100% Sicheres Einkaufen

Studio equipment

Our full range of studio equipment from all the leading equipment and software brands. Guaranteed fast delivery and low prices.

Visit Juno Studio

100% Sicheres Einkaufen

DJ equipment

Our full range of DJ equipment from all the leading equipment and software brands. Guaranteed fast delivery and low prices.Visit Juno DJ

Four Weeks: All Genres

Format: All Vinyl CD DJ Equipment Studio Equipment
View:
Options
Artikel 1 bis 11 von 11 auf Seite 1 von 1 anzeigen
Cat: 731235 Rel: 15 Jul 19
 
Adds routing flexibility to signal chains of guitar pedal effects, electronic instruments & other audio devices
Notes: Are you playing with your cables more than your pedals? The Terminal adds new routing possibilities to a more permanent setup. Its half-normalled wiring, which is also used in recording studio patch bays, allows an audio signal to pass "normally" and to be copied from the Green SND jack without interruption. However, the signal can also be cut off or replaced by patching into the RTN jack. It's easy to insert effects and re-route instruments without pulling your rig apart.

This simple but very useful design was originally a custom project for musician Tycho, who is using Terminal in his studio and live rigs to quickly patch between sections of pedal and instrument chains. Community interest in the product has led Boredbrain to produce Terminal in limited batches. Each unit is hand-built; from drilling and printing to wiring, soldering and assembling.

Pedalboard access points:

Each Terminal channel is placed at specific points in the signal chain. New effects can then be inserted at these points, or entire sections can be bypassed using a single cable.

Instruments patch hub:

Each Terminal channel is a dedicated patch point for an instrument signal on its way to a mixer or DAW. Effects can be inserted into the signal easily, or it can be copied to another channel.
Read more
 3 in stock $91.22
Click for better price!
quote 731235
Cat: 577791 Rel: 10 Jul 19
 
VCA with exponential response for low level sensitivity - 8HP
Notes: Module A-131 provides voltage-controlled amplification. For audio signals, you would normally use the exponential VCA (A-131), and for control voltages, the linear VCA (A-130). It doesn't always have to be that way, though.

The amount of amplification the VCA's provide is determined by the voltage at the CV input, and the position of the gain control, which sets the overall gain in the system.

The VCA has two audio inputs, each with an attenuator. They are amplified by an amount determined by the combination of the gain and the two CV controls.
Read more
 1 in stock $71.52
Click for better price!
quote 577791
Cat: 577763 Rel: 10 Jul 19
 
8HP Eurorack module featuring two identical VCA's
Notes: Module A-132-3 is composed of two identical voltage controlled amplifiers (VCA). Each VCA has a manual gain control and a control voltage input with attenuator. The character of the control scale can be switched to linear or exponential. All inputs and outputs are DC coupled. Consequently, the VCA's can be used to process both audio and control voltages. The input has no attenuator available but is capable to process up to 16Vss signals (i.e. -8V...+8V) without distortion.
Read more
 1 in stock $95.36
Click for better price!
quote 577763
Cat: 738616 Rel: 10 Jul 19
 
Stereo headphone amplifier - 6HP
Notes: The A-139-2 is a headphone amplifier module with two mono inputs and a stereo headphone output. It can be used for driving small loudspeakers, LED strips, small magnets etc.

- Two-channel headphone amplifier
- Two audio inputs with level controls
- Input 1 is normalled to Input 2
- Common loudness/master level control
- Headphone output (stereo 1/4" jack socket)
- Max. output power ~ 2 W per channel (@ 8 Ohm load)
- DC coupled inputs and outputs (i.e. also useful for other applications like small loudspeakers, lamps, LEDs, magnets, motors - provided that the power is sufficient)
Read more
 1 in stock $51.82
Click for better price!
quote 738616
Cat: 738617 Rel: 10 Jul 19
 
Versatile module that can also be used as a modulation device - 8HP
Notes: Module A-140-1 is an envelope generator, and, since it puts out control voltages, counts as one of the modulation devices in a modular system. As soon as the gate input receives sufficient voltage, the ADSR generates a variable voltage, changing in time, called an envelope. This varying voltage is output in normal (positive) and inverted form, and can be used, eg. for voltage controlled modulation of a VCO, VCF, or VCA, or for processing other modules' inputs and outputs.

The shape of the envelope is governed by four parameters: Attack, Decay, Sustain and Release.

The envelope is started (triggered) by a gate signal either from the INT.GATE voltage on the system bus, or, if a signal is put into it, from the gate input socket.

The envelope can also be re-triggered, i.e. start from scratch again, each time a trigger signal is sensed at the Retrig. input socket, when the gate is still open.

Module A-140 has available a three-position toggle switch to select one of three time ranges. The time ratios for the three ranges are about 1 : 20 : 1000. The absolute Attack times are about:

20uS ... 100ms (switch position L)
400uS ... 2s (switch position M)
20ms ... 120s (switch position H)
The Decay and Release times are about 3-4 times more. Because of the exponential slope and the gradual asymptotic approach to the zero level the exact specification of the decay and real times is a bit difficult.

The voltage ranges of the ADSR outputs are about 0 ... +8V for the two normal outputs and 0 ... -8V for the inverted output.

In combination with the Comparator module A-167 a free-running "ADSR-LFO" can be realized.
Read more
 1 in stock $76.68
Cat: 738621 Rel: 10 Jul 19
 
Voltage controlled envelope generator with decay parameter - 8HP
Notes: Module A-142-1 is a voltage controlled envelope generator. The only time parameter is decay (like TB303). Decay may be adjusted manually and via voltage control input (with attenuator). The envelope output is displayed with LED control. Additionally from the envelope signal a Gate signal and an inverse Gate signal with adjustable threshold is derived. LED control for Gate output. Thus one obtains a voltage controlled Gate additionally or alternatively to the envelope signal with voltage controlled duration.

The attack time is fixed to about 0.2 ms, the shortest decay time is about 2 ms. By changing the value of a capacitor the shortest time can be modified (details can be found here: A100_Capacitors.htm).

Typical applications: dynamic control of decay e.g. in combination with the Analog/Trigger Sequencer A-155, voltage controlled trigger delay functions (like A-162, but voltage controlled).
Read more
 1 in stock $76.70
Click for better price!
quote 738621
Cat: 738632 Rel: 09 Jul 19
 
Quad Decay featuring four simple envelope generators - 8HP
Notes: Module A-142-4 contains four simple envelope generators. The only time parameter is Decay and can be adjusted manually by means of the Dec. control in the range 2 ms ... 2 seconds. The attack time can be adjusted internally by means of a separate trimming potentiometer for each sub-unit in the range 1 ms ... 15 ms. The factory setting is about 3 ms. This is the attack time of the TB303. Each envelope output has a LED control available. The trigger inputs are normalled (1 -> 2 -> 3 -> 4).

Suggestions for modifications:

Each sub-unit has a pin header with two pins available. When the two pins are shortened (e.g. by means of a jumper or a toggle switch connected to the two pins) the corresponding sub-unit changes to a loop mode. In this mode the unit is triggered by itself like an LFO..

By changing the value of a capacitor the time range can be modified (e.g. 0.2 ms ... 0.2 seconds or 20 ms ... 20 seconds)
Read more
 1 in stock $92.25
Click for better price!
quote 738632
Cat: 738640 Rel: 09 Jul 19
 
Voltage controlled sine-LFO with four separate, phase shifted outputs - 8HP
Notes: Module A-143-9 is a derivative of our planned thru-zero quadrature VCO. It is a voltage controlled sine LFO with 4 outputs. The phase shift between the outputs is 90 degrees. The sine shifted by 90 degrees is also called cosine, the sine shifted by 180 degrees is nothing but the inverted sine, and the sine by 90 degrees is nothing but the inverted cosine.

The frequency range is from some minutes to frequencies beyond audio with three ranges selected by a toggle switch:

- Switch position H: about 30 Hz ... 3.5 kHz with the manual frequency control ("Frq."), beyond 20 kHz with additional external CV
- Switch position M: about 1 Hz ... 150 Hz with the manual frequency control ("Frq.")
- Switch position L: about 0,1 Hz ... 10 Hz with the manual frequency control ("Frq."), down to several minutes with additional external CV

Two exponential frequency control inputs are available: CV1 without attenuator and CV2 with polarizer. Consequently the module can be used even as an experimental sine VCO but does not feature an exact 1V/oct CV input! The precision CV input will be left to the thru-zero quadrature VCO.

Two LEDs display the positive and negative share of the sine output.

The core of the module is a so-called quadrature circuit that generates a sine a cosine signal with very low distortion. The quality of the sine/cosine signals are much better than those generated by a waveform converter with a sawtooth or triangle signal as starting point.

The output levels are about 5 Vss (+/-2.5V) but can be adjusted internally by a trimming potentiometer (P5 "Shape").

Typical applications:

- External sine/cosine oscillator for the frequency shifter A-126
- Modulations with pure sine/cosine waveforms
- Quadrature/barberpole effects (e.g. with the voltage controlled mixer A-135)
- Experimental sine/cosine VCO (e.g. for FM sounds)

Many users suggested to add a common output level control, i.e. four VCAs with one common control (manual + CV without attenuator + CV with polarizer) for the output levels. This is why we also designed the Quad VCA module A-132-2 with the possibility of an internal default connection to the four outputs of the A-143-9 (no soldering required, short 10 pin flat cable with removable connectors on both ends).

The A-143-9 is also a meaningful addition for the Frequency Shifter module A-126. It enables frequency shifting even below 50 Hz generating e.g. these mellow beat sounds with a few Hz frequency shifting only. The following document describes how to connect the A-126 and the A-143-9: A126_A143_connection.pdf.

The thru zero version of the A-143-9 with temperature compensation is the module A-110-4.
Read more
 1 in stock $75.67
Click for better price!
quote 738640
Cat: 738645 Rel: 10 Jul 19
 
Low frequency oscillator with adjustable waveform - 8HP
Notes: Module A-146 (LFO 2) is a Low Frequency Oscillator, which produces periodic control voltages over a wide range of frequencies.

The LFO can be used as a modulation source for a series of modules (for instance pulse width and/or frequency modulation of a VCO, modulation of a VCF cut-off frequency, amplitude modulation with a VCA).

Three outputs are available, with different waveforms: sawtooth / triangle; square wave, and positive-voltage square wave.

The waveform is continuously adjustable from rising sawtooth, through triangle to falling sawtooth. The same control affects the pulse width of the square wave.

A three-way switch can select one of three frequency ranges, spanning from one cycle every few minutes, at the lowest, up to audio frequency at the highest.
Read more
 1 in stock $67.37
Click for better price!
quote 738645
Cat: 739137 Rel: 16 Jul 19
 
Voltages expander for Permutation - black faceplate, 6HP
Notes: Variant is an expander module based on the original Voltages expander for the Turing Machine. Variant adds two additional bipolar CV outputs (with modulation inputs) that are derived from Permutation's gate sequence.
Read more
 1 in stock $94.33
Click for better price!
quote 739137
Cat: 731217 Rel: 18 Jun 19
 
Expander for Quad Operator's algorithm functionality - 4HP
Notes: Where the unexpanded Quad Operator maintains a one knob per function design discipline, we nevertheless recognized the value of some more advanced algorithm-oriented functionality.

The Algo expander for the Quad Operator provides:

- Saving and loading of modulation send knob positions for FM algorithm design reuse

- Crossfade between pairs of saved algorithms, or a saved algorithm and the live knob positions
Read more
 2 in stock $95.36
Click for better price!
quote 731217
Artikel 1 bis 11 von 11 auf Seite 1 von 1 anzeigen

Filter

Four Weeks: All Genres
Close