Synth Module Accessories

Notes: Low-cost, portable, compact enclosure that turns Eurorack modules into table-top instruments.

The Pod20 is 20HP with 1.34" (34mm) of available module depth. The built-in power supply has two power connectors and can be daisy-chained to other Pods. More power connectors can be added with the Multi Power Cable accessory.

Pods require a power brick. If you already have a powered Pod and power brick (or a Row Power module) you can use a barrel cable to daisy-chain powered Pods.

The Pod20 includes ten (10) M3x8mm stainless steel screws and is compatible with M3 Knurlies.

Notes: Low-cost, portable, compact enclosure that turns Eurorack modules into table-top instruments.

The Pod26 is 26HP with 1.34" (34mm) of available module depth. The built-in power supply has two power connectors and can be daisy-chained to other Pods. More power connectors can be added with the Multi Power Cable accessory.

Pods require a power brick. If you already have a powered Pod and power brick (or a Row Power module) you can use a barrel cable to daisy-chain powered Pods.

The Pod26 includes ten (10) M3x8mm stainless steel screws and is compatible with M3 Knurlies.

Notes: Low-cost, portable, compact enclosure that turns Eurorack modules into table-top instruments.

The Pod32 is 32HP with 1.34" (34mm) of available module depth. The built-in power supply has two power connectors and can be daisy-chained to other Pods. More power connectors can be added with the Multi Power Cable accessory.

Pods require a power brick. If you already have a powered Pod and power brick (or a Row Power module) you can use a barrel cable to daisy-chain powered Pods.

The Pod32 includes ten (10) M3x8mm stainless steel screws and is compatible with M3 Knurlies.

Notes: Low-cost, portable, compact enclosure that turns Eurorack modules into table-top instruments.

The Pod34X is 34HP wide and has extra room to fit even the deepest modules (2.16" / 55mm of available module depth). The built-in power supply has four power connectors and can be daisy-chained to other Pods. More power connectors can be added with the Multi Power Cable accessory.

This Pod requires a power brick (not included).

Or, if you already have a Pod and power brick (or a Row Power module) you can use a barrel cable to daisy-chain power supplies.

Pods are a perfect way to get started in Eurorack, or add a couple more modules to your monster system!

Made from 100% anodized aluminum, Pods are light, tough and perfect for on-the-go set ups. The power supply can handle up to 1.4A of +12V, which is plenty of juice for even the most modern digital modules. (Or if you prefer to DIY your power supply, Pods are also available unpowered)

Each Pod typically will house one or two modules, but three or more can be accommodated using a multi-power cable accessory.

Mix and match your Pods with desktop synths, effect pedals, drum machines or any musical gear for a flexible modular system. Pods can even daisy- chain with the 4ms Row Power system making them a convenient outboard mini-skiff. Need to add another module? Just add a Pod! Need to pack light for a live set? Just grab the Pods you need and go!

Basic Features:

34 HP Eurorack modular space
Standard M3 threaded holes
100% lightweight anodized aluminum
Built-in Power supply
Red, White, and Blue LED power indicators

Includes:
34HP Pod, black anodized aluminum
Extra deep (2.16"/55mm) fits virtually every Eurorack module
Built-in power supply with four Eurorack power headers
M3 x 8mm pan-head screws, stainless steel (10)
Adhesive rubber feet (4)
Does not include barrel cable or power brick
Power Supply:
Four 16-pin Eurorack power shrouded headers
+12V max 1.4A
-12V max 0.65A
+5V max 1.0A
Power input: Two barrel jacks for daisy-chaining
15V-20VDC, 2.1mm positive tip
Exterior dimensions:
Width: 177.3mm (6.98")
Height: 159.5mm (6.28")
Depth: 57mm (2.24")
Interior dimensions:
Max module depth: 55mm (2.16")
Module width: 34HP
Weight:
0.3 kg = 10 oz

Notes: The Pod40X is 40HP with 2.00" (51mm) of available module depth. The built-in power supply has four power connectors and can be daisy-chained to other Pods. More power connectors can be added with the Multi Power Cable accessory.

Pods require a power brick. If you already have a powered Pod and power brick (or a Row Power module) you can use a barrel cable to daisy-chain powered Pods.

The Pod40 includes ten (10) M3x8mm stainless steel screws and is compatible with M3 Knurlies.

Notes: Excalibus is an affordable, skiff friendly powerful power supply (1.2A per rail) and bus. It provides the best of all worlds, power, stability, small size and price. Specially designed for two rows systems with mid to high power consumption. DIY friendly and safe, as it works with any standard DC supply.

Measurements: 50mm x 400mm x 12mm

Notes: Desktop enclosure case for the Empress Zoia Euroboro- 12v power supply included. Euroboro not included- picture shown for demonstration purposes only.

Notes: The Mini Case offers 40 HP for mounting modules. A power supply is built-in.

208 mm long x 45mm deep.

PLEASE NOTE: Comes with EU 2 pin plug only - UK adapter may be required.

Notes: ***B-STOCK: Without original box, product in perfect working order***


Desktop Eurorack moduile case 3U - 84HP with power supply on the left side.

Plexiglas side panels 5mm thick.

Aluminium chassis.

6cm deep, but only 4cm deep all along the 5HP of the power supply. Check your modules before!

Tech specs:
- Width : 84HP
- Depth : 6cm
- Depth all along the 5HP of the power supply : 4cm
- Current Consumption : +12V : 2.4A ; -12V : 1.2A ; +5V : 0.5A

Notes: ***B-STOCK: Box opened, product in perfect working order***


Small desktop enclosure for Eurorack modules with 42 HP space and a maximum depth of 32mm. A relatively strong power solution with an external power supply and an on/off switch located at the case is included.

The power supply provides:

- 850 mA at +12V
- 850mA at -12V
- 500mA at +5V

The power distribution has 14 connectors and the case can house exactly fourteen modules from Erica's Pico Series.

Notes: ***B-STOCK: Box opened, product in perfect working order***


Small desktop enclosure for Eurorack modules with 42 HP space and a maximum depth of 32mm. A relatively strong power solution with an external power supply and an on/off switch located at the case is included.

The power supply provides:

- 850 mA at +12V
- 850mA at -12V
- 500mA at +5V

The power distribution has 14 connectors and the case can house exactly fourteen modules from Erica's Pico Series.

Notes: A new and improved design with additional space and comfort for longer journeys!

This backpack is a must-have accessory for our 2x104HP aluminum and carbon travel cases.

Featuring a roomy main compartment with an elastic band for securing a laptop in place, spacious side pockets, and a separate zipped compartment on the back, there's plenty of room for all your patch cables and other accessories.

Dimensions: 58 x 18 x 32 cm

Notes: The Clockable LFO brings multiple waveforms, CV control, subdivisions, and wave symmetry in a simple, user friendly package. LFO speed can be controlled by the tap tempo pushbutton, clock input, or over-sized Speed knob. There are three waveforms that can be selected by toggle and further modified by the Level and Symmetry knob. The Symmetry knob shifts the wave form from a symmetrical wave to a ramp up or ramp down waveform (or when using square wave, acts a pulse width control). Clock In and Clock Out for syncing with other devices. All knobs on the Clockable LFO can be manipulated with CV. As with all Hungry Robot "Modular Boxes" the Clockable LFO can be powered with a simple 9V DC, Negative Center power supply.

KNOBS
-SPEED: Sets the overall speed of the LFO. Turning this knob will override any tap or clocked tempo. This control is still affected by subdivision.
-LEVEL: Sets the level of the LFO output. Ranges from 0-10V peak-to-peak
-SYMMETRY: Sets the symmetry of the waveform. Shifting from ramp-down to ramp-up on triangle and sin waves. Adjusts pulse width on square.

SWITCHES
-SUBDIVISIONS: Selects subdivisions (x1,x2,#2). Automatically converts LFO speed.
-WAVESHAPE: Selects the waveshape of the LFO output (Sin, Triangle, Square)

PATCH POINTS
-SPD CV: CV input for Speed. Allows for CV control of this parameter.
-SYM CV: CV input for Symmetry. Allows for CV control of this parameter.
-LVL CV: CV input for Level. Allows for CV control of this parameter.
-CLK IN: Will sync to external clock. Will override the speed knob.
-CLK OUT: Outputs a 5V clock signal at 50% duty cycle. Can also be useful as a gate signal for your ADSR
-LFO OUT: Two outputs of final waveform. Both outputs are buffered for minimal signal attenuation. 10V Peak-to-Peak

PUSHBUTTON
-CENTER PUSHBUTTON: On-board tap tempo. Will override the speed knob.

Dimensions: 4.7" x 3.7" x 1.96"
Power: 9V DC - Negative Center - 2.1mm Barrel

Notes: The Hungry Robot CV Keys is the perfect utility for incorporating 1V/OCT, chromatic semitones into a modular system when it is not convenient to use midi keyboards or a midi-to-CV interface. This small pushbutton keyboard has just enough functionality for most modular users and provides very accurate 1V/OCT tracking. The CV keys has a full octave keyboard as well as octave switch allowing you to jump between octaves on the fly. The Hold button latches the gate signal for handsfree use. It uses last note priority, has two unique gate modes, two buffered outputs, and a Transpose jack that let you patch in an external sequence and transpose it chromatically through the CV keys.

KNOBS
-OCTAVE: Cycles between 6 octaves

PUSHBUTTONS
-HOLD: When LED is lit, Hold is on. When Hold Mode is on, the Gate and Retriggered Gate will latch so you don't have to hold down the key
-KEYS: 13 note, single octave keyboard. Last note priority

PATCH POINTS
-TRANSPOSE: Patching in a control voltage (i.e. from a sequencer) allows you to transpose the sequence according to the notes you play
-GATE: Standard 5V gate outputted when a key is played or when Hold mode is active
-GATE (Retriggered): 5V gate that retriggers with every new note played. NOTE: To retrigger an ADSR, you must use a short release setting
-CV OUT: Two buffered 1V/OCT outputs to patch to your multiple VCOs

Dimensions: 4.7" x 3.7" x 1.96"
Power: 9V DC - Negative Center - 2.1mm Barrel

Notes: The Hungry Robot VCO is an all-analog, low cost, workhorse of a VCO. It can output triangle, sawtooth, and square waveforms simultaneously with tremendous bass response. The VCO has exceptional 1V/OCT tracking with FM modulation. The FM modulation input has a built-in CV attenuator as well as an inversion switch. The square wave has PWM with a built-in CV attenuator. As with all Hungry Robot "Modular Boxes" the VCO can be powered with a simple 9V DC, Negative Center power supply.

KNOBS
-COARSE: Provides a wide sweep of output frequencies
-FINE: Provides a narrow sweep of output frequencies for fine tuning
-PWM: Attenuator for the PWM CV input.
-FM: Attenuator for the FM CV input

SWITCHES
-INVERT: Inverts the incoming FM CV input. Toggle to the right to invert incoming CV

PATCH POINTS
-1V/OCT: Input for 1V/OCT tracking
-FM: CV input for Frequency Modulation
-PWM: CV input for Pulse Width Modulation
-TRIANGLE: Triangle waveform output
-SAWTOOTH: Sawtooth waveform output
-SQUARE: Square waveform output

Dimensions: 4.7" x 2.6" x 1.5"
Power: 9V DC - Negative Center - 2.1mm Barrel

Notes: 7U x 104HP Gig Bag

Sized to perfectly fit the 7U x 104HP Performance Cases.

The padded main compartment protects your case from bumps and scratches

Waterproof zippers

Outer pocket for stuffing accessories and other gear (great for adding the Intellijel Pouch filled with cables and hubs)

The rear pocket closes with velcro at top but unzips at the bottom to become a handle sheath so your case can sit on top of a rolling suitcase.

Rugged strap connectors with clipped strap

Carry handles

Lightweight

Notes: 7U x 84HP Gig Bag

Sized to perfectly fit the 7U x 84HP Performance Cases.

The padded main compartment protects your case from bumps and scratches

Waterproof zippers

Outer pocket for stuffing accessories and other gear (great for adding the Intellijel Pouch filled with cables and hubs)

The rear pocket closes with velcro at top but unzips at the bottom to become a handle sheath so your case can sit on top of a rolling suitcase.

Rugged strap connectors with clipped strap

Carry handles

Lightweight

Notes: Loci Bundl3

Perfect expansion or starter pack containing Classic, Dinky and Expander stands
Assembled in seconds
Multiple configurations for a number of layout options up to 3 tiers!
Super strong.
Precision laser cut from 6mm oak veneer
Non-slip pads
Packs flat to slide in your case.

Notes: Loci Tripl3

A Tripl3 is a combination of a Classic and Doubl2 stands allowing 3 angled tiers
Can be used as separates, flipper over for other options or combined with additional stands.
Assembled in seconds
Super strong
Precision laser cut from 6mm oak veneer
Non-slip bands
Packs flat to slide in your case.

Notes: In 2009 Tony designed the first Skiff to complement the vertically oriented cases available at the time by providing an ergonomic enclosure for our Rene and Pressure Points touch controllers.

Today the Make Noise Skiff is updated to provide a smart way to build a small modular synthesizer. It is low cost, but extremely durable. The clean simple lines and matte black color place visual emphasis where the action is; the patch the artist has created.

Notes: ***B-STOCK: Box opened, product in perfect working order***


Introducing the special edition Pod20 customized for ModBap Modular by 4ms, the Modbap20.

The Modbap20 Powered Eurorack Case can be your on-ramp to eurorack, a great option for a focused mini system, or a live control surface, or the perfect way to expand a larger system. The Modbap20 is 20HP in width, and 34mm deep with 4ms power bus boards. The included power brick and your favorite combination of up to 20HP modules are all you need to get started with your new mini system, control pod, performance pod, effects pod, or whatever you so desire.

Features

20HP wide, 34mm deep powered Eurorack case
power brick (included)
Available power: 0.7A (+12V), 0.28A (-12V), 0.2A (+5V)
Rugged anodized aluminum construction

Notes: This is an extruded aluminum Eurorack case with wood sides (no modules included). Up to 1.9" module depth. Requires separate Eurorack power module for use.

Includes sliding nuts and screws.

Notes: Introducing the n-1 case, a sleek, thoughtfully designed Eurorack modular case for sound and music makers. Our flat-packable case interlocks and slides together, requiring no tools to assemble. Later in the year, we will be launching a range of accessories that will provide further versatility to the n-1 case. These add-ons will allow you to customize your case to suit your unique preferences, ensuring it remains an adaptable companion on your evolving musical journey.

What's in the box?
12mm plywood frame
3mm plywood back
4 dowel pins
1 pair of aluminum rails
M5 hex socket screws
M3 rail slide nuts
mystery stickers!
*case is unpowered, giving users the freedom to choose a panel-mounted power supply or adapt an internal power option.

Notes: EcoSynth is a small, portable Eurorack modular case solution, designed for your desktop! It's a practical solution designed to save your hard-earned cash for modules. If you're looking for a small desktop solution to augment other desktop electronic hardware, this is for you. If you need a larger case, EcoSkiff passes on the savings for more traditional size racks like 84HP and 104HP.

Save on money and space: get just as much HP as you need!

Available in the following sizes:
24HP
44HP
64HP
84HP
104HP

Features and specifications:

Over-current protection: shuts off each power rail automatically if modules use too much current on that rail
The skiff goes together with just a Phillips head screwdriver!
Comes with 3mm slide nuts
Max module depth: 44mm
Max module depth above power supply: 33mm

Specifications, 24HP-44HP:
Power output:
+12V @ 1A
-12V @300mA
5V@ 150mA
Power connectors: 2 (plus optional flying bus cable)

Specifications, 64HP-104HP:
Power output:
+12V @ 2A
-12V @750mA
5V@ 1.5A
Power connectors: 15
Daisy chains to another EcoSkiff, Skiff Power, Five Amp Power, or Schottkey DC

Requires a 12V 5A center positive power brick with a 5.5mm x 2.1mm tip.
Assembly required, but no soldering needed.

Notes: EcoSynth is a small, portable Eurorack modular case solution, designed for your desktop! It's a practical solution designed to save your hard-earned cash for modules. If you're looking for a small desktop solution to augment other desktop electronic hardware, this is for you. If you need a larger case, EcoSkiff passes on the savings for more traditional size racks like 84HP and 104HP.

Save on money and space: get just as much HP as you need!

Available in the following sizes:
24HP
44HP
64HP
84HP
104HP

Features and specifications:

Over-current protection: shuts off each power rail automatically if modules use too much current on that rail
The skiff goes together with just a Phillips head screwdriver!
Comes with 3mm slide nuts
Max module depth: 44mm
Max module depth above power supply: 33mm

Specifications, 24HP-44HP:

Power output:
+12V @ 1A
-12V @300mA
5V@ 150mA
Power connectors: 2 (plus optional flying bus cable)

Requires a 12V 5A center positive power brick with a 5.5mm x 2.1mm tip.
Assembly required, but no soldering needed.

Notes: EcoSynth is a small, portable Eurorack modular case solution, designed for your desktop! It's a practical solution designed to save your hard-earned cash for modules. If you're looking for a small desktop solution to augment other desktop electronic hardware, this is for you. If you need a larger case, EcoSkiff passes on the savings for more traditional size racks like 84HP and 104HP.

Save on money and space: get just as much HP as you need!

Available in the following sizes:
24HP
44HP
64HP
84HP
104HP

Features and specifications:

Over-current protection: shuts off each power rail automatically if modules use too much current on that rail
The skiff goes together with just a Phillips head screwdriver!
Comes with 3mm slide nuts
Max module depth: 44mm
Max module depth above power supply: 33mm

Specifications, 24HP-44HP:
Power output:
+12V @ 1A
-12V @300mA
5V@ 150mA
Power connectors: 2 (plus optional flying bus cable)

Specifications, 64HP-104HP:
Power output:
+12V @ 2A
-12V @750mA
5V@ 1.5A
Power connectors: 15
Daisy chains to another EcoSkiff, Skiff Power, Five Amp Power, or Schottkey DC

Requires a 12V 5A center positive power brick with a 5.5mm x 2.1mm tip.
Assembly required, but no soldering needed.

Notes: EcoSynth is a small, portable Eurorack modular case solution, designed for your desktop! It's a practical solution designed to save your hard-earned cash for modules. If you're looking for a small desktop solution to augment other desktop electronic hardware, this is for you. If you need a larger case, EcoSkiff passes on the savings for more traditional size racks like 84HP and 104HP.

Save on money and space: get just as much HP as you need!

Available in the following sizes:
24HP
44HP
64HP
84HP
104HP

Features and specifications:

Over-current protection: shuts off each power rail automatically if modules use too much current on that rail
The skiff goes together with just a Phillips head screwdriver!
Comes with 3mm slide nuts
Max module depth: 44mm
Max module depth above power supply: 33mm

Specifications, 24HP-44HP:
Power output:
+12V @ 1A
-12V @300mA
5V@ 150mA
Power connectors: 2 (plus optional flying bus cable)

Specifications, 64HP-104HP:
Power output:
+12V @ 2A
-12V @750mA
5V@ 1.5A
Power connectors: 15
Daisy chains to another EcoSkiff, Skiff Power, Five Amp Power, or Schottkey DC

Requires a 12V 5A center positive power brick with a 5.5mm x 2.1mm tip.
Assembly required, but no soldering needed.

Notes: The Happy Ending Kit is an easy way to get everything needed to start a Eurorack modular system.

The Happy Ending Kit includes:
1 x Z-Rails set plus screws to attach to Z-Ears
1 x uZeus 4HP PSU with 2 x flying bus boards
1 x UK 3-pin mains adapter

Notes: The Happy Ending Kit is an easy way to get everything needed to start a Eurorack modular system.

The Happy Ending Kit includes:
1 x Z-Rails set plus screws to attach to Z-Ears
1 x uZeus 4HP PSU with 2 x flying bus boards
1 x UK 3-pin mains adapter

Notes: The tiny but mighty Eurorack power supply. Winterbloom's love letter to DIYers is perfect for custom cases.

Micronova is a miniature 100x30mm power supply with a big soul. It can provide up to 18W of power for your modules and multiple units can be easily daisy chained to power larger systems.

Despite being adorably small, Micronova provides lots of flexibility for custom case builds. It can be powered through an attached DC barrel jack, screw terminals, or through an optional front entry panel.

Micronova is equipped with two Eurorack power headers that can be expanded using a busboard or flying bus cable.

Micronova also has critical safety features including reverse polarity protection, a resettable polyfuse, and over-current shutdown.

A suitable AC-DC power adapter is required.

A tiny 100mm x 30mm board with M3 mounting holes
Provides +12V @ 1A, -12V @ 300mA, and +5V @ 500mA
Includes two 16-pin Eurorack power headers
Requires a 15V to 20V center positive DC power supply
Multiple units can be daisy chained
Reverse-polarity, over-current, and over-temperature protection