100% Sicheres Einkaufen

Studio equipment

Our full range of studio equipment from all the leading equipment and software brands. Guaranteed fast delivery and low prices.

Visit Juno Studio

100% Sicheres Einkaufen

DJ equipment

Our full range of DJ equipment from all the leading equipment and software brands. Guaranteed fast delivery and low prices.Visit Juno DJ

Synth modules

Startseite  Equipment  

Synth modules

Options
Artikel 1 bis 4 von 4 auf Seite 1 von 1 anzeigen
Subscribe to our weekly Studio Equipment emails
FORTHCOMING
ADDAC System ADDAC806 Bluetooth Audio Module (red faceplate)
Notes: This small module will allow you to send wireless audio signals from any bluetooth compatible device straight to your modular.

Mechanical:
. Format: Eurorack
. Width: 4 HP
. Depth: 4.5 cm

Electrical:
. Max current: 75mA on each rail
. Bus Board Cable: 8 × 2 IDC (Doepfer style) connector
Read more
coming soon TBA
FORTHCOMING
Doepfer A-174-4 3D Joystick Module
Cat: 765892 Rel: 31 Jul 20
 
control voltage module
Notes: Module A-174-4 modules outputs three control voltages generated by a spring-loaded X/Y cross potentiometer (so-called joy stick) and a Gate signal. The control voltages for X and Y are controlled by the X and Y position of the joystick in the usual way. The third control voltage Z is controlled by the rotation of the spring-loaded joystick knob. The Gate signal is generated by a button at the center/top of the joystick knob.

For each control voltage the non-inverted signal (X, Y, Z) as well as the inverted signal with adjustable offset (-X+XO, -Y+YO, -Z+ZO) are available. The generic joystick control voltages are bipolar, i.e. they range from typ. -5V (lowest position) via 0V (center position) to typ. +5V (highest position). The "Overlap" switches can be used to add a fixed offset voltage of typ. +5V to the non-inverting output in question so that the output voltage range changes to typ. 0...+10V (rather than -5...+5V). That's necessary if e.g. a VCA has to be controlled, which requires a pure positive control voltage range. The switches are named "overlap" because they allow the overlapping of the non-inverting CV output (X, Y, Z) with the inverting output (-X+XO, -Y+YO, -Z+ZO) for crossfading applications. With the overlap switch "on" and appropriate setting of the offset control it's possible to obtain a control voltage range of 0...+10V for the non-inverting output and +10V...0V (i.e. same range but opposite direction) for the inverting output.

The offset voltages which are added to the inverting outputs can be adjusted by means of three small potentiometers. That way different kinds of control voltage ranges are possible, e.g.
-5V ... +5V for the non-inverting output and +5V ... -5V for the inverting output ( Overlap = off, Offset = 0)
0 ... +10V for the non-inverting output and +10V ... 0V for the inverting output ( Overlap = on, Offset = max)
-5V ... +5V for the non-inverting output and +10V ... 0V for the inverting output ( Overlap = off, Offset = max)
0 ... +10V for the non-inverting output and +5V ... -5V for the inverting output ( Overlap = on, Offset = 0)
On top of this the four quadrant voltages Q1, Q2, Q3 and Q4 are available. A quadrant voltage becomes positive when the joystick is positioned in the quadrant in question.
Each CV output is equipped with an LED that displays the present voltage.

Because of the construction height of the joystick (about 7 cm) the module cannot be installed into the cases A-100P6, A-100P9, A-100PMS6, A-100PMS9 and A-100PMS12 during transportation as the depth of the case cover is not sufficient. Into the base cases A-100PB and A-100PMB as well as in all other cases without cover the module can be installed without problems.

HP : 12
Read more
coming soon TBA
FORTHCOMING
EMW X-Drum 12-Bit Drum Module (black faceplate)
coming soon TBA
FORTHCOMING
Noise Engineering Desmodus Versio dsp Reverb & FX Platform Module
coming soon TBA
Artikel 1 bis 4 von 4 auf Seite 1 von 1 anzeigen

Filter

Synth modules
DJ-Ausrüstung
Release Date
Featured
Close