Synth Module Accessories

Notes: 3,5mm TRS to male DIN 5

150cm length

Notes: 3,5mm TRS to male DIN 5

150cm length

Notes: The 2-row rack for AE modular is 16 units wide with 2 rows; the MASTER module consumes 2 units so you have 30U remaining for other modules.

Via a joint kit (not included) another case of this width (either one-row or two-row) can be attached at a free angle; the bus is connected via a short connector cable between both cases.

The sides are made of red acrylic, all other parts are of wood fibre board (MDF), black painted.

Dimensions: 41.3 x 21.7 x 4.5 cm (width x depth x height)

Notes: The 1-row rack for AE modular is 16 units wide; two of them are used by the MASTER module so you have 14U remaining for other modules.

Via a joint kit (not included) another case of this width (either one-row or two-row) can be attached at a free angle; the bus is connected via a short connector cable between both cases.

The sides are made of red acrylic, all other parts are of wood fibre board (MDF), black painted.

Dimensions:41.3 x 11.2 x 4.5 cm (width x depth x height)

Notes: Low-cost, portable, compact enclosure that turns Eurorack modules into table-top instruments.

The Pod20 is 20HP with 1.34" (34mm) of available module depth. The built-in power supply has two power connectors and can be daisy-chained to other Pods. More power connectors can be added with the Multi Power Cable accessory.

Pods require a power brick. If you already have a powered Pod and power brick (or a Row Power module) you can use a barrel cable to daisy-chain powered Pods.

The Pod20 includes ten (10) M3x8mm stainless steel screws and is compatible with M3 Knurlies.

Notes: Low-cost, portable, compact enclosure that turns Eurorack modules into table-top instruments.

The Pod32 is 32HP with 1.34" (34mm) of available module depth. The built-in power supply has two power connectors and can be daisy-chained to other Pods. More power connectors can be added with the Multi Power Cable accessory.

Pods require a power brick. If you already have a powered Pod and power brick (or a Row Power module) you can use a barrel cable to daisy-chain powered Pods.

The Pod32 includes ten (10) M3x8mm stainless steel screws and is compatible with M3 Knurlies.

Notes: Small desktop enclosure for Eurorack modules with 42 HP space and a maximum depth of 32mm. A relatively strong power solution with an external power supply and an on/off switch located at the case is included.

The power supply provides:

- 850 mA at +12V
- 850mA at -12V
- 500mA at +5V

The power distribution has 14 connectors and the case can house exactly fourteen modules from Erica's Pico Series.

Notes: Mariana Trench is an FDN card for the Z-DSP. Feedback Delay Networks (FDNs) are built around multiple delays which are connected to their inputs thanks to a feedback matrix designed for its stability and lossless properties. FDN can mimic the recursive process of sound waves bouncing back and forth in an acoustic space. They were first suggested for artificial reverberation by Michael Gerzon (1971) and later John Stautner and Miller Puckette (1982) introduced four-channel FDN reverberator with general stability conditions.

FDN can also be used as a special case of digital waveguides, they can be tuned, or also used as complex delays. The Mariana Trench Z-DSP cartridge is designed to explore these more unusual sides of the FDN algorithms. Mariana Trench Z-DSP cartridge is designed by Christophe Duquesne Anckorage - Haken Audio developement team - La Voix du Luthier.

Notes: Qu-Splitter is a 1 input to 5 output cable hub for splitting signals. These are a great alternative to mult modules as they live outside of your case and take up 0HP. Very useful for common signals like master clock, modulation sources, or even to chain multiple cables together for long reach patching!

- 1 input to 5 outputs
- 0Passive mult
- Great for common signals like master clock, and modulation sources
- Connect two cables together for long reaches
- Color: Black with white artwork

Notes: Flying Bus (male pin) are passive power distribution cables that work with the Row Power to distribute power to your modules.

Can be daisy-chained if extra headers are needed. One 14" flying bus cables with 7 male header pins.

Notes: Blank panel, 1HP, constructed from anodised aluminium, silver.

Notes: Blank panel, 1.5 HP, constructed from anodised aluminium, silver.

Notes: Blank panel, 2HP, constructed from anodised aluminium, silver.

Notes: Blank panel, 4HP, constructed from anodised aluminium, silver.

Notes: Blank panel, 8HP, constructed from anodised aluminium, silver.

Notes: Blank panel, 42HP, constructed from anodised aluminium, silver.

Notes: A-100SSB is a combination of power supply and bus board with 8 connectors for A-100 modules, planned for applications with up to 8 modules and a max. current of 380 mA.

- Wide range mains voltage input 100-240V AC / 50-60 Hz
- IEC inlet on board for the connection of a suitable mains cable (a suitable mains cable has to be purchased by the customer locally, it's not included with the A-100SSB)
- Switching supply with +12V/380 mA and -12V/380mA for the operation of A-100 modules up to 380 mA total supply current
- Safety cover at the bottom side (covers all elements that lead mains voltage)
- On board fuse
- 8 bus connectors
- LED displays for +12V, -12V and +5V
- Dimensions: about 270 mm (length) x 55 mm (width) x 35 mm (height)
- Several 3mm holes for mounting the unit on a rear panel or bottom plate

Notes: High quality rotary knob, for use with Doepfer or a wide range of modules. Robust design with indented edges. Grey finish.

Notes: High quality rotary knob, for use with Doepfer or a wide range of modules. Robust design with indented edges. Red finish.

Notes: High quality rotary knob, for use with Doepfer or a wide range of modules. Robust design with indented edges. Green finish.

Notes: High quality rotary knob, for use with Doepfer or a wide range of modules. Robust design with indented edges. Yellow finish.

Notes: High quality rotary knob, for use with Doepfer or a wide range of modules. Robust design with indented edges. Retro style finish.

Notes: Break out MIDI signals into a 3.5mm stereo jack.

- Tip = Pin 4 (Source)
- Ring = Pin 5 (Sink)
- Sleeve = Pin 2 (Shield)

Notes: Custom ALM patch cables. Small but strong, they are designed for maximum ergonomic post modern wiggling.

- 60cm (Pack of 5 + ALM branded tie)
- Colour: Purple

Notes: Custom ALM patch cables. Small but strong, they are designed for maximum ergonomic post modern wiggling.

- 90cm (Pack of 3 + ALM branded tie)
- Colour: White

Notes: We wanted to organize patch cables that were hanging on all possible objects in our Lab, therefore we decided to make patch cable holders.

Rigid, 2mm aluminium powder coated cable holders can host over 100 patch cables in perfect order! Two screws for fixing the cable holder are included.

Notes: The new, 2nd generation Audio Jacks Board comes pre-installed in every Intellijel 7U case manufactured since early 2019. Because this board is more fully featured than the previous generation, it's available as a stand-alone component for anyone who wishes to update an older 7U case.

You can tell which board you have by looking at the connectors. The new Audio Jacks Board has a large shrouded header flanked by two smaller shrouded headers, flanked by two link connectors at either end. Older boards have only one connector along the bottom edge.

The board holds four Neutrik TRS jacks, each of which can be configured as either an input or an output depending on the modules you connect. This allows you maximum flexibility when configuring your case - whether you wish to use the audio jacks as outputs, inputs, sends & returns; or some combination of these.

The jacks carry different audio signals depending on what you connect to the Audio Jacks Board. Please refer to the manual for more details on the many options available.

Notes: Your Palette case is the ideal solution for your space conscious and portable needs. At about the same size as a small laptop, your Palette fits comfortably on your desktop; in your backpack; at your favourite coffee shop; in your jam space; or pretty much anywhere else you might desire to play. Your imagination is the only limit. With 62hp of rack space, you can piece together powerful but focused mini systems and control surfaces. Intellijel's 1U row and built-in i/o ports add a ton of extra utility to bring the most out of your Eurorack modules. Truly a palette for the sonic artist.

Utilities panel:

- Dual 1:4 buffered multiple
- Two 1/4" balanced audio jacks that can be connected to the Stereo Line Out 1U, Pedal I/O 1U or Mixup
- 1/8" (6.35mm) MIDI Input that can be connected to uMIDI 1U
- USB port that connects to the uMIDI 1U and other future modules
- Rocker switch and barrel plug for power entry

Construction:

- Anodized aluminium
- Aluminium extruded rails with steel threaded inserts
- Rubber feet to protect your desktop
- Rear mounted power supply for maximum module depth

Includes:

- 40W Meanwell AC/DC adapter with right angled connector
- 3FT North American IEC power cable
- 1/8" (6.35mm) TRS to 5-Pin Din MIDI adapter

Notes: Bananuts are anodized aluminium custom minijack nuts, following Buchla/Serge colouring code: Blue, purple, red, orange, yellow, white, green and black. Perfect lovely thingies to pimp your modular, code your inputs and outputs with colours or just give a touch of beauty to your favourite gear!

Notes: Bananuts are anodized aluminium custom minijack nuts, following Buchla/Serge colouring code: Blue, purple, red, orange, yellow, white, green and black. Perfect lovely thingies to pimp your modular, code your inputs and outputs with colours or just give a touch of beauty to your favourite gear!

Notes: Bananuts are anodized aluminium custom minijack nuts, following Buchla/Serge colouring code: Blue, purple, red, orange, yellow, white, green and black. Perfect lovely thingies to pimp your modular, code your inputs and outputs with colours or just give a touch of beauty to your favourite gear!

Notes: Bananuts are anodized aluminium custom minijack nuts, following Buchla/Serge colouring code: Blue, purple, red, orange, yellow, white, green and black. Perfect lovely thingies to pimp your modular, code your inputs and outputs with colours or just give a touch of beauty to your favourite gear!

Notes: Bananuts are anodized aluminium custom minijack nuts, following Buchla/Serge colouring code: Blue, purple, red, orange, yellow, white, green and black. Perfect lovely thingies to pimp your modular, code your inputs and outputs with colours or just give a touch of beauty to your favourite gear!

Notes: Bananuts are anodized aluminium custom minijack nuts, following Buchla/Serge colouring code: Blue, purple, red, orange, yellow, white, green and black. Perfect lovely thingies to pimp your modular, code your inputs and outputs with colours or just give a touch of beauty to your favourite gear!

Notes: Bananuts are anodized aluminium custom minijack nuts, following Buchla/Serge colouring code: Blue, purple, red, orange, yellow, white, green and black. Perfect lovely thingies to pimp your modular, code your inputs and outputs with colours or just give a touch of beauty to your favourite gear!

Notes: Custom wrench for 3.5mm jacks, designed for Bananuts or other slotted round 3.5mm nuts.

Notes: Bus board to connect 14 modules

An assembled and tested bus board, 22 sockets, e.g. for customers who want to built their own case and need a bus board for A-100 modules, includes cables for connection to +/-12V power supply (4 wires with flat connectors on both ends, length about 30cm), but no mechanical parts (e.g. screws, spacers, nuts, washers).

In the new version of the A-100 bus board (labeled Version 6 / 2019) boxed pin headers are used which are equipped with a reverse protection (gap for the "nose" of the socket of the bus cable). When the bus cable coming from the module is connected to the boxed header in question the "nose" has to point to the right. The polarity of the cable is correct if the red wire of the bus cable then points to the bottom (to the continuous line labeled"RED WIRE" on the pc board). If this is not the case please do not connect the module to the bus board ! Otherwise both the module and the power supply (A-100PSU3) may be damaged ! In that case please contact the manufacturer of the module and ask for a suitable bus cable with the correct polarity of the connector.

The bus cables of original A-100 modules manufactured by Doepfer are equipped with suitable bus cables since 2012. Only for older A-100 modules manufactured before 2012 it may happen that the polarity of the 16 pin female connector of the bus cable is wrong (nose points to the left when red wire points to the bottom). This is because in the past unboxed pin headers were used and the position of the "nose" did not matter. In such a case please contact Doepfer or one of their dealers and order a suitable bus cable.

Notes: Low-cost, portable, compact enclosure that turns Eurorack modules into table-top instruments.

The Pod34X is 34HP wide and has extra room to fit even the deepest modules (2.16" / 55mm of available module depth). The built-in power supply has four power connectors and can be daisy-chained to other Pods. More power connectors can be added with the Multi Power Cable accessory.

This Pod requires a power brick (not included).

Or, if you already have a Pod and power brick (or a Row Power module) you can use a barrel cable to daisy-chain power supplies.

Pods are a perfect way to get started in Eurorack, or add a couple more modules to your monster system!

Made from 100% anodized aluminum, Pods are light, tough and perfect for on-the-go set ups. The power supply can handle up to 1.4A of +12V, which is plenty of juice for even the most modern digital modules. (Or if you prefer to DIY your power supply, Pods are also available unpowered)

Each Pod typically will house one or two modules, but three or more can be accommodated using a multi-power cable accessory.

Mix and match your Pods with desktop synths, effect pedals, drum machines or any musical gear for a flexible modular system. Pods can even daisy- chain with the 4ms Row Power system making them a convenient outboard mini-skiff. Need to add another module? Just add a Pod! Need to pack light for a live set? Just grab the Pods you need and go!

Basic Features:

34 HP Eurorack modular space
Standard M3 threaded holes
100% lightweight anodized aluminum
Built-in Power supply
Red, White, and Blue LED power indicators

Includes:
34HP Pod, black anodized aluminum
Extra deep (2.16"/55mm) fits virtually every Eurorack module
Built-in power supply with four Eurorack power headers
M3 x 8mm pan-head screws, stainless steel (10)
Adhesive rubber feet (4)
Does not include barrel cable or power brick
Power Supply:
Four 16-pin Eurorack power shrouded headers
+12V max 1.4A
-12V max 0.65A
+5V max 1.0A
Power input: Two barrel jacks for daisy-chaining
15V-20VDC, 2.1mm positive tip
Exterior dimensions:
Width: 177.3mm (6.98")
Height: 159.5mm (6.28")
Depth: 57mm (2.24")
Interior dimensions:
Max module depth: 55mm (2.16")
Module width: 34HP
Weight:
0.3 kg = 10 oz

Notes: Low-cost, portable, compact enclosure that turns Eurorack modules into table-top instruments.

The Pod64X is 64HP with 2.16" (55mm) of available module depth. The built-in power supply has four power connectors and can be daisy-chained to other Pods. More power connectors can be added with the Multi Power Cable accessory.

Pods require a power brick, or a barrel cable to daisy-chain to a Pod or Row Power that's already powered.

Pods are a perfect way to get started in Eurorack, or add a couple more modules to your monster system!

Made from 100% anodized aluminum, Pods are light, tough and perfect for on-the-go set ups. The power supply can handle up to 1.4A of +12V, which is plenty of juice for even the most modern digital modules. (Or if you prefer to DIY your power supply, Pods are also available unpowered)

Each Pod64X typically will house up to six modules, but more can be accommodated using a multi-power cable accessory.

Mix and match your Pods with desktop synths, effect pedals, drum machines or any musical gear for a flexible modular system. Pods can even daisy- chain with the 4ms Row Power system making them a convenient outboard mini-skiff. Need to add another module? Just add a Pod! Need to pack light for a live set? Just grab the Pods you need and go!

Basic Features:

64 HP of Eurorack modular space
Extra room for deep modules
Standard M3 threaded holes
100% lightweight anodized aluminum
Built-in Power supply
Red, White, and Blue LED power indicators

Includes:

64HP Pod, black anodized aluminum
Built-in power supply with six Eurorack power headers
Extra deep (2.16"/55mm) fits virtually every Eurorack module
M3 x 8mm pan-head screws, stainless steel (20)
Adhesive rubber feet (4)
Does not include barrel cable or power brick
Power Supply:

Four 16-pin Eurorack power shrouded headers
+12V max 1.4A
-12V max 0.67A
+5V max 1.0A
Power input: Two barrel jacks for daisy-chaining
15V-20VDC, 2.1mm positive tip
Exterior dimensions:
Width: 329.7mm (12.98")
Height: 159.5mm (6.28")
Depth: 57mm (2.24")
Interior dimensions:
Max module depth: 55mm (2.16")
Module width: 64HP
Weight:
0.5 kg = 17 oz

Notes: Low-cost, portable, compact enclosure that turns Eurorack modules into table-top instruments.

The Pod64X Unpowered is 64HP with 2.16" (55mm) of available module depth. No power supply is included, you must supply your means of powering modules with a DIY power supply or a front-facing module such as the Row Power. Two holes on the rear face are plugged with removable plastic plugs, and can be used for DIY applications.

Pods are a perfect way to get started in Eurorack, or add a couple more modules to your monster system!

Made from 100% anodized aluminum, Pods are light, tough and perfect for on-the-go set ups. Mix and match your Pods with desktop synths, effect pedals, drum machines or any musical gear for a flexible modular system. Need to add another module? Just add a Pod! Need to pack light for a live set? Just grab the Pods you need and go!

Basic Features:

64 HP Eurorack modular space
Standard M3 threaded holes
100% lightweight anodized aluminum

Includes:

64HP Pod, black anodized aluminum
M3 x 8mm pan-head screws, stainless steel (20)
Adhesive rubber feet (4)
Unpowered: requires you to provide your own Eurorack power system
Exterior dimensions:
Width: 329.7mm (12.98")
Height: 159.5mm (6.28")
Depth: 57mm (2.24")
Interior dimensions:
Max module depth: 55mm (2.16")
Module width: 64HP
Weight:
0.42 kg = 14.9 oz

Notes: Low-cost, portable, compact enclosure that turns Eurorack modules into table-top instruments.

The Pod60 Unpowered is 60HP with 1.34" (34mm) of available module depth. No power supply is included, you must supply your means of powering modules with a DIY power supply or a front-facing module such as the Row Power. Two holes on the rear face are plugged with removable plastic plugs, and can be used for DIY applications.

Notes: Low-cost, portable, compact enclosure that turns Eurorack modules into table-top instruments.

The Pod60 is 60HP with 1.34" (34mm) of available module depth. The built-in power supply has four power connectors and can be daisy-chained to other Pods. More power connectors can be added with the Multi Power Cable accessory.

Pods require a power brick. If you already have a powered Pod and power brick (or a Row Power module) you can use a barrel cable to daisy-chain powered Pods.

The Pod60 includes twenty (20) M3x8mm stainless steel screws and is compatible with M3 Knurlies.

Notes: 16-conductor ribbon cable with four 16-pin connectors (20" total length), for connecting more than 2 modules in a Pod.

Notes: M2.5 screws have gained popularity in the US with manufacturers such as Elite, Make Noise, and anyone using Vector rails.

Notes: Bus Sticks are low-profile, small footprint power distribution boards for powering up to 13 modules using shrouded (keyed) headers. Simply connect to a Row Power module using the included cable. Attaches to your case using adhesive pads (included) or by drilling and screwing.

Notes: The Pod48X is 48HP with 2.00" (51mm) of available module depth. The built-in power supply has four power connectors and can be daisy-chained to other Pods. More power connectors can be added with the Multi Power Cable accessory.

Pods require a power brick. If you already have a powered Pod and power brick (or a Row Power module) you can use a barrel cable to daisy-chain powered Pods.

The Pod48X includes ten (10) M3x8mm stainless steel screws and is compatible with M3 Knurlies.

Notes: The Mini Case offers 40 HP for mounting modules. A power supply is built-in.

208 mm long x 45mm deep.

PLEASE NOTE: Comes with EU 2 pin plug only - UK adapter may be required.

Notes: Z-Rails Brackets are used to attach Z-Rails to wood cases without having screws visible on the exterior for a clean, professional finish. Z-Rails Brackets have two holes for wood screws and two holes for Z-Rails screws. Z-Rails Brackets come supplied with both types of screws and no additional screws are required for assembly.

Notes: These cables are designed to interconnect pro audio gear with balanced phone jacks. They are ideal for use with balanced phone patch bays. Features include:

- Nickel-plated plugs for rugged durability and efficient signal transfer
- Oxygen-Free Copper (OFC) conductors for enhanced signal clarity
- OFC spiral shields for effective EMI and RFI rejection and flexibility

Connectors: 1/4 in TRS to Same
Conductors: 26 AWG x 2 OFC
Shield: 85% OFC Spiral
Quantity: 8 pc

Notes: The Happy Ending Kit is an easy way to get everything needed to start a Eurorack modular system.

The Happy Ending Kit includes:
1 x Z-Rails set plus screws to attach to Z-Ears
1 x uZeus 4HP PSU with 2 x flying bus boards
1 x UK 3-pin mains adapter