The Noise source itself is based on an analogue band gap shunt regulator configured in avalanche mode, and it generates white noise with a gradual roll off above 8kHz. It is a little "grainier" in character than the noise from our MiniMod Glide & Noise module (which uses a reverse biased transistor as a noise source), so is a useful compliment to this module as it does not generate exactly the same sounding Noise

Lastly, it includes a wide range clock generator with a rate LED. The range is from one cycle every thirty seconds to around 2 kHz and the clock output is normalised to the Clock Input of the S&H section. It also has a Clock Out jack so that it can be externally patched to other Eurorack modules.
Dimensions: 12HP wide, 26mm Deep
Current draw: 55mA Positive, 40mA Negative
Read more
 2 in stock $215.91
Click for better price!
quote 708087
Cat: 688824 Rel: 01 Aug 18
 
Analogue waveform animator & dual channel device - black, 14HP
Notes: The WaveSwarm is a waveform animator and all analogue dual channel device.

Each channel simulates up to six VCO's beating in unison with a different beat frequency between each animation. The fixed beat frequencies are generated by twelve onboard LFO's, and the front panel pots control the level of each of the six animators, along with the level of the dry signal to the final mix. In addition to independent channel inputs and outputs it also has an A+B output, which sums the outputs of the two channels, creating an effect similar to twelve VCO's in unison! This is possible because channel B uses slightly different beat frequencies to channel A, they are not identical.

The input waveform can be saw, triangle, sine or wavetable/complex waveforms, in fact most waveforms with the exception of square or PWM waves will give some form of animation.

A soft clip circuit is built in so that at higher signal levels the signal magnitude is limited by rounding the top and bottom of the waveforms, thus slightly softening the sound. There are soft clip LED indicators for both channels.

It can produce huge, fat drones or supersaw type waveforms from a single sawtooth or triangle wave input.
Read more
 1 in stock $278.49
Click for better price!
quote 688824
Cat: 737861
 
B-STOCK: Box opened, product in perfect working order
Notes: ***B-STOCK: Box opened, product in perfect working order***


The WaveSwarm is a waveform animator and all analogue dual channel device.

Each channel simulates up to six VCO's beating in unison with a different beat frequency between each animation. The fixed beat frequencies are generated by twelve onboard LFO's, and the front panel pots control the level of each of the six animators, along with the level of the dry signal to the final mix. In addition to independent channel inputs and outputs it also has an A+B output, which sums the outputs of the two channels, creating an effect similar to twelve VCO's in unison! This is possible because channel B uses slightly different beat frequencies to channel A, they are not identical.

The input waveform can be saw, triangle, sine or wavetable/complex waveforms, in fact most waveforms with the exception of square or PWM waves will give some form of animation.

A soft clip circuit is built in so that at higher signal levels the signal magnitude is limited by rounding the top and bottom of the waveforms, thus slightly softening the sound. There are soft clip LED indicators for both channels.

It can produce huge, fat drones or supersaw type waveforms from a single sawtooth or triangle wave input.
Read more
 1 in stock $260.77
Cat: 648928 Rel: 25 May 17
 
Compact programmable clocked modulation source in Eurorack format - 8HP
Notes: 'Pamela's NEW Workout' is a compact programmable clocked modulation source for your Eurorack modular synthesiser system. It provides 8 highly editable outputs producing various control voltage signals correlated and synced to a BPM based master clock.

Building on the original 'Pamela's Workout', this new evolved model maintains the original's form factor and intuitive workflow but greatly improves on and adds many new features with upgraded hardware, a new OLED display and rewritten software.

Each output is now able to provide not just clocked triggers but also rhythmic waveforms with many parameters controllable directly and via assigning to external CV control. Pamela has grown beyond a clever clock and now provides almost limitless synced modulation possibilities.

Improvements have been made to overall clock stability and integration with external clocks and devices. Also new are dedicated MIDI and Din Sync clock outputs available via optional expander modules.
Read more
 More than 10 in stock $223.21
Click for better price!
quote 648928
Cat: 688775 Rel: 31 Jan 19
 
Flexible five stage function generator - 19HP
Notes: The 'Quaid Megaslope' is a five stage function generator or modulator which operates in one of 3 modes; a multistage 'CZ' or 'Juno' style complex envelope, a super flexible LFO and a step sequencer with per step programmable slew or slides.

Each mode produces a varying output voltage moving from point to point across a set number of chained together stages. Each stage features a destination level, an overall rate or time to reach its destination level and a variable slope for the output path to take. As well as direct control, every stage feature voltage control of both level and rate. There are both unipolar and bipolar voltage outputs together with triggers emitted for the end of each stage and the end of a full cycle.

The Quaid Megaslope is designed to be fun, flexible and intuitive to use.
Read more
 3 in stock $227.38
Click for better price!
quote 688775
Cat: 688796 Rel: 11 Feb 19
 
MIDI to CV module featuring 4 channels of CV & Gate - 7HP
Notes: 1983 is a polyphonic MIDI to CV interface with creative voice allocation and automatic tuning capabilities. There are 4 channels of CV and GATE outputs that can be used in various layouts such as hybrid splits between monophonic and polyphonic voices or velocity, CC, aftertouch, triggers, clock or reset.

Each channel is able to LISTEN to the simple waveforms of the oscillators and with a single press of the TUNE button, it adjusts the CV outputs to the same tuning (such as A = 440 Hz in equal temperament or others). It also maps the response for all 7 octaves so all the oscillators are perfectly in tune with each other (and with other instruments). PURE MAGIC!

When the UPDATE jack is used, it forces the outputs to update only when a trigger is detected.

1983 always stores the notes played in a legato sequence in a buffer and the WINDOW jack allows for selecting which of these notes appear at the outputs.

This way the MIDI keyboard can be used as an input interface for harmonies and note sets that are further creatively processed with triggers and CV in the modular environment.

The TRANSPOSE jack shifts the outputs by semitones, fifths or octaves and the PORTAMENTO jack sets the glide time by CV.
Read more
 2 in stock $289.97
Cat: 668637 Rel: 09 Nov 17
 
6-channel performance mixer with EQ's & mutes
Notes: Hex mix VCA is a compact six channel VCA with an unique response curve range from logarythmic to linear and to exponential using a pot.

All outputs are routed to output six to act as a mixer, with a normalization of each one to remove each VCA from the Mix.

Hexmix VCA can act as six independent VCAs as well as a Mixer for all the inputs (Selectable via a switch). Featuring an internal connection to interface with our Hexmix system.

Every VCA has a response pot for the incoming CV, being full logarythmic at maximum setup and full exponentiall at minimum setup, having the linear response in the centre position.

The pot provides the full range of responses to adecuante to our prefered application, such as percusive sounds or panning effects.

Level pot of each channel is an attenuator of the signal coming out of each VCA.

Jacks are normalled to 10 volts, so when we have no CV present VCA would be fully open and our Level pot will act as a volume.
Read more
 1 in stock $279.54
Click for better price!
quote 668637
Cat: 736449 Rel: 15 Jul 19
 
Facilitates effects processing between eurorack, guitar pedals & electronic instruments
Notes: Want to connect outboard gear to your eurorack synthesizer without taking up valuable HP in your case? The INTRFX allows eurorack-level signals to be processed with pedals and/or outboard effects, and also allows line-level instruments to be processed with eurorack modules. Each of its three channels has an Interchange Switch to swap this mode, as well as an FX Blend parameter which can be controlled via CV. Because of its compact physical design, the INTRFX can be placed almost anywhere and connected to eurorack systems with 3.5mm patch cables rather than bulkier 1/4-in cables.

Feedback effects can be achieved by switching into the "wrong" mode, sending the FX return back into the FX send, while still allowing for dry signal blend and modulation. Channels can also be patched into one another and toggled between modes for experimental routing. Conveniently, each channel can operate as a reversed linear VCA for both audio and DC signals if no effects are used.

Whether you'd like to patch eurorack through some classic pedals or run a drum machine through your gnarliest modules, INTRFX makes these connections easy and flexible.
Read more
 More than 10 in stock $216.95
Click for better price!
quote 736449
Cat: 688790 Rel: 23 Jan 19
 
High energy sound processor for Eurorack - 13HP
Notes: Dark Matter is a high energy sound processor and signal generator that unleashes the crazy raw power of audio feedback into your Eurorack system. It's inspired by "no input" mixer feedback techniques that explore the complex natural behaviours of amplifier circuits pushed beyond their limits. Dark Matter brings this behaviour to the modular synth, adds voltage control to everything, tons of patching options and a big ol' bag of tricks for making feedback a truly *playable* effect.

Things to do with Dark Matter:

- Excite audio signals to the breaking point with 4 flavours of voltage-controlled overdrive
- Turbo charge percussive hits and drum beats
- Add sub-octave tones and timbral richness to melodies and bass lines
- Tweak your tone with a crunchy overdriving 2 band EQ
- Add signal ducking and gating effects with the built-in envelope follower
- Go the feedback way and create meandering loops through your rack using the 10 I/O jacks...
Read more
 2 in stock $293.10
Click for better price!
quote 688790
Cat: 682321 Rel: 30 Apr 18
 
Complex 12-stage phase shifter with separate in- and outputs for all phaser stages
Notes: Module A-101-3 is a 12-stage phase shifter with vactrols as phase shifting elements. Vactrols are known for their smooth sound behaviour. In contrast to other phaser designs, the A-101-3 is much more flexible and offering a lot of new features not available from other phasers on the market. The main difference is that the Doepfer design offers access to each of the 12 input and output stages leading to a lot of new filters that cannot be obtained in other ways. Especially the free patchable feedback loops (yes, not only one feedback loop is possible) between each of the 12 stages, the separate phase shift control for the stages 1-6 and 7-12, and the 2 polarizers intended to control the feedback loops lead to completely new filter types (a polarizer is a circuit that is able to generate positive and negative amplifications in the range -1...0...+1 with -1 = inversion, 0 = full attenuation, +1 = unchanged signal, for details concerning the polarizer function please look at the A-133 VC Polarizer or A-138c Polarizing Mixer module).

Internally, the module is made of 2 independent 6 stage phase shifters (1-6 reps. 7-12) with separate audio inputs (with attenuators), audio outputs (with mix control), and phase shift control units. The phase shift control units feature both manual and voltage-controlled phase shifting (e.g. from a LFO, ADSR, Random Voltage, Theremin CV, Foot Controller CV ...). For each sub-module a phase shift display (LED) is available. The LED shows the illumination state of the 6 vactrols of the sub-module in question as it is connected in series with the internal vactrol LEDs.

Each of the 12 phase shift states is equipped with an audio output socket and feedback input socket to obtain full flexibility to create a multitude of different filters. The audio input signal and the output signals of stage 6 resp. stage 12 are mixed with 2 manual controls to obtain effects at two audio outputs (for normal phase shifting effect this is 50% input signal and 50% phase shifted signal). The two submodules are internally connected via normalized sockets so that two 6 stage phase shifters can be obtained without external patches. Audio output of stage 6 is normalized to audio input of stage 7 and CV input 1-6 is normalized to CV input 7-12. But due to the open structure of the module even other stages than stage 6 and stage 12 can be used as outputs to generate different sounds (simply patch the desired stage output to the normalized mix input socket).
Read more
 2 in stock $258.67
Cat: 698542 Rel: 14 Aug 18
 
Sound source deriving four subharmonics from an incoming square wave signal - 26HP
Notes: Module A-113 is a new sound source that derives four so-called subharmonics (German: Subharmonische) from an incoming pulse signal. The term subharmonics was introduced by Oskar Sala in connection with his so-called Mixtur-Trautonium. A subharmonic means in this context a sawtooth wave (German: Kippschwinger) whose frequency is derived from a master frequency and the master frequency is an integer multiple in the range of 1...24 of the subharmonic - in other words: the master frequency is divided by an integer 1...24 to obtain the subharmonic.

The output waveform of a subharmonic is sawtooth (as also used in the original Trautonium) and not sine. The term subharmonics is somewhat misleading. The master frequency comes e.g. from an A-110 or A-111 to the frequency input of the A-113. The frequency dividers of the 4 subharmonics is adjusted with up/down buttons as displayed with two character LED displays. The subharmonics are available as single outputs and as mix output with adjustable levels for the subharmonics.

Two gate type control inputs enable to select between 4 different mixtures, i.e. 4 different settings of the frequency dividers. In the original Trautonium these are controlled by foot switches to switch between 3 mixtures while playing (the original Trautonium has only 3 mixtures available but with the 2 gate inputs of the A-113 four different settings can be addressed).

Additionally, the A-113 features a mixture memory with 50 presets. Each preset consists of 4 mixtures that can be selected with the gate inputs, each mixture contains the values of the 4 frequency dividers.
Read more
 1 in stock $229.47
Click for better price!
quote 698542
Cat: 738639 Rel: 09 Jul 19
 
Four voltage controlled LFO's/ VCO's with triangle & rectangle outputs in one single module - 22HP
Notes: Module A-143-4 is a fourfold voltage controlled low frequency oscillator (LFO). As the frequency range includes moderate audio frequencies it can be used as a four-fold VCO too.

- Four independent VCLFOs/VCOs with triangle core
- Frequency range switches: low (bottom position) = LFO mode, high (top position) = VCO mode
- Two frequency control CV inputs for each unit
- CV1 without attenuator (~ 1V/oct)
- CV2 with attenuator
- Manual frequency control
- Internal jumpers for the frequency range of the manual frequency controls:
- Jumper not installed: ~ +/- 1 octave range (mainly for VCO applications)
- Jumper installed: ~ +/- 5 octaves range (mainly for VCLFO applications)
- Sync inputs: Combined Reset/Direction inputs for unit #1 - #3 / Separate Reset and Direction inputs for unit #4 (normalled sockets, i.e. Reset is connected to Direction if the Direction socket is unused) / Up/both/down direction switch for unit #4, for technical details concerning the Reset and Direction function please refer to the sketch below
- Triangle and rectangle outputs for each unit
- Typ. output voltage range -5V ... +5V for both outputs (i.e. about 10 Vpp, symmetrical with reference to 0 V)
- Red/yellow LED displays for the triangle outputs (red = negative output voltage, yellow = positive output voltage)
- Common control section with two CV inputs and manual control (these inputs and controls affect the frequency of all four units)
- Sum outputs for triangle and rectangle with red/yellow LED displays
- Optional ultra-low frequency mode: for this a negative voltage can be applied via a jumper internally to the CV2 input of each unit and the common section (i.e. a negative voltage is normalled to the socket CV2 in question). Then the CV2 - - Attenuator control works as a negative frequency control (i.e. turning up this control lowers the frequency). Herewith LFO periods up to about one hour (or even more) are possible.
- Optional CV bus access via jumper (i.e. the module can pick up the CV from the A-100 bus, e.g. generated by a Midi/CV or USB/CV interface A-190-x or a bus access module A-185-1/2), if the jumper is installed the bus CV affects all four units as the bus CV is added to the CV generated by the common control section
- Typ. frequency range: < 0.001 Hz (~ one hour, LFO mode with ultra-low option) ... 15 kHz (VCO mode with installed frequency range jumpers for the manual frequency controls)
- Heat-up time: ~ 15 minutes (required to heat-up the main circuit by the affixed oven)

The module was planned mainly as a quad VCLFO. But we added a range switch (nothing but a switch for two different capacitors) so that even audio frequencies are possible and the module can be used as VCO with some restrictions too. Because of the closeness of the main circuitry (i.e. four VCO cores within less ~ 1 square millimetre) the oscillators may lock if the frequencies are very close to each other and the VCO frequencies interact marginally. If a high quality quad VCO is required the A-111-4 is recommended as this module has four separate VCO circuits available.

The reset circuitry is optimized for the LFO mode. As it takes some time to discharge the oscillator capacitor the discharge time had to be chosen so that the capacitor is fully discharged in LFO mode. In the high range (where a much smaller capacitor is used) this will cause a zero state duration in the 0.3 ms range if the oscillator is synced (during this time the capacitor is shortened for discharge).
The control scale of the inputs "CV1" is about 1V/octave. To improve the behaviour in the VCO mode a tempco circuit is used to keep the temperature of the exponential converter at a fixed temperature (similar to the tempco option of the DIY SYNTH). That way the frequency of the VCOs (and even the VCLFOs) is nearly independent from the environment temperature. But the accuracy (1V/octave scale and temperature compensation) is not as precise as for the dedicated VCOs A-110 and A-111-1.
Read more
 1 in stock $202.35
Click for better price!
quote 738639
Cat: 671601 Rel: 29 Nov 17
 
Analog sequencer for CVs & trigger/gates
Notes: The Doepfer A-155 has two CV rows, each with selectable voltage range, glide and sample & hold options. Three trigger rows and a one gate row. Logic inputs for clock, reset, start and stop. It's even possible to insert external signals per step instead, overriding the CV generated by the 2nd row's potentiometer. The A-155's functions can be expanded by the A-154 Sequencer Controller, as it's an entire control unit with step number limitation, voltage controllable clock generator, variable gate length and a number of playback modes.

Features of the analog rows (knobs):

- 8 potentiometers (knobs)
- Lower row: Scale (knob), voltage output range 0 ... ~ +6,5V
- Upper row: 1V/2V/4V (octave range switch for exact VCO control), voltage output ranges 0 ...1.0V / 0 ...2.0V / 0 ...4.0V
- Glide time (knob), same as portamento or slew limiter
- Glide Control (control input for switching glide on/off)
- S&H Control (control input for internal S&H, works like A-148)
- Pre Glide/S&H-Out (analog output before S&H and glide unit, especially required when external audio signals are used as inputs of the lower row)
- Post Glide/S&H-Out (analog output after S&H and glide unit)
- Lower row: external inputs for the 8 steps (switched jack sockets), control signals or audio signals may be used as inputs (allowed voltage range -5V...+12V), the knobs of the lower row are working in this case as attenuators

Features of the trigger rows (switches):

- 4 Trigger/Gate tracks with 2 rows of switches
- Toggle switches of 1-0-1 type (with middle position), which can be used to send a trigger/gate to the track above or below or to send no trigger/gate (middle position)
- 3 trigger rows (i.e. short pulse for each step set, pulse width corresponds to the pulse width of the clock/step input signal)
- 1 gate row (i.e. a high signal is applied during the length of the step set)

Control inputs and buttons:

- Step (defines the tempo of the sequence, same as clock or trigger input)
- Reset (resets all rows to step 1)
- Start (starts the sequence at the momentary position)
- Stop (stops the sequence at the momentary position)

Step and Reset are compatible to the MIDI interface A-190, i.e. in combination with the A-190 the A-155 may be synchronized via MIDI. The quantizing module A-156 can be used to quantize the infinite analog voltages coming from A-155 into discrete semitone steps (multiples of 1/12V). Without MIDI interface e.g. a LFO rectangle output can be used to define the tempo of the sequence.

The sequencer controller A-154 adds a lot of new functions to the A-155 (e.g. voltage controlled addressing, forward/backward/pendulum/random mode, voltage control of first and last step, voltage controlled clock and gate length, step skipping, combination of several A-155 in parallel/serial mode and many more).
Read more
 1 in stock $261.80
Click for better price!
quote 671601
Cat: 676695 Rel: 20 Dec 18
 
Four-channel MIDI-CV interface for playing polyphonic patches - 16HP
Notes: Module A-190-5 is a four voice Midi/USB to CV/Gate interface. For each voice a pitch control voltage (CV1, 1V/octave standard to control VCOs), a gate output (to control envelope generators) and two additional control voltages (CV2, CV3) are available. The two additional CV outputs can be controlled by Midi velocity, volume, modulation, pitch bend, after touch or free assignable Midi controllers.

- Four voice monophonic (i.e. to control four monophonic voices by four succeeding Midi channels)
- Four voice polyphonic (i.e. to control four monophonic voices by one Midi channel) with several sub-modes (e.g. rotating/non-rotating)
- Two voice polyphonic (i.e. to control two monophonic voices by one Midi channel)
- Unisono

The basic mode is selected by means of a momentary switch (probably Mode or Algor.) and is shown in the LC display. Certain parameters of each mode can be edited (e.g. the midi channel(s), the midi reference note for 0V CV, assigned controllers for CV2 and CV3). For this the momentary switch Edit/Play is used. The parameter values (e.g. midi channels) are shown in the display and can be modified by means of the momentary switches 1...4. In Play mode the LEDs of these four switches display the gate states.
Read more
 2 in stock $264.93
Click for better price!
quote 676695
FORTHCOMING
Endorphin.es Godspeed VCO Module
Cat: 734884 Rel: 01 Aug 19
 
6HP VCO with auto-tuning & octave shift
Notes: The Endorphin.es Godspeed is sort of the single oscillator version of the famous Furthrrr Generator. From its big brother it takes over the digital Thru-Zero core and the legendary wavefolder. But it also has new features like a sub-oscillator output and an immensely practical autotune function.

Especially for people starting with a modular system this oscillator is highly recommended. On 6HP it delivers all the features (and more) needed for diving into the depths of West-Coast-Synthesis!
Read more
coming soon $250.33
Cat: 633328 Rel: 28 Nov 16
 
Full-featured synth module including saw/square wave oscillator, ladder type low pass filter, decay envelope & VCA
Notes: The Domino is a redesign of its desktop synth bigger brother. Packing a full-featured synthesizer voice into 10HP, the Domino includes a saw/square wave oscillator, ladder type low pass filter, decay envelope and VCA. A plethora of patching possibilities makes this module a keen choice for portable systems, and those looking for deep sonic crafting within a tight HP space. Pair with a sequencer for instant basslines and acid lead lines, add some modulation to unlock the full sound design potential

Controls:
- Cutoff - filter frequency
- Res - filter resonance
- Switch - switches between gate>VCA to envelope>VCA
- Pitch - pitch tuning
- Mix - blend saw and square waves
- P Mod - pitch modulation attenuator
- Decay - envelope decay
- Filter Envelope - modulation amount, pre-patched from envelope to filter
- F Mod - filter cutoff modulation attenuator

In:
- CV
- VCA
- PWM (square wave)
- Mix 1 in - input for external oscillator/sound source to replace saw wave
- Gate - gate in
- P Mod - pitch modulation, pre-patched to envelope
- F Mod - frequency modulation for filter cutoff, pre-patched to CV in
- Mix 2 in - input for external oscillator/sound source to replace square wave

Out:
- Saw
- Square
- Env - envelope output
- Out - out from VCA
Read more
 2 in stock $260.76
Click for better price!
quote 633328
Cat: 690950 Rel: 25 Oct 18
 
Stereo effects processor - 16HP
Notes: Erica Synths Black Hole DSP 2, an updated version of Black Hole DSP features 24 custom effects, designed in close co-operation of Erica Synths team rider KODEK and creator of SpinCAD software Gary Worsham. Each effect has 3 manually and CV controllable parameters, manual and CV control over sampling frequency for spanning from 48kHz to really Lo-Fi crunchy sound and full analogue dry/wet control. All effect parameter settings can be saved to the memory and instantly recalled with the effect, which makes Black Hole DSP II ideal for live performances.
Read more
 3 in stock $270.15
Cat: 717577 Rel: 31 Jan 19
 
Stereo mixer featuring 3 mono channel strips with level potentiometers - 14HP
Notes: Erica Synths Black Output is a high-quality output mixer and a stereo panner with balanced outputs and headphone amplifier for monitoring your modular masterpieces.

All inputs are buffered, we use stereo potentiometers (similar to those used in high quality studio mixers) for panning, IN4 is a stereo input with simultaneous level adjustment for both channels, IN3 has a CV controlled auto-pan function. There is also a 6.3mm jack for the balanced outputs and headphones.
Read more
 1 in stock $259.72
Cat: 690937 Rel: 25 Oct 18
 
Synth module for creating bass drum sounds - 14HP
Notes: Bass Drum is developed in collaboration with the French company e-licktronick and it's Erica Synths' take on analogue bass drum circuits adapted for modular systems. Massive, punchy sound, Accent & CV control over key parameters of the module make it distinctively expressive in live performances.
Read more
 2 in stock $249.29
Click for better price!
quote 690937
Cat: 712709 Rel: 10 Dec 18
 
Distinct topology digital/analogue cymbals module - 10HP
Notes: Erica Synths Cymbals is a distinct topology digital/analogue module, where cymbal samples are passed through AS3330 based VCA and controlled via envelope generators of unique design. The module features 10 sets of custom Crash and Ride cymbal samples with Tune control and individual Decay control. Accent and CV control over Tone and Decay allow you to create lot of variations in the Cymbals track. An extra feature is sample looping - when it's on, a certain part of the sample is looped while the envelope decay is on, thus creating a distinct, delay-like effect. Cymbal samples are developed by producer and musician Nero Bellum.
Read more
 2 in stock $239.18
Click for better price!
quote 712709
Cat: 690942 Rel: 19 Sep 18
 
Dual drive & distortion module with two independent distortion circuits 10 HP
Notes: For extreme, distorted drums Dual Drive module is a must! The module features two identical overdrive sections with adjustable Gain and Drive level, each with three flavours of overdrive.
CV control over Gain and Drive adds more expression, while built in limiter prevents output signal to run into undesired clipping.

Furthermore, the output of the first section is normaled to the input of the second, so you automatically get extreme, versatile dual overdrive circuit.
The module can be used in the stereo applications as well and it's not limited for drums only - it will turn any sound source into roaring monster.
Read more
 3 in stock $224.25
Click for better price!
quote 690942
Cat: 690947 Rel: 01 Nov 18
 
Two Spin FV-1 chips in one module, each filled with eight custom effect programs
Notes: To add some space to your compositions and nuances in sound design Erica Synths Dual FX module brings you two identical sections of 8 custom effects with two adjustable and CV controllable parameters.

Dual FX combines two Spin FV-1 chips in one module, each filled with eight custom effect programs with two adjustable and CV controlled parameters per effect and analogue dry/wet circuit. All parameter settings can be saved with the effect and recalled instantly during the performance. Also the output of the first FX section is normalised to the second input so creating huge layers of effects is easy.
Read more
 1 in stock $255.54
Cat: 690941 Rel: 06 Feb 19
 
Sample-based drum module with analogue VCA & decay envelope - 10HP
Notes: Hi-Hats D is Erica Synths take on classical digital hi-hats. Instead of using an integrated circuit DAC chip Hi-Hats D are using 6-bit discrete DAC for that unmistakable crunchy sound. For amplitude shaping samples are passed trough AS3330 based VCA and are controlled with an analogue envelope generator for versatile and snappy sound. Extra feature is Open Hi-Hat looping - when it's on, a certain part of the sample is looped while the envelope decay is on, thus creating distinct, delay-like effect.

Erica Synths Drum Sequencer has connectors for internal Trigger and Accent connections to Erica synths Drum modules. The connections are made via six wire ribbon cables with 2x3 connectors (similar to Eurorack PSU connectors), and you can save some patch cables if you have a lot of Erica Synths Drum modules. Internal connections will work only with Erica Synths modules and no other manufacturer module will support this functionality. If you have Erica Synths Drum Sequencer and other Erica Synths Drum modules and want to use internal connections, select "Hi-Hats D with internal connectors" option. If you do not want to use internal connections, select cheaper "Hi-Hats D without internal connectors" option.
Read more
 2 in stock $229.47
Click for better price!
quote 690941
Cat: 712706 Rel: 10 Jan 19
 
Drum modulator featuring two independent modulation/pitched noise sources
Notes: Erica Synths Modulator is an advanced modulation and pitched noise source with focus on rhythmic (but not limited to) compositions in mind. It features two identical syncable to the BPM LFOs/noise sources with selectable morphing waveshapes. LFO frequency can be manually adjustable, as well as they provide frequency divisions and multiplication in Sync mode. Each LFO has two outputs- main one and secondary one with adjustable phase, so you can create evolving modulations. Furthermore, LFOs can be linked to work at the same frequency and the first LFO has built in VCA to control output signal amplitude.
Read more
 3 in stock $206.52
Click for better price!
quote 712706
Cat: 690939 Rel: 25 Oct 18
 
Synth module for creating punchy tom sounds - 16HP
Notes: Toms is developed in collaboration with the French company e-licktronick and it's Erica Synths' take on analogue toms circuits adapted for modular systems. Massive, punchy sound, Accent and Tone CV make it distinctively expressive in studio and live performances.
Read more
 1 in stock $280.58
Cat: 739171 Rel: 18 Apr 19
 
B-STOCK: Box opened, product in perfect working order
Notes: ***B-STOCK: Box opened, product in perfect working order***


Performance oriented Sample Drum brings you two independent drum sounds or loops with plenty of manual and CV controlled parameters. Samples are stored on the microSD card, and OLED screen makes working with samples instant and easy.

Sample Drum allows you to slice up loops directly in your modular system and rearrange them to taste. For processing, there are tuning functions (including 1 v/octave pitch tracking) and virtual VCAs plus AD envelopes. Thanks to the module's dual-channel concept, two loops can be combined. It is also possible to load one-shot samples instead of entire rhythms, of course. A total of six CV inputs guarantees lively results.

Sample Drum is composed of two identical audio players. WAV files (including cue points) are fed to the module via a micro SD card. Loops can be cut into several sections using the Data, Start and End potentiometers. The resulting slices may be played back in any order imaginable. A tune control allows real-time pitch changes. Additionally, there is a virtual VCA plus AD envelope per slice. - But that's not all! There are three CV inputs per channel, which can be routed to any parameters. It is even possible to play sounds according to the 1 v / octave standard. Results are emitted via one output per player.
Read more
 1 in stock $296.04
Cat: 644210 Rel: 06 Apr 17
 
High density 8 channel utility module - 10HP
Notes: Levit8 is a high density utility module designed to give you a large number of attenuator/gain functions along with optional mix, invert, DC offset and polarity indication for incoming signals.

Few modules can beat the LEVIT8's high density of functions, which has eight channels that can be used as individual attenuators, amplifiers, inverters of offset generators. Optionally it features three different mix configurations with four or eight inputs for control voltages or audio signals, fulfilling various tasks at the same time.
Read more
 4 in stock $201.30
Click for better price!
quote 644210
Cat: 644211 Rel: 06 Apr 17
 
Expansion module for the Moog Mother-32 - 10HP
Notes: Mother's Little Helper is a companion module intended to be used with the Moog Mother32 semi-modular synthesizer. The MIDI out port allows CV/Gate control of Bank and Patch, changing the assign output, and allows turning on/off the MIDI controlled sustain ability of the Mother32. In addition, a Sample & Hold circuit has been added that is designed to be gate driven.
Read more
 2 in stock $206.53
Cat: 644208 Rel: 06 Apr 17
 
High density octal linear VCA module - 18HP
Notes: VC8 is a high density VCA module designed to give you a large number of VCAs with CV level and OFFSET control, along with optional VCA controlled dual sub-mix capability.

The VC8 combines eight high-class VCAs with linear characteristics in one module. Each channel offers a modulation input plus attenuator, a bipolar offset potentiometer and a level LED. Routing options enable the user to create sub-mixes of four channels.
Read more
 2 in stock $281.62
Cat: 690794 Rel: 30 May 18
 
Compact DSP-based multi-effect module - 10HP
Notes: The Flame FX16-CV module is a small low-cost DSP-based (Spin semiconductors FV-1, 24bit ADC/DAC) multi effect module, designed for small mobile Euro racks. 16 different multi-effect programs are available. There are three knobs with additional CV inputs to change the effect parameters. Also, it's possible to select the effect program with CV or pot.

Audio stereo input and stereo output levels are adjusted for modular rack levels. The input can be attenuated and is protected against level peaks. The dry/wet pot can be used manually for mixing between input and effect audio signal. The outputs are buffered by an op-amp. One red LED indicates clipping.

List of multi-effect programmes:

- PITCH/ECHO (Pitchshifter-Echo)
- REVERB PLATE TREMOLO (Reverb-Tremolo)
- VIBRATO (Reverb-Envelope Vibrato)
- FLANGER (Reverb-Flanger)
- CHORUS (Reverb-Chorus)
- PHASER (Reverb-Phaser)
- ECHO-REPEAT (Stereo Ping Pong Delay)
- AUTO-WAH (Reverb-Envelope Lowpass)
- RINGMODULATOR (Reverb-Ringmodulator stereo)
- BITCRUSHER (Reverb-Bitcrusher-Lowpass)
- REV-FL-LP (Reverb-Flanger-Lowpass)
- REV-HP-LP (Reverb-Highpass-Lowpass)
- REV-PT-LP (Reverb-Pitchshifter-Lowpass)
Read more
 1 in stock $209.65
Cat: 731213 Rel: 08 May 19
 
Quad VC/Envelope - 10HP
Notes: The FLAME "X-4" is a compact multifunctional 4x Envelope/VCA module, which combines in a very small space (10HP) 4 AR envelopes and 4 separate VCAs.

The module complements quad VCOs (eg the FLAME "4VOX") to control 4 VCAs per envelope generator in a small space.

Each channel can be used separately as an AR envelope generator with VCA, or even as a VCA.

There are 3 modes:

AR: 4 CV controllable separate Attack/Release envelopes on 4 VCA channels (per gate)
AD: 4 CV controllable separate Attack/Decay envelopes on 4 VCA channels (one shot per trigger)
VCA: 4 CV controllable separate VCAs

There is available a three-level switch for three different envelope rates from extremely short to long.

The envelope shape is set with the sliders (also adjustable via CV inputs).

In addition, the envelope can be looped (gated AD envelope loop).
Read more
 2 in stock $227.38
Click for better price!
quote 731213
Cat: 734840 Rel: 15 Jul 19
 
Analogue VCO focused on all aspects of modulation - 12HP
Notes: The OSC1 from Future Sound Systems presents a voltage-controlled analogue oscillator with a few features unexpected of a basic oscillator, with a particular focus on covering all bases of signal modulation. Once triangle, sinusoidal and pulse waveforms are derived from its sawtooth core, each waveform is passed through a VCA. The outputs from these VCAs are then summed at the Mix output, which can be switched between 2- and 4-quadrant-multiplication modes. These two QM modes allow for a plethora of amplitude modulation effects to be achieved. Level controls for each waveform dictate both static level, but also depth of modulation through careful design of the control summation. Each individual waveform output is taken pre-VCA for maximum patching flexibility.

Shape modulation of the triangular, sinusoidal and pulse waveforms is also available. Both the triangular and sinusoidal waveshapes can be skewed forward or backward into ramp-like shapes, whilst shaping the pulse wave gives standard pulsewidth modulation.

Frequency modulation is available in both Linear and Exponential modes. The OSC1 also tracks to 1V/Octave over four octaves in its audible (HF) range, but can also be used as a low frequency oscillator in LF mode.

A Sync input allows for the OSC1 to be reset by an external signal. A rising edge will reset the sawtooth wave to its peak, from which it descends. The Inject input, meanwhile, allows for external signals to interfere with the sawtooth core. This allows for intermodulation-type effects to be produced, and opens new realms of chaotic oscillations.
Read more
 2 in stock $248.24
FORTHCOMING
Grayscale Permutation 12HP Random Sequencer Module (black panel version, random sequencer based on the Turing Machine)
Cat: 739133 Rel: 22 Jul 19
 
Random looping sequencer - black faceplate, 12HP
Notes: Permutation is a set of random sequencers that use a digital shift register to generate unpredictable CV and gate patterns that can be locked into repeating loops. The concept is based on the Turing Machine, an open source module designed by Tom Whitwell.

Permutation retains the core functionality of the Turing Machine while adding new features such as dedicated outputs for each bit of the shift register, CV inputs for all parameters, and an internal bipolar VCA. Locked sequences are also saved across power cycles.
Read more
coming soon $245.11
FORTHCOMING
Grayscale Permutation 12HP Random Sequencer Module (grey panel version, random sequencer based on the Turing Machine)
Cat: 739134 Rel: 22 Jul 19
 
Random looping sequencer - grey faceplate, 12HP
Notes: Permutation is a set of random sequencers that use a digital shift register to generate unpredictable CV and gate patterns that can be locked into repeating loops. The concept is based on the Turing Machine, an open source module designed by Tom Whitwell.

Permutation retains the core functionality of the Turing Machine while adding new features such as dedicated outputs for each bit of the shift register, CV inputs for all parameters, and an internal bipolar VCA. Locked sequences are also saved across power cycles.
Read more
coming soon $245.11
FORTHCOMING
Grayscale Permutation 18HP Random Sequencer Module (black panel version, random sequencer based on the Turing Machine)
Cat: 739131 Rel: 22 Jul 19
 
Random looping sequencer - black faceplate, 18HP
Notes: Permutation is a set of random sequencers that use a digital shift register to generate unpredictable CV and gate patterns that can be locked into repeating loops. The concept is based on the Turing Machine, an open source module designed by Tom Whitwell.

Permutation retains the core functionality of the Turing Machine while adding new features such as dedicated outputs for each bit of the shift register, CV inputs for all parameters, and an internal bipolar VCA. Locked sequences are also saved across power cycles.
Read more
coming soon $295.18
FORTHCOMING
Grayscale Permutation 18HP Random Sequencer Module (grey panel version, random sequencer based on the Turing Machine)
Cat: 739132 Rel: 22 Jul 19
 
Random looping sequencer - grey faceplate, 18HP
Notes: Permutation is a set of random sequencers that use a digital shift register to generate unpredictable CV and gate patterns that can be locked into repeating loops. The concept is based on the Turing Machine, an open source module designed by Tom Whitwell.

Permutation retains the core functionality of the Turing Machine while adding new features such as dedicated outputs for each bit of the shift register, CV inputs for all parameters, and an internal bipolar VCA. Locked sequences are also saved across power cycles.
Read more
coming soon $295.18
Cat: 655315 Rel: 31 Jul 17
 
Analog bassdrum synthesis with sub-oscillator - 13HP
Notes: Not just another clone or continuation of the 808-esque, acid-style kicks of the Mutant Bassdrum - the Mutant BD9 seeks to explore uncharted bassdrum territory by having an integrated sub-oscillator for maximal auditory obliteration.

Parametric bassdrum synthesis offers creative control of the core sound:
- The primary analog VCO offers classic 909-esque sinusoidal bassdrums, but can also be switched to generate a square wave bassdrum
- The PITCH of the VCO spans several octaves, from about 30Hz to 240Hz, and can be modulated with voltage control
- A novel PITCH DECAY circuit allows you to adjust the duration and AMOUNT of the pitch-modulation envelope applied to the bassdrum, from short blips to exaggerated tom-like sweeps
- The AMPLITUDE DECAY allows adjustment of the length of the bassdrum, from short punchy kicks to massive booms. This parameter is voltage-controlled with a snappy CV response time, allowing you to modulate the duration of your kicks per step.
- The CLICK generator is responsible for the attack intensity of the BD9. A fair amount of circuitry goes into creating this subtle punch at the beginning of the kick. The level of this effect is adjustable up to a fairly dramatic extremity.
- The overall timbre of the BD9 varies with the DRIVE control from warm, analog bassdrums at low settings to speaker-shattering overdriven sounds at high settings. Output levels are modular-level signals, unlike many classic line-level percussive devices.

Still not heavy enough? Try the sub-oscillator:
- A square wave sub-oscillator derived from the primary oscillator's pitch can be mixed in (manually and with voltage control) to the BD9. The effect can be subtle deepness or extreme timbre changes.
- A jumper on the back of the module allows you to select between the sub-osc being a raw square wave or having some of the high frequency components removed with a lowpass filter.
- At high OUTPUT DRIVE and SUB LVL combinations, the sub-oscillator can be modulated with CV to saturate the BD9 output in evolving ways.
- The SUB OCT can be set to 0, -1 or -2 octaves down from the primary oscillator. A drop of 0 means that you can mix an equal-pitch square wave with a sinusoidal primary wave.

Designed for the contemporary modular synthesizer:
- Plenty of Eurorack-compatible control voltage inputs with bipolar attenuverters allow synthesis of dynamic percussion
- A practical analog trigger circuit allows activation of the BD9 from many signal sources (anything with a positive-going edge lasting 2ms or longer). Most electronic drum pads can also directly trigger the Mutant BD9.
- An accent input accepts analog voltage control (0 to 5V will fully modulate the volume from low to high)
Read more
 1 in stock $224.25
Cat: 677171 Rel: 31 Jul 17
 
B-STOCK: Box opened, product in perfect working order
Notes: ***B-STOCK: Box opened, product in perfect working order***


Not just another clone or continuation of the 808-esque, acid-style kicks of the Mutant Bassdrum - the Mutant BD9 seeks to explore uncharted bassdrum territory by having an integrated sub-oscillator for maximal auditory obliteration.

Parametric bassdrum synthesis offers creative control of the core sound:
- The primary analog VCO offers classic 909-esque sinusoidal bassdrums, but can also be switched to generate a square wave bassdrum
- The PITCH of the VCO spans several octaves, from about 30Hz to 240Hz, and can be modulated with voltage control
- A novel PITCH DECAY circuit allows you to adjust the duration and AMOUNT of the pitch-modulation envelope applied to the bassdrum, from short blips to exaggerated tom-like sweeps
- The AMPLITUDE DECAY allows adjustment of the length of the bassdrum, from short punchy kicks to massive booms. This parameter is voltage-controlled with a snappy CV response time, allowing you to modulate the duration of your kicks per step.
- The CLICK generator is responsible for the attack intensity of the BD9. A fair amount of circuitry goes into creating this subtle punch at the beginning of the kick. The level of this effect is adjustable up to a fairly dramatic extremity.
- The overall timbre of the BD9 varies with the DRIVE control from warm, analog bassdrums at low settings to speaker-shattering overdriven sounds at high settings. Output levels are modular-level signals, unlike many classic line-level percussive devices.

Still not heavy enough? Try the sub-oscillator:
- A square wave sub-oscillator derived from the primary oscillator's pitch can be mixed in (manually and with voltage control) to the BD9. The effect can be subtle deepness or extreme timbre changes.
- A jumper on the back of the module allows you to select between the sub-osc being a raw square wave or having some of the high frequency components removed with a lowpass filter.
- At high OUTPUT DRIVE and SUB LVL combinations, the sub-oscillator can be modulated with CV to saturate the BD9 output in evolving ways.
- The SUB OCT can be set to 0, -1 or -2 octaves down from the primary oscillator. A drop of 0 means that you can mix an equal-pitch square wave with a sinusoidal primary wave.

Designed for the contemporary modular synthesizer:
- Plenty of Eurorack-compatible control voltage inputs with bipolar attenuverters allow synthesis of dynamic percussion
- A practical analog trigger circuit allows activation of the BD9 from many signal sources (anything with a positive-going edge lasting 2ms or longer). Most electronic drum pads can also directly trigger the Mutant BD9.
- An accent input accepts analog voltage control (0 to 5V will fully modulate the volume from low to high)
Read more
 1 in stock $220.09
Cat: 655335 Rel: 31 Jul 17
 
Powerful dual hi-hat generator module - 13HP
Notes: A classic electro percussion synthesis design reborn as something completely different. Hexinverter wanted to recreate a classic hihat synthesis design as something new and exciting, so they took the super electro 808 circuit and transformed it into a powerful creative tool for modular synthesis!

Featuring:

- Analogue hihat circuitry capable of synthesising vanilla TR-808 open and closed hihat sounds (simultaneously)
- External audio input lets you synthesise hihats from virtually any sound source (Jupiter Storm, vcNOIZ, etc.)
- Lo-fidelity original VCAs replaced by OTA-based modern VCAs
- VCA DRIVE control for each hihat allows you to dial in anything from soft metallic hihats to extremely overdriven, crunchy hihats
- Exclusive switch lets you select how the two hihats (open/closed) interact with each other when triggered at the same time
- Cutoff frequency control for internal resonant bandpass filter
- Resonant filter can be switched on/off
- Modular level mutual accent input (0-5V CV)
- Trigger input accepts almost anything as a trigger signal
- Non-invasive analogue optocouplers used for voltage control, thus, completely vintage sounds can still be had if that's what you're after!
- Completely redesigned, hi-fi signal chain spares no expense by replacing cheap transistor amplifiers with low noise op-amp and OTA equivalents
- You can dial in super hot, modular level output levels (up to 20Vp-p!)
Read more
 1 in stock $208.61
Cat: 655329 Rel: 31 Jul 17
 
Analog snare drum synthesis with external input - 13HP
Notes: From classic electro snares to warping, alien percussion, the Mutant Snare is a radical departure from the static sounds of the 808!

MIX and DRIVE:
- MIX lets you blend between the SHELL and SNAPPY tones that make up the overall snare drum
- Turn up the DRIVE to get overdriven snare tones with intense harmonics. The purple LED indicates when the snare begins to overdrive
- Like the other Mutant Drums, signal levels have been normalized for modular level input and output (up to 20Vpp)

SHELL synthesizes the drum skins:
- Analog bridged-t sinewave oscillators, for those organic-sounding tones we've come to love from the 808
- TONE control blends between the two sinewaves of different frequency
- SHELL PITCH lets you tune one of the sine waves, to change the pitch of your snare drum

SNAPPY adds some noise to the snare:
- An analog white noise generator feeds the SNAPPY circuit
- An external input lets you patch any sound source you like into the SNAPPY generator
- Voltage control of SNAPPY decay
- SNAPPY feeds into an analog selectable high-pass or band-pass filter
- Voltage control of filter cutoff frequency
- When nothing is plugged into the cutoff CV input, the SNAPPY envelope OR the adjustable sinewave from the SHELL generator normalize through the CV attenuverter for cutoff CV. A jumper on the back of the module allows you to select which of these internal modulation signals are routed here
- Filter has three resonance settings: classic 808 (low resonance), high resonance, and self oscillation
- Bipolar attenuators (aka: 'attenuverters') on CV inputs
Read more
 1 in stock $224.25
Cat: 602195 Rel: 10 Aug 16
 
Full featured VCO/LFO synth module - 8HP wide
Notes: Full-featured triangle core VCO/LFO

The Dixie II+ is a larger variant of the classic Dixie II. Using the same great triangle core oscillator, it adds a number of features to make it even more versatile with only a modest increase in size. The Dixie II+ makes a great primary oscillator for a modular system, or a great companion the Rubicon.
Read more
 2 in stock $202.35
Cat: 563579 Rel: 10 Mar 15
 
Dual slider based ADSR envelope synth module, 14HP wide
Notes: The circuit is based in part on the Roland SH-101 / System100m design with several enhancements.
Read more
 4 in stock $202.35
Artikel 1 bis 50 von 135 auf Seite 1 von 3 anzeigen
1  2  3  »

Filter

Synth modules
DJ-Ausrüstung
Release Date
Close