New releases last eight weeks: All genres

Notes: Michael Gira - The Knot: Complete Words for Music, Collected Stories and Journals

Paperback; 7 1/4 x 10 1/4 inches, 408 pages, includes 101 colour images printed on high quality photographic paper.

Paperback has bookplate signed by M Gira.

Journals, stories, and songs span the years 1981 to present. Includes visual archives and artwork dating back to 1974.

"From the Preface to The Knot: This book contains the words to every song I've written worth collecting to date from all my musical projects throughout the years. I've left out various imbecilities and feckless half-starts. Also included in this book are several previously published short stories. They're taken from the collections The Consumer and The Egg, as well as a few other hand- made limited editions of stories. In a few cases I've included excerpts rather than the entire story. This was done for aesthetic purposes, with the overall feel of this current volume in mind. There are a great many journal entries in this book. For the most part they are also, emphatically fiction. They're from an ongoing journal, not a diary. My journals are where I often allow a disembodied, fictional 1st person narrator to take over and unspool imagined events, diatribes, impossible scenarios, psychic auto-cannibalisms, and corrosive or ecstatic dreams etc. Again, these are fiction. Certain things I've written about (in fiction and in song form) seem to exist beneath the surface (in myself and others) and I find them compelling to look at and to describe. I view this as a positive act. In acknowledgment of the constricting and microscopically judgmental and censorious times we live in, the usual authorial caveats apply here. Certainly there are many purely anecdotal journal entries included in this book as well, and my presumption is that an intelligent reader would be able to differentiate one from the other. Personally, I'm very suspicious of memory (especially my own), so I can't definitively vouch for the veracity of the recounting of the literal events herein either. I have also excised material that I felt too personal to include, out of respect for the people involved as well as for myself. There are several large gaps in the journal entries over the years. This is due to lost journals of the time, and in one case a lost laptop (which, painfully, contained a great deal of writing). There are also periods where I didn't keep a journal and didn't write fiction. In any event, I've tried to include fiction and journal entries that correspond roughly to the period before and after a musical album's release and the words that were written for that music. The end section of this book consists of recently unearthed visual documents and imagery and functions here as an incidental archive. The images span the years from 1974 to the present."

Michael Gira

Notes: Following "Vintage Music T-shirt Scrap", The long-awaited third instalment of the scrap series is Jazz!

Focusing on jazz, focusing on original vintage posters, From flyers to booklets, calendars, and magazines of performances at the time!

There are many jazz record jacket books in the world, but this is the first poster book in the world.

Ide started by searching for materials for his autobiographical book "Rolling On The Road". Ninety percent of the items in the collection were collected intensively by Ide over a period of about a year and a half. "

Binding: 376 pages / A5 format

Notes: The AlphaTheta Omnis Duo, a state-of-the-art DJ controller developed by AlphaTheta, has swiftly garnered praise for its groundbreaking features and unmatched performance qualities. Acknowledging its crucial contribution to the evolution of contemporary DJing, and in answer to the passionate call for dependable protection, Decksaver are delighted to unveil the Decksaver cover, custom-made for the Omnis Duo. Precision-engineered from superior polycarbonate, this cover is carefully crafted to provide the utmost protection for your Omnis Duo, safeguarding it against dust, spills, and unexpected impacts, thus ensuring its durability and peak performance.

With an eye for detail, this Decksaver cover perfectly matches the distinct contours of the AlphaTheta Omnis Duo, offering a tight fit that covers all essential components, such as knobs, buttons, and screens. Despite its strong protection, the cover allows easy access to vital connections, facilitating straightforward setup and disassembly for both live performances and studio use. Whether you're in the heat of a lively DJ set, a busy studio setting, or during storage, this cover acts as a steadfast protector, maintaining the immaculate condition and operational capabilities of your Omnis Duo.

Opting for this Decksaver cover for your AlphaTheta Omnis Duo is more than just about safeguarding; it symbolises a dedication to the care and upkeep of a key element of your DJ equipment. Held in high esteem and trusted by professionals in the industry, this cover is an essential addition for anyone committed to preserving the integrity and longevity of their AlphaTheta Omnis Duo, ensuring it stays ready for every DJing venture and creative pursuit.

Dimensions

Weight: 0.56 kg
Length: 50.5 cm
Width: 31.2 cm
Height: 3.1 cm

Material: Smoked clear polycarbonate.

WARNING: When your Decksaver cover is in place, please ensure that your equipment is kept away from direct and high heat sources, such as radiators, fires and sunlight.

Notes: Enhance your DJing experience with the Native Instruments Traktor X1, an essential controller for Traktor DJs seeking refined control over their mixes. Now, protect your investment with the Decksaver cover, the premier protection solution crafted to keep your X1 in mint condition, whether you're in the studio, on the move, or at home.

The Traktor X1 Decksaver lid is intricately designed to offer a perfect fit, providing unmatched protection for your controller. Developed with precision moulding in-house, this cover easily accommodates cables, enabling you to keep your setup neat and organised. By shielding your Traktor device from damage due to accidental knocks, dust, and spills, the Decksaver cover becomes an indispensable accessory for any DJ who cherishes their equipment.

Prioritising durability and functionality, the X1 cover ensures your controller's sensitive controls and internal components are kept intact. Its sturdy construction serves as a defence against the challenges of travel and the perils of daily use. Whether transporting your equipment to a performance or storing it between uses, the Decksaver cover delivers reliable protection that surpasses conventional methods.

Do not settle for less when it comes to the performance and longevity of your Native Instruments Traktor X1. Opt for the Decksaver cover and afford your controller the attention it requires during breaks, ensuring it's always primed to channel your creativity instantly. Maintain your gear in exceptional condition and enjoy peace of mind with the Traktor X1 Decksaver cover, for DJs who accept nothing but the best.

Weight: 0.175 kg
Length: 13.4 cm
Width: 32.7 cm
Height: 4.2 cm

Material: Smoked clear polycarbonate.

WARNING: When your Decksaver cover is in place, please ensure that your equipment is kept away from direct and high heat sources, such as radiators, fires and sunlight.

Notes: The new MULTI-FORMAT CASE PLAYER/MIXER (V10/A9) SET is specifically designed for transporting two CDJ/Multimedia Players and a 6 or 4-channel club mixer, such as the Pioneer DJM-V10, DJM-A9, or Ecler Warm 4. The case is universally compatible with all current models from Pioneer DJ, Denon, Allen & Heath, Ecler, Rane and Reloop, and can be adjusted to different device sizes using the included foam strips. Crafted from 9 mm vinyl laminated plywood, sturdy aluminum profiles, heavy duty butterfly latches and smooth rolling wheels, this case provides ultimate protection for mobile use on the road.

Fits

Pioneer DJM-V10
Pioneer DJM-A9
Pioneer DJM-900 NXS2
Pioneer DJM-900 NXS / SRT
Pioneer DJM-800 / 700 / 600
Pioneer CDJ-3000
Pioneer CDJ-2000 NXS2
Pioneer CDJ-2000 NXS
Pioneer CDJ-900 / 850 / 800
Pioneer XDJ-1000
Allen & Heath PX5
Allen & Heath DB4
Allen & Heath DB2
Allen & Heath Xone 92 / 62 / 43C
Denon LC 6000 Prime
Denon SC-6000 / SC-6000M
Denon SC-5000 / SC-5000M
Denon X1850 / X1800
Denon X1600
Denon SC3900
Denon SC2900
Reloop RMX-90 DVS
Reloop RMX-80 Digital
Ecler Warm 4
Ecler NUO4
Rane MP2015
Rane Sixty-Eight / Sixty-Four

Specs

Outer measures: 125,4 x 59 x 25 cm
Inner measures: 33,1 x 42,5 x 8,4 cm / (CDJ compartment) 43,7 x 45,4 x 8,4 cm (Mixer compartment)
Weight: 21,5 kg

Notes: The new MULTI-FORMAT CASE PLAYER/MIXER (V10/A9) SET is specifically designed for transporting two CDJ/Multimedia Players and a 6 or 4-channel club mixer, such as the Pioneer DJM-V10, DJM-A9, or Ecler Warm 4. The case is universally compatible with all current models from Pioneer DJ, Denon, Allen & Heath, Ecler, Rane and Reloop, and can be adjusted to different device sizes using the included foam strips. Crafted from 9 mm vinyl laminated plywood, sturdy aluminum profiles, heavy duty butterfly latches and smooth rolling wheels, this case provides ultimate protection for mobile use on the road.

Fits

Pioneer DJM-V10
Pioneer DJM-A9
Pioneer DJM-900 NXS2
Pioneer DJM-900 NXS / SRT
Pioneer DJM-800 / 700 / 600
Pioneer CDJ-3000
Pioneer CDJ-2000 NXS2
Pioneer CDJ-2000 NXS
Pioneer CDJ-900 / 850 / 800
Pioneer XDJ-1000
Allen & Heath PX5
Allen & Heath DB4
Allen & Heath DB2
Allen & Heath Xone 92 / 62 / 43C
Denon LC 6000 Prime
Denon SC-6000 / SC-6000M
Denon SC-5000 / SC-5000M
Denon X1850 / X1800
Denon X1600
Denon SC3900
Denon SC2900
Reloop RMX-90 DVS
Reloop RMX-80 Digital
Ecler Warm 4
Ecler NUO4
Rane MP2015
Rane Sixty-Eight / Sixty-Four

Specs

Outer measures: 125,4 x 59 x 25 cm
Inner measures: 33,1 x 42,5 x 8,4 cm / (CDJ compartment) 43,7 x 45,4 x 8,4 cm (Mixer compartment)
Weight: 21,5 kg

Notes: UDG have further fine-tuned what was already a great design concept of a flight case into one especially for the most discerning DJ/producer. Constructed from solid 9mm thick plywood, the outside is laminated in a black finished honeycomb/hexagonal "Stage Grip" pattern. The inner sides are protected with high density diamond embossed EVA foam protective padding. This extremely robust padding protects the equipment against scratches, dust or other damages, creating a unique stylish & practical finish.

Extra wide black finished aluminium profile & massive UDG logo embossed ball corners are incorporated to ensures longevity & maintaining a permanently attractive, professional design. The UDG Ultimate Flight Case Pioneer DDJ-REV5 Black Plus (Laptop Shelf) also features heavy-duty spring-loaded handles for a secured lift & load.

UDG Ultimate Flight Case Pioneer DDJ-REV5 Black Plus (Laptop Shelf) not only transport your complete set up easily & securely, but also facilitates devices to be setup within minutes. With these premium features incorporated, the UDG Ultimate Flight cases provide premium professional quality in a very stylish modern black coloured combination.

Specifications

Colour: Black
Weight: 15,80 kg / 34.76 lbs
Outer Dimensions (W x H x D): 84.4 x 51.5 x 24.3 cm | 33.2 x 20.3 x 9.5 inch
Inner Dimensions (W x H x D): 73.8 x 36.2 x 5.5 cm | 29.1 x 14.3 x 2.2 inch
Material: Heavy duty construction of 9 mm thick plywood

Protection:

Improved powder coated and anodized hardware
High density diamond embossed EVA foam & carpeted protective padding
Dual anchor rivets with included washer
Extra-wide black solid aluminium profiles
Secure stacking due to stackable ball corner

Extras

Convenient 80 mm space at rear for connections & PSU storage
Adjustable laptop shelf
UDG heavy-duty spring-loaded handles
Cable access hole with removable UDG emblem cover
Removable front access panel

Fits

Pioneer DDJ-REV5 controller

Notes: UDG have further fine-tuned what was already a great design concept of a flight case into one especially for the most discerning DJ/producer. Constructed from solid 9mm thick plywood, the outside is laminated in a black finished honeycomb/hexagonal "Stage Grip" pattern. The inner sides are protected with high density diamond embossed EVA foam protective padding. This extremely robust padding protects the equipment against scratches, dust or other damages, creating a unique stylish & practical finish.

Extra wide black finished aluminium profile & massive UDG logo embossed ball corners are incorporated to ensures longevity & maintaining a permanently attractive, professional design. The UDG Ultimate Flight Case Pioneer PLX-CRSS12 Black also features heavy-duty, spring-loaded handles for a secured lift & load.

UDG Ultimate Flight Case Pioneer PLX-CRSS12 Black not only transport your complete set up easily & securely, but also facilitates devices to be setup within minutes. With these premium features incorporated, the UDG Ultimate Flight cases provide premium professional quality in a very stylish modern black coloured combination.

Specifications

Colour: Black
Weight: 9,00 kg / 19.8 lbs
Outer Dimensions (W x H x D): 51.1 x 42.6 x 23.0 cm | 20.1 x 16.7 x 9.1 inch
Inner Dimensions (W x H x D): 45.6 x 38.6 x 7.8 cm | 17.9 x 15.2 x 3.1 inch
Material: Heavy duty construction of 9 mm thick plywood

Protection:

Improved powder coated and anodized hardware
High density diamond embossed EVA foam & carpeted protective padding
Dual anchor rivets with included washer
Extra-wide black solid aluminium profiles
Secure stacking due to stackable ball corner

Extras

Convenient 80 mm space at rear for connections & PSU storage
Right & left side removable access panel
UDG heavy-duty spring-loaded handles
Cable access hole with removable UDG emblem cover

Fits

Pioneer PLX-CRSS12 turntable

Notes: Really smart integration of macro controls for Eurorack, based on the original design by Emblematic Systems. Assign settings to eight CV outputs then morph with the crossfader or record movements to manage presets or set up complex real-time modulation. Can also operate as Catalyst Sequencer.

Supplier's Notes:
The Catalyst Controller is a macro controller with eight precision CV outputs and a responsive crossfader to morph between scenes. A scene is a snapshot of up to eight CV outputs, like a modular preset. Traverse a "pathway" composed of multiple scenes using the crossfader or an external CV signal, or immediately jump using the scene buttons. Record CV and slider movements, and play recordings back via a button or external trigger.

Each output has sub-millivolt precision and a maximum range of -5V to +10V. Channels have an adjustable morphing curve, can be quantized to common scales, restricted to a particular voltage range, or set to output gates.

Whether used as a CV preset manager, seamless transition generator, chord sequencer, CV recorder, or experimental CV playground, the Catalyst Controller puts control of your modular at your fingertips.

The Catalyst Controller can also turn into a Catalyst Sequencer! Hold down a special button combination to change between controller and sequencer modes. If you end up liking the Sequencer more, you can even remove the double-sided faceplate, flip it over, and re-install with the Sequencer artwork visible.

Based on the original Catalyst module from Emblematic Systems.

Specifications:

Smooth, responsive crossfade morphs between scenes
Eight output channels, each can be CV or Gate
Arrange scenes into pathways of up to 64 scenes
Smooth, responsive crossfader morphs from scene to scene along the pathway
Set slew/lag to limit how fast scenes can change
Adjustable Morph time per output
Control crossfading with an external CV
Record and playback up to 20 seconds of CV and crossfader motion
CV outputs can be set to -5V to +10V maximum, or limited to +/-5V, +5V, +3V, or +1V
CV outputs can be unquantized (sub-1mV resolution), or Quantized to common scales
Randomization of channel values/gates
Copy/paste
Based on the original Catalyst from Emblematic Systems

Pairs with: 4ms Catalyst Sequencer

Notes: Neatly implemented performance mixer with four stereo channels. CV control of level and pan, two pre- or post-fader stereo send busses, quiet mutes and cueing via a front-panel headphone socket.

Supplier's Notes:
Four channel stereo production mixer

Mixer section

Each channel has the following:

Stereo or mono - Each channel can be treated as a stereo channel or a mono channel with two summed inputs.

CV inputs for both panning and level control

Two send buses - You can route each channel to one of two send buses. Each send bus is stereo. You can choose if you want the send to come before or after the level/panning controls.

Mute - The mute has both latching mute (up) and a momentary mute (down). The mute uses a capacitor to slow the turn off and on of the mute action. So it is mostly click-less, but you may find an occasional pop.

Cue bus - You can route each channel to the cue bus.

Mains Section

Two stereo sends outputs
Two stereo returns - which can also be used to directly insert into the main mix.
Main stereo outputs - level controlled with the slider and stereo VU meter.
Main mono output - summed output of the main L&R. If you are after an 8ch mono mix, you can use each channel in stereo mode, use the level control to control the level and then pan control to control the levels of the two channels.

Cue Section

1/4" Headphone jack along with level control
Fader control to listen to the main mix, cue mix, or an adjustable mix of the two.
Expandable

Bartenders can be cascaded to create 8ch, 12ch, or 16ch mixer. The main level is what is sent the main level control can act as a group control.

Barbacks can be added to add 2ch to your mix. Barbacks can also be cascaded enabling up to a 16ch mixer configuration.

Send-VCA can be added for CV control of the level of the send.

DVCA, Cast Iron, Mingles, and USB-2CH can all be connected with Dupont cables (aka female to female breadboard cables) via pin headers on the back of the modules. Connecting the in and out pins will send/receive the audio into the next module.

Width: 24hp
12V: 260mA
-12V: 225mA

Notes: A simple VC panner with CV-controlled level. The left input normals to the right input to give an easy way to add panning to a mono signal.

Expandable

Bartender, Barbacks, DVCA, Cast Iron, Mingles, and USB-2CH can all be connected with Dupont cables (aka female to female breadboard cables) via pin headers on the back of the modules. Connecting the in and out pins will send/receive the audio into the next module.

Width: 4hp
12V: 40mA
-12V: 40mA

Notes: Dual three channel voltage controlled panning mixer

Mixer section

Channel 1 and Channel 2 are three channel mixers with potentiometers to control level of three different inputs for each channel. Each channel then has a potentiometer to control panning as well as CV control for panning and level control

Panning and VCA

The VC panners are equal loudness panning and the VCAs for each channel are linear response.

Built-in LFO

There is a built-in LFO that is normalled to the panning CV input of each channel. CH1 gets the standard LFO and CH2 gets an inverse, enabling alternating channel panning. The default is to use a TRI wave for the LFO, but there is a jumper on the back to switch it to SQU.

Width: 12hp
12V: 140mA
-12V: 120mA

Notes: This is an expander for Bartender and Barback, enabling CV control of the level of the send bus of up to 8 channels.

Each section of four jacks has a cable to connect to the mixer modules. To get 4 channels to work with Barback you want to connect it to the last Barback in the chain of two. It will then pass along channels 3 & 4 to the next Barback.

Dimensions
2 HP

Current Draw
Module does not draw current

Notes: Two channel USB module.

Standard Mode - Send two channels into your USB device and receive two channels from USB.

Insert Mode - Send two channels to your USB device and get a copy of the sent signal in the outputs.

Toggle between the modes via a pair of jumpers on the back. The USB-B to USB-A cable is provided with the module. Why use the cutting edge USB-B? I felt the jacks were way more sturdy than mounting USB-C jacks vertically.

Expandable - Bartender, Barbacks, DVCA, Cast Iron, Mingles, and USB-2CH can all be connected with Dupont cables (aka female to female breadboard cables) via pin headers on the back of the modules. Connecting the in and out pins will send/receive the audio into the next module.

Width: 4HP
12V: 10mA
-12V: 10mA

Notes: Premium Inner Record Sleeves - Master Sleeves for 12" Records
We think protecting your vinyl records with the highest-quality sleeves results in the best sound. Our premium master record sleeves help you avoid scuffing, static, and hairline scratches on your records.

Premium 3-ply polyethylene record inner sleeves add an extra line of defense and quality to your collection, preserving great music for decades to come by repelling dust for "long play" protection.

Why Add a Rice Paper Layer?
These archival record sleeves are made from high-density polyethylene (HDPE) with a rice paper backing. The rice paper layer is sandwiched between two sheets of HDPE with a translucent HDPE front. You'll find many records in their premium master sleeve, still in perfect condition decades later. This construction has other benefits, too:

No risk of paper scuffs
Reduction in static
Lower risk of sticking to vinyl over time
True collectors know that the quality and reliability of master sleeves aren't easy to find in your typical paper sleeve cover. Our clear vinyl record inner sleeves provide easy viewing of each record you pull. Premium anti-static record sleeves contain a transparent side for easy viewing of your complete album.

Notes: Blank Album Jackets, White, 20x 12 Inch LP Vinyl Covers

Vinyl Is Forever

... That is if you take good care of it! Big Fudge is the leading brand in the protection, storage, and display of vinyl records - like this set of 20 Glossy Black Album Covers!

It's Time to Replace Those Sad Old Vinyl Jackets

You, and those who came before you, loved those albums so HARD the jackets are now tattered. So replace them with blank album covers that let you spend less time with the sticky tape and more time listening to perfectly protected tunes. Unlike other jackets with thin spines that bunch up your sleeves, these jackets let you write ON the spine and keep the sleeves smooth and flat.

20 Blank Jackets for 12" Vinyl
350gsm Thick Glossy White Cardboard - Acid-Free
Compatible With Standard 12" Inner and Outer Sleeves
3.5mm Spine To Label Your Albums with Thin Chalk Market

Fits Your Favourite Sleeves

These Covers fit 12" albums like a hug from Tony Bennett. Some jackets make inner sleeves bunch up, but Big Fudge covers let plastic or paper sleeves slide in like a dream and then fit snugly to prevent them from falling out.

Add Your Artwork

Thin spines are annoying. But these jackets have a 3.5 mm thick spine, so you can label it. The front lets you glue or sticker art and then slide it into your outer sleeve. Use thin chalk markers that require a solvent to remove.

20x black Jackets

Your order includes 20 vinyl covers. Acid-free, 350 gsm glossy black cardboard jackets with the same quality you expect from Big Fudge. These will fit all your vinyl, even 180g pressings.

They've Had a Hard Life

You've dragged them around town, listened to them a million times, or found them already pre-loved and worn-out; now give them a new start at life with these Album Covers from Big Fudge - the brand that thousands of vinyl fans love and trust.

Notes: Gatefold Record Sleeves

Enjoy True Gatefold Protection Without Restriction

Make sure your collection of prized gatefold albums is set up for long-term enjoyment with gatefold record sleeves. These archival-quality and acid-free vinyl gatefold sleeves protect your records with the same level of quality as traditional and premium record sleeves but have been designed to store your gatefolds. Designed for ease of use in accessing your albums, there is no need to get caught up in the packaging. Stop fumbling around with other outer sleeves and go full gatefold! You'll enjoy a sleek and streamlined design with crystal-clear covers, keeping your collection looking stunning for years to come. Album artwork shines through with zero frosting.

Preserve Your Collectible Albums with Big Fudge

Gatefold records are known to have some of the most appreciated artwork with their additional space. These were designed for you to be able to keep this artwork intact and display these favourites with pride. Big Fudge's gatefold record sleeves are sized with care and designed with record display in mind with non-crimping materials and 3mil of crystal clear polyethylene that keeps your gatefold records' artwork popping and the records looking brand new. As record collectors with the goal of helping other record collectors, these gatefold record sleeves will be just the thing to take your gatefold records to the next level and keep them pristine.

Product Information:

25.5" unfolded, with 2 pockets 12.75in square
25 Crystal Clear Outer Sleeves
Fits all standard and oversized 12" gatefold albums

Notes: Blank Album Jackets, Black, 20x 7 Inch Single Vinyl Covers

Vinyl Is Forever
... That is if you take good care of it! Big Fudge is the leading brand in the protection, storage, and display of vinyl records

It's Time to Replace Those Sad Old Vinyl Jackets
You, and those who came before you, loved those albums so HARD the jackets are now tattered. So replace them with blank album covers that let you spend less time with the sticky tape and more time listening to perfectly protected tunes. Unlike other jackets with thin spines that bunch up your sleeves, these jackets let you write ON the spine and keep the sleeves smooth and flat.

20 Blank Jackets for 7" Vinyl
350gsm Thick Glossy Black Cardboard - Acid-Free
Compatible With Standard 7" Inner and Outer Sleeves
3.5mm Spine To Label Your Albums with Thin Chalk Market

Fits Your Favorite Sleeves
Our Black Covers fit 7" records like a hug from Tony Bennet. Some jackets make inner sleeves bunch up, but Big Fudge covers let plastic or paper sleeves slide in like a dream and then fit snugly to prevent them from falling out.

Add Your Artwork
Thin spines are annoying. But our jackets have a 3.5 mm thick spine, so you can label it. The front lets you glue or sticker art and then slide it into your outer sleeve. Use thin chalk markers that require a solvent to remove.

They've Had a Hard Life
You've dragged them around town, listened to them a million times, or found them already pre-loved and worn-out; now give them a new start at life with our Black and White Album Covers from Big Fudge - the brand that thousands of vinyl fans love and trust.

Notes: Blank Album Jackets, White, 20x 7 Inch LP Vinyl Covers

Vinyl Is Forever

That is if you take good care of it! Big Fudge is the leading brand in the protection, storage, and display of vinyl records - like this set of 20 Glossy White Album Covers!

It's Time to Replace Those Sad Old Vinyl Jackets

You, and those who came before you, loved those albums so HARD the jackets are now tattered. So replace them with blank album covers that let you spend less time with the sticky tape and more time listening to perfectly protected tunes. Unlike other jackets with thin spines that bunch up your sleeves, these jackets let you write ON the spine and keep the sleeves smooth and flat.

20 Blank Jackets for 7" Vinyl
350gsm Thick Glossy White Cardboard - Acid-Free
Compatible With Standard 7" Inner and Outer Sleeves
3.5mm Spine To Label Your Albums with Thin Chalk Market

Fits Your Favourite Sleeves

These White Covers fit 7" records like a hug from Tony Bennet. Some jackets make inner sleeves bunch up, but Big Fudge covers let plastic or paper sleeves slide in like a dream and then fit snugly to prevent them from falling out.

Add Your Artwork

Thin spines are annoying. But these jackets have a 3.5 mm thick spine, so you can label it. The front lets you glue or sticker art and then slide it into your outer sleeve. Use thin chalk markers that require a solvent to remove.

Your order includes 20 vinyl covers. Acid-free, 350 gsm glossy white cardboard jackets with the same quality you expect from Big Fudge. These will fit all your vinyl, even 180g pressings.

They've Had a Hard Life

You've dragged them around town, listened to them a million times, or found them already pre-loved and worn-out; now give them a new start at life with Big Fudge's Black and White Album Covers from Big Fudge - the brand that thousands of vinyl fans love and trust.

Notes: Black Special Edition Inner Sleeves | Made from Heavyweight & Acid Free Paper

Black Inner Record Sleeves

Protect Your Record Collection in Style with Black Inner Sleeves

As record aficionados themselves, Big Fudge knows how crucial record collection maintenance is in order to preserve your vinyl's quality and longevity. When you love a record dearly it's only natural that with enough rotations that the cover and sleeves will begin to fold and flap obnoxiously. Add a stylish flair to your records with our new black inner sleeves. These have a sleek and stylish design while preserving your favorite music at the same time.

Contemporary Storage Solutions for Your Classic Albums

Big Fudge provides unrivaled protection for your record collection. Enjoy the matte black design with thick protection from daily wear and tear. Protecting and collecting your records is simple with black inner sleeves that are made to help you enjoy your records for decades.

Notes: Vinyl Record Inner Record Sleeves - Acid-Free Paper & Round Corners

Vinyl Collector Basics Done Right

Big Fudge premium vinyl record inner sleeves are made from bright white, heavyweight paper (20 lbs) that is both acid and alkaline-free. Designed by collectors for collectors, these sleeves feature exterior seams instead of interior seams, making it easier to slide your records in without wearing down the sleeve. Big Fudge also use rounded corners instead of square corners to ensure a perfect fit in any album cover. There'll be no more scuffing, static build-up, or dust.

Elevate Your Vinyl Experience

For the avid collector, vinyl records are more than just a medium for music - they're a piece of history, a nod to the bygone era, and an investment for the future. That's why Big Fudge have curated a range of tools to protect and preserve the original quality and soul of your collection, including these acid-free paper record sleeves. Big Fudge's range of outer and inner vinyl sleeves, jackets, and cleaning kits ensure that your vinyl remains as pristine as the day it was pressed.

Investing in these products is investing in the longevity of your collection. With Big Fudge, you're not just buying protection; you're ensuring the legacy of your music lasts for generations to come. Join the community of collectors who trust us with their most cherished possessions.

The aim is make it easy to find everything you need to clean your records and keep them that way. Use these vinyl inner sleeves as a first line of defence, Big Fudge's popular outer sleeves as the second line of defence, and Big Fudge's 4-in-1 cleaning kit or Record Friend to battle any dirt or grime that manages to stick to your records during use.

The goal is to provide audiophiles with vinyl record care tools that go above and beyond, heightening the quality of your records with ease. Please contact us for questions about your order or any other questions you might have.

They've Had a Hard Life

You've dragged them around town, listened to them a million times, or found them already pre-loved and worn-out; now give them a new start at life with Big Fudge's Black and White Album Covers from Big Fudge - the brand that thousands of vinyl fans love and trust.

Notes: Whether we're talking cleaning or storage, it's important to maintain your vinyl collection in unmarred, scratch-free condition. But running around stocking up on supplies is time-consuming and takes you away from what you would rather be doing: listening to tunes. That's why Big Fudge are excited to offer vinyl album sleeves and inner LP sleeves in a single package. Keep your vinyl in mint condition at a reasonable price.

Get 50 Crystal-Clear Outer Sleeves: Show Off Your Album Art

These outer sleeves fit all 7" records, including most double albums and gatefolds, with less excess than other vinyl sleeves, which allows just enough room to breathe. Big Fudge use 3mil, crystal-clear polypropylene so that the album artwork is easy to see and the albums don't stick together.

Get 50 Acid-Free Inner Sleeves: Protect Your Vinyl

The custom rounded corners on these inner LP sleeves allow you to slide them into and out of even the most loved covers with ease, while the specially placed external seams allow you to slide vinyl in and out without snagging.

Notes: Outer Sleeves - 3 mil HDPP, Crystal Clear, Wrinkle-Free

Beautiful Heavy-Duty Protection

Vinyl record outer sleeves by Big Fudge are made from durable, crystal clear high-density polypropylene. Unlike industry-standard polyethylene record sleeves, which are opaque and easily clouded, our outer sleeves allow your album art to stand out and last longer.

Like all our other products, our outer record sleeves are designed by record geeks who want to make products worthy of their own standards. Other protective covers may split at the seams or wrinkle, but our sleeves are designed to forego all of those issues. These clear vinyl sleeves will fit both single LPs comfortably and accommodate your prized gatefold or double albums snugly. Big Fudge have streamlined the vinyl outer sleeve design further by removing the bulk that resealable flaps cause in other brands' sleeve styles.

These vinyl record outer sleeves will fit single records, gatefold, or double albums comfortably.

Notes: Neat little interface module to help pad controllers play nicely with Eurorack. Hook up a device like a Launchpad or APC and jam out rhythms with retriggering options, dynamic control and MIDI sync.

Supplier's Notes:
Triggerpad is a dynamic trigger/gate sequencer in eurorack format on only 6hp. A USB MIDI controller with an 8×8 grid like Launchpad or APC is used to display and edit the patterns (see the list of compatible controllers). The user experience is tailored to live performance and detailed composition: dial in simple rhythms or complex polyrhythms, retrigger at audio rate, create dynamic percussions with velocity triggers or use longer pulses to create steppy modulations.

By using USB MIDI controllers that you might already have and maybe not use anymore, we avoid producing more plastic. Give your old gear a second life!

Dimensions & consumption

Width: 6hp
Depth: 39mm
+12V: 120mA (without USB MIDI controller connected)
-12V: 20mA
5V: 0mA
USB MIDI controllers consume up to 150mA on +12V

Connectivity

8 dynamic trigger/gate outputs (0-10V)
USB MIDI Host
Clock in
Clock out
Reset in
Reset out

Compatibility

Launchpad Pro Mk3
Launchpad X
Launchpad Mini Mk3
Launchpad Mini Mk2
Launchpad Pro
Launchpad Mk2
Launchpad S
APC Mini Mk1
APC Mini Mk2

Notes: TRS Split - CV/Audio signal distributor

TRS Split is a multipurpose CV and audio signal distribution module. It has three 3.5 mm TRS (tip/ring/sleeve - stereo) jacks and six ordinary 3.5 mm mono jacks.

It contains 3 identical sections set up as following:

Upper jack carries the tip signal
Middle jack carries the stereo/dual signal
Lower jack carries the ring signal

Each section can either split a stereo signal into two mono signals or join two mono signals into one stereo signal. The module does not have any active components and does not need a power supply.

Use cases:

When you plug a stereo signal carried by a stereo (TRS) cable into the middle jack, you receive two separate mono signals by plugging in a mono (TS) cable in the upper jack to carry the left signal and a mono (TS) cable in the lower jack to carry the right signal. That way you can attack an "AUX" cable such as from your smartphone to your modular.

Or the other way around: Send two separate mono signals by plugging in a mono (TS) cable in the upper jack to carry the left signal and a mono (TS) cable in the lower jack to carry the right signal. Receive a stereo signal at the middle jack to be used with a stereo (TRS) cable.

Converting from stereo to dual mono and back allows you to alter the two sides of a stereo signal with different effects/filters.

Some tuners such as the Korg NTS-2 accept inputs to tune two oscillators combined in one 3.5 mm stereo jack. With one splitter you can easily feed two VCO signals into such a tuner.

Switching sides

Two splitters can be used to switch tip and ring (left and right): Plug in a stereo cable in the middle jack of the first section. Connect mono cables to the upper and lower jack of the first section. Then connect the upper mono cable of the first section to the lower mono jack of the second section and the lower mono cable of the first section to the upper mono jack of the second section. The signals are switched. Plug a stereo cable in the middle of the second splitter and you're good to go.

Hint: This also works for MIDI signals. If you use MIDI over minijack, there are two standards A and B - some manufacturers use A some B - thus not all connections are working. Now you can easily switch between the standards using the TRS Split.

Note: The MIDI input of the DROID X7 automatically detects A and B, so there is no switching necessary. The MIDI output of the X7 can be set to A or B with a switch on the back of the module.

Stereo multiple setup

If you have a separate multiple in your modular, you can use the TRS-SPLIT to create a 1:2 stereo multiple as follows:

Plug a stereo cable in the middle jack of section 1, patch the mono cable from the upper jack into section 1 of your multiple (e.g. a 3/3/3 multiple) and feed two of the outputs back into the upper jacks of section 2 and 3. Do the same with the mono cable coming from the lower jack of section 1 going into the second section of a 3/3/3 multiple and patch two cables back into the lower jacks of section 2 and 3 of the TRS Split. Now the middle jacks of section 2 and 3 both carry the stereo signal.

Dimensions
2 HP
22 mm deep

Current Draw
Module does not draw current

Notes: TRS Tool - Stereo/Dual CV/Audio/MIDI signal multipurpose module

TRS Tool is a multipurpose CV and audio signal distribution module for working with 3.5 mm stereo jacks (tip/ring/sleeve). These jacks are common for stereo audio but also for MIDI.

The TRS TOOL has no active components and does not need a power supply. It contains 3 different sections set up as following from top to bottom:

TRS Split
The upper jack carries the tip signal
The middle jack carries the stereo/dual signal
The Lower jack carries the ring signal

Use cases:

When you plug a stereo signal carried by a stereo (TRS) cable into the middle jack, you receive two separate mono signals by plugging in a mono (TS) cable in the upper jack to carry the left signal and a mono (TS) cable in the lower jack to carry the right signal. That way you can attack an "AUX" cable such as from your smartphone to your modular.

Or the other way around: Send two separate mono signals by plugging in a mono (TS) cable in the upper jack to carry the left signal and a mono (TS) cable in the lower jack to carry the right signal. Receive a stereo signal at the middle jack to be used with a stereo (TRS) cable.

Converting from stereo to dual mono and back allows you to alter the two sides of a stereo signal with different effects/filters.

Some tuners such as the Korg NTS-2 accept inputs to tune two oscillators combined in one 3.5 mm stereo jack. With one splitter you can easily feed two VCO signals into such a tuner.

TRS Quad Multiple

Multiply a stereo signal. Four TRS jacks to be used with stereo minijack cables.

Use cases:

You could use this to multiply the signal for headphones - listen to patches together.

Or create sends - route one (or two) stereo signals to effects and use the third one as dry signal going to the mixer.

Experimental: multiply a MIDI signal to two or three receivers: NOTE: depending on the output power of the MIDI sender and the power draw of the MIDI receivers this might or might not work. MIDI uses a current of typically 5 mA instead of voltage levels for data transmission. So when you attach too many devices to one output the current might not be enough to drive all of them. So this is strictly spoken not covered by the MIDI standard, but might work anyway.

A/B Swapper
The bottom section of the module consists of two connected TRS jacks.
Whatever signal applies to the tip in jack A will be routed to the ring in jack B.
Whatever signal applies to the ring in jack A will be routed to the tip in jack B.

Use cases:

Switch the left and right side of a stereo audio signal.

Switch between MIDI standard A and B: If you use MIDI over minijack, there's two standards A and B - some manufacturers use A some B - thus not all connections are working. Now you can easily switch between the standards using the TRS Split.

Note: The MIDI input of the DROID X7 automatically detects A and B, so there is no switching necessary. The MIDI output of the X7 can be set to A or B with a switch on the back of the module.

Dimensions
2 HP
22 mm deep

Current Draw
Module does not draw current

Notes: The "uMM" combines a MIDI merger and two independent THRU distributors in a module that is only 4 HP wide. All sockets on the module are in MIDI TRS-B format.

At the heart of the two-input MIDI merger is a small, powerful ARM processor with plenty of buffer memory. Two MIDI streams are mixed to one output and can also be tapped via an additional second output. Two LEDs signal the operation of the merger: one LED indicates MIDI activity at the inputs, and a second LED warns of too much data at the inputs.

The second group of functions consists of two independent, separate MIDI THRU distributors. The MIDI data at the respective MIDI input can be picked up and distributed at the three THRU outputs. If required, a 1-to-5 distributor can be created from the two units by connecting an output of the left group to the input of the right group.

Features:

4x MIDI IN (TRS-B)
2x MIDI-OUT (TRS-B)
6x MIDI-THRU (TRS-B)
Powered via Doepfer connector

Notes: Advanced generative sequencer featuring mutes per channel and transposition facilities.

Akropoli is an extension and enhancement of our successful Little Melody and High Towers modules, offering the features of both of these modules as well as some of it's own unique features such as mute buttons per channel, manual transpose knob and 1V/oct transpose CV input. Akropoli operates using Frequency Central's proprietary TOOL V2 code, and can count in integers as well as multiples for even more subtle and evolving variations.

Akropoli is a generative sequencer based around clock divisions and a chromatic quantiser, used to create in-the-moment licks and riffs. It is more that the sum of it's parts.

Akropoli's internal operations can be considered as 4 clock dividers patched into a CV mixer via attenuators. The attenuators select notes over a 5 octave range, the clock dividers determine how often those notes are added to the mix. The final output of Akropoli is quantized chromatically for fast set up and continuously pleasing results. Akropoli has an onboard transposition knob, as well as a 1V/oct transposition CV input.

The 4 clock dividers are labelled A, B, C, and D. They all receive clocks from the same source, the divisions may be selected using the presets and the individual division selectors. The clock dividers can be set to count up, down, or to one of a variety of modes that move between counting up and down. For further information on Presets and Modes see the Little Melody User Guide.

Additionally, each clock divider has it's own binary output (either high or low), these 4 outputs can be used to clock/gate/trigger other stuff on other modules to great effect.

Product Specifications

12V draw
50mA

-12V draw
36mA

5V draw
0mA

Depth
35mm

Notes: Ideal for protective archiving. White protective sleeve with transparent viewing window. Hole punches on both sides.

Found an epic record by the Rolling Stones at the flea market? Unfortunately the album cover is totally ragged or maybe even doesn't exist any more. Buy the LP anyway, and with it the outer sleeves from Hama so that the record is protected even without its original cover.

Material: Paper
Model: Protective Cover

Field of Application

For Medium: LP
Suitable for: Universally Usable

More product information

Ideal for protective archiving
White protective sleeve with transparent viewing window
Hole punches on both sides

Technical Details

Material: Foil Model
Protective Cover Depth: 0.3 cm
Height: 30.5 cm
Width: 30.3 cm
Colour: White.
Pack of 10 sleeves.

Notes: Fade between two signals with the fader, just as nature intended

Do you have aspirations to smoothly fade between two signals? The Herzlich Crossfade lets you do exactly that, and exactly nothing else, using well-designed active circuitry and a smooth and performance friendly sliding potentiometer.

Whatever your aspirations are, this crossfader lets you live out your crossfading dreams in the simplest possible way, with not a fraction of an inch wasted on unnecessary features. Only delightful build quality and pleasantly smooth crossfading lies ahead for you.

Dimensions: 2 HP

Notes: Two bipolar LEDs allow you to visualize your voltages as they swing between positive and negative, as well as their level of intensity, without affecting the signal you input.

Think of it as a 1D oscilloscope in just 2hp! An easy way to grasp what your patch is currently doing, without sacrificing the money or space on more fully-fledged solutions. Useful as part of a patch to keep track of your oscillations, as a troubleshooting device to quickly verify that something is doing what it should be doing, or simply as a healthy dose of blinkenlights in addition to your existing array of sparkling LED pleasures. Best of all? You get two in just 2hp - you'll have to spend some serious cash to get that kind of function-per-hp density anywhere else!

Dimensions: 2 HP

Notes: Bartender? The power of gate signals at the touch of a button, please - but make mine a narrow one!

You already know what this is: it's a gate signal generator, and it generates gate signals. That's all there is to it. You press the button, the LED indicator lights up, and you get a 5v gate signal! Brilliant!

You get three, in just 2hp! That's 1 1/2 gate signal generators per hp! That's more than [competing product] from [competing brand]! You knew you made a good decision when you decided to look at this product.

All that remains now is to open your heart, and your wallet. Buy this gate generator - this version is the latching model (stays on or off after pressing). In fact, it works really well with the Quad Gate to Trigger Converter, also from Herzlich Labs - now you can generate both gates and triggers with ease! And in such little hp!

Oh, one more thing? Your friends are going to be very envious of this, when you show it off. Gold plated nuts, gold plated front panel, tastefully matte indicator LEDs, pleasantly tactile buttons, black hardware. All the details have received the closest care and attention.

Dimensions: 2 HP

Notes: Bartender? The power of gate signals at the touch of a button, please - but make mine a narrow one!

You already know what this is: it's a gate signal generator, and it generates gate signals. That's all there is to it. You press the button, the LED indicator lights up, and you get a 5v gate signal! Brilliant!

You get three, in just 2hp! That's 1 1/2 gate signal generators per hp! That's more than [competing product] from [competing brand]! You knew you made a good decision when you decided to look at this product.

All that remains now is to open your heart, and your wallet. Buy this gate generator - this is the momentary model (is normally off, and temporarily on when you press it). In fact, this also works really well with the Quad Gate to Trigger Converter, also from Herzlich Labs - now you can generate both gates and triggers with ease! And in such little hp!

Oh, one more thing? Your friends are going to be very envious of this, when you show it off. Gold plated nuts, gold plated front panel, tastefully matte indicator LEDs, pleasantly tactile buttons, black hardware. All the details have received the closest care and attention.

Dimensions: 2 HP

Notes: Drawing inspiration from the MMI Maxima, the MMI Helios is intended as a middle ground between the gestural control surface of the Maxima and the fingertip control of the smaller MMI.

Less density, but a much higher degree of patch control is the key point of the Helios, which complements other MMI devices very well, and can be joined with other Helios (Helii?) to form larger and creative control surfaces.

The design is greatly simplified compared to the original MMI, with only two I/O jacks - either can function as input and output, and their interaction with each other is determined by touching both plates simultaneously to form a connection, or in cooperation with other MMI devices.

Available in a "right" and "left" version - one is an exact mirror image of the other, which makes it suitable for having two units adjacent to one another.

Dimensions: 8 HP

***Please note: the "righthand" version is not included, it is shown in the picture for demonstration purposes only. ***

Notes: Beauty. Refinement. Attenuversion.

It's another Herzlich Labs release: the 2hp stereo Attenuverter. Two channels of connected attenuversion, allowing you to fully and smoothly invert any signals you plug in - turn negative to positive, turn phase to antiphase, and find all the variations in between.

With the usual pleasantly tactile sliding pot, the sAttenuverter is both performance friendly and inspiring to use. Extremely suitable for linked mono signals and stereo alike, it will feel right at home in the increasingly popular stereo setups in modular.

Dimension: 2 HP

Notes: Need an offset voltage? Of course you do, you probably need one all the time, and you can never seem to find one. Well, here's two.

Yes, the Stereo Offset boasts not one but TWO linked offset voltages, and even better, they can be independently set as unipolar or bipolar with jumpers on the back of the module. To further aid your adventure in offsetting, bicolor LEDs will indicate the current state of both outputs.

Smoothly transition between voltages to simultaneously control other functions in your system, either by applying identical voltages to two different places, or by using simultaneous unipolar and bipolar signals for advanced control over your Eurorack system.

Do the right thing - get an offset generator you will love.

Dimensions: 2 HP

Notes: Long-awaited update of Jomox's unique take on filtering, step sequencing and effects. Touchpad programming, CV control and deep MIDI integration make the MoonWind a powerful all-rounder.

Supplier's Notes:
Almost 12 years ago, Jomox brought out the first Moonwind. Now it's about time for an improved successor with OLED display, touch pad and more buttons for instant access.

Moonwind MkII is a true analogue stereo filter with built-in step sequencer, a fantastic sounding digital FX chip, two LFOs, VCA, two ADSR envelopes and envelope follower modulation.
Fixed CV in- and outputs and 6 assignable CVs make the Moonwind Mk II a versatile choice even in eurorack environment.

Everything is storable and controllable via Midi.

You can play the Moonwind Mk II like a synth by Midi notes and play melodies on the filters if they whistle in self-resonant mode.

The sequencer is able to control cutoff, Q and resonance per step and filter and thus turns the stereo filter with analogue fed back effects into a creative instrument of its own.

The editing of sequences can also be made via touchpad:

This makes the Moonwind Mk II an easy-to-use and awesome analogue sounding engine that is playable like a synth and can be seamlessly integrated into a DAW recording system

Specifications

Two real analogue low noise multimode filters
OTA technology *
Per filter Q (narrowness) and Resonance are separately adjustable **
Per filter the shapes lowpass, highpass, bandpass and notch are assignable
The filters are connectable among each other***
Per filter there is one LFO with 64 waveforms which controls the cutoff
Per filter there is envelope amount, the envelope is created from the audio with an analogue envelope follower
2 ADSR envelopes for filter and VCA that are triggered via Midi
Inputs are Hi-Z and can amplify guitar or bass signals directly
Touchpad for intuitive editing

2 CV outputs
3 fixed CV inputs
6 programmable CV inputs with amounts
Digital effects chip with 15 algorithms
Analog FX Feedback in order to create tape delays and wave guides
Three parameters per FX algorithm
The effects programs include chorus, flanger, tremolo, reverb, delay and some more exiting programs
Eight effects programs can be reloaded by OS update later on
Built-in noise generator with metallic noise and volume control
Sequencer can record Cutoff, Q and Res separately per step and filter
Maximum 64 steps per pattern
Maximum 32 steps per bar (then max. 2 bars), bars can be dynamically set according to the number of steps per bar
Clock divider can resolve max. 32th per bar
Record/undo function to record filter trails by the rotary knobs or touchpad
Direct Touchmode can record sequences with your fingertip
Sequencer and LFOs are midi clock synchronizeable
Midi notes control the cutoff of the filters, CCs the rest of parameters
Cutoff, Q and Resonance are made as classical potentiometers
Stable metal axis potentiometers and encoders with axle bearings
256x64 px LCD display
OS is updateable via Midi

Dimensions:

Width: 318mm
Depth: 180mm
Height front: 44mm
Height back: 72mm

Weight: 1.8kg

Notes: An ultra-compact 10HP VC filter with bags of personality. Camber can be treated as a subtle, non-intrusive sound design tool, or something much more lively.

Camber is designed to be a fun, tactile filter with a small footprint. It's sound is neutral enough for basic filtering without a fuss, with a much more aggressive tone available using high resonance settings in three-pole mode.

Filter Core

The core of the filter is based on a state variable topology using 2164 VCAs and 1% tolerance integrating capacitors. Resonance and feedback control is provided by the fantastic circuit design originally by Neil Johnson "Voltage Controlled 3-Pole State Variable Filter" recently made available in Sound Semiconductor documentation.

Operation

Camber is switchable between low pass and high pass responses with one pole (6dB) and three pole (18dB) flavours of each. It has full CV control of both cutoff frequency and resonance amount. The input is DC-coupled allowing LFO and CV signals to be routed through the filter. The filter will also act as a simple oscillator producing a clean sinusoidal signal with the resonance control turned *almost fully clockwise, and no signal at the audio input. Dialling in the resonance so that it is just under the point of self-oscillation allows the filter to be "Pinged" by sending gate signals to the audio input. This is useful for tuned percussion sounds and FX.

Specifications

Intellijel 1u format
Width 10HP
Depth 33mm
Power requirements ~40mA +12V/~40mA -12V
Control voltage range 0-8V
Impedance Input 100K / Output 1K

Notes: An ultra-compact 10HP VC filter with bags of personality. Camber can be treated as a subtle, non-intrusive sound design tool, or something much more lively.

Camber is designed to be a fun, tactile filter with a small footprint. It's sound is neutral enough for basic filtering without a fuss, with a much more aggressive tone available using high resonance settings in three-pole mode.

Filter Core

The core of the filter is based on a state variable topology using 2164 VCAs and 1% tolerance integrating capacitors. Resonance and feedback control is provided by the fantastic circuit design originally by Neil Johnson "Voltage Controlled 3-Pole State Variable Filter" recently made available in Sound Semiconductor documentation.

Operation

Camber is switchable between low pass and high pass responses with one pole (6dB) and three pole (18dB) flavours of each. It has full CV control of both cutoff frequency and resonance amount. The input is DC-coupled allowing LFO and CV signals to be routed through the filter. The filter will also act as a simple oscillator producing a clean sinusoidal signal with the resonance control turned *almost fully clockwise, and no signal at the audio input. Dialling in the resonance so that it is just under the point of self-oscillation allows the filter to be "Pinged" by sending gate signals to the audio input. This is useful for tuned percussion sounds and FX.

Specifications

Intellijel 1u format
Width 10HP
Depth 33mm
Power requirements ~40mA +12V/~40mA -12V
Control voltage range 0-8V
Impedance Input 100K / Output 1K

Notes: Lush analogue EQ switchable between tilt and Baxandall high-shelf configurations.

Perform a variety of mixing and sound design duties ranging from subtle brightness and clarity adjustments to low-end rumble removal, boosted low-pass filtering and sweep EQ.

In the default tilt mode, turning the control knob clockwise simultaneously boosts treble and cuts bass. Turning anti-clockwise boosts bass and cuts treble. These boosts and cuts are pivoted around the mid-range. With the control knob at 12 o'clock the frequency response is neutral.

With Baxandall high-shelf mode enabled, turning the control knob clockwise past 12 o'clock introduces and gentle high-shelf EQ weighted around the upper mid-range. Turning the control knob anti-clockwise results in a wide high-shelf cut with subtle bass and mid-range adjustments.

Patching the channels in series allows for radical sound shaping and band-pass responses. Each channel provides up to +/- 8db of low and high-frequency gain control, summing into a low noise output stage. Hot input signals over 15vpp are saturated by active Zener diode clipping.

Features

Precise voltage control of EQ tilt and shelf
Seamless switching between EQ modes
High-quality components used throughout

Specifications

Intellijel 1U format
Width: 18HP
Depth: 32mm
Power requirements: ~60mA +12V/~58mA -12V
Control voltage range: 0-8V
Impedance Input: 100K / Output 1K

Notes: Lush analogue EQ switchable between tilt and Baxandall high-shelf configurations.

Perform a variety of mixing and sound design duties ranging from subtle brightness and clarity adjustments to low-end rumble removal, boosted low-pass filtering and sweep EQ.

In the default tilt mode, turning the control knob clockwise simultaneously boosts treble and cuts bass. Turning anti-clockwise boosts bass and cuts treble. These boosts and cuts are pivoted around the mid-range. With the control knob at 12 o'clock the frequency response is neutral.

With Baxandall high-shelf mode enabled, turning the control knob clockwise past 12 o'clock introduces and gentle high-shelf EQ weighted around the upper mid-range. Turning the control knob anti-clockwise results in a wide high-shelf cut with subtle bass and mid-range adjustments.

Patching the channels in series allows for radical sound shaping and band-pass responses. Each channel provides up to +/- 8db of low and high-frequency gain control, summing into a low noise output stage. Hot input signals over 15vpp are saturated by active Zener diode clipping.

Features

Precise voltage control of EQ tilt and shelf
Seamless switching between EQ modes
High-quality components used throughout

Specifications

Intellijel 1U format
Width 18HP
Depth 32mm
Power requirements ~60mA +12V/~58mA -12V
Control voltage range 0-8V
Impedance Input 100K / Output 1K

Notes: Tilt is the first in Laine's series of core modules, which will take cues from the main product line and strip back the features so both the module width and cost can be shrunk dramatically.

Comprising an 'Ambler' style tilt EQ network similar to the 'Stilts' topology, Tilt allows simultaneous cut and boost of low and high frequencies using a single control.

Tilt control circuits are known for the transparency of their cut and boost curves, coupled with the inherent emphasis gained from cutting one end of the frequency spectrum whilst boosting at the opposite end.

It sounds pretty good on all audio source material but is especially suited to tracking drums, guitar and lead, or manipulating effects sends and returns.

With the control knob at 12o'clock the sound passed is neutral. Turning the control knob clockwise will boost high and cut low frequencies pivoting from a fixed mid-range point. Turning the control anti-clockwise below 12 o clock will in turn boost low frequencies and cut the highs.

In addition to the EQ there is a soft clipping network which will begin to saturate signals over 15 volts peak to peak.

Tilt uses the same high quality OPA op amps, Alpha pots and ENIG PCBs as found in our main product line.

Features

Compact EQ tilt control in 1U
Soft clipping network
High-quality components used throughout

Specifications

Intellijel 1U format
Width 8HP
Depth 28mm
Power requirements ~10mA +12V/~10mA -12V
Impedance Input 100k / Output 1k

Notes: Winnows, a dual VC resonant filter with damping.

Winnows brings radical resonant filtering to the 1U row. Make your basslines growl like it's 1999. Create clean resonant tones and layers, tuned percussion, steep filtered peaks, vowel filters and more. Each filter channel comprises two state variable filter cores, the first producing a 2-Pole band-pass response, with resonance and self-oscillation amounts set by a 3-Pole feedback network. Signals are then routed through a 1-Pole low-pass damping stage to remove harshness if required. This can be routed to the channel output, or switched and routed through a second series of resonant SVF and 1-Pole LPF damping stages. This circuitry is identical per channel.

Features and uses

Steep and spiked or wide and smooth, resonant bandpass filters
Zone in on and reinforce a sound's dominant frequency, create overtones using both channels
Create sharp resonant peaks, dull or remove any harshness with VC damping
Use the resonator as a sound source by shaping and triggering tuned percussion tones or kick drums
Per channel: 2 x VCA based SVF, 2 x 1-pole damping LPF, 1 x 3-Pole resonance core
Identical circuitry per channel, CV and audio jacks are normalled between channels
Combine both channels in series for vowel filter responses and creative filtering

Specifications

Intellijel 1U format
Width 24 HP
Depth 34mm
Power requirements ~90mA +12V/~80mA -12V
Control voltage range 0-8V
Impedance Input 100K / Output 1K

Notes: The Next Generation of Intelligent Effects Interfaces

Following the success of The Prime P1 - MOOER have refined the concept of a combined ultra-portable digital effects device and audio interface. The Prime P2 features an enhanced user experience courtesy of a 1.3" touch screen as well as a fully revamped effects and rhythm suite.

Users can access 52 amp models + 10 GNR downloadable file slots, 25 Cab Sims +10 GIR/3rd IR downloadable file slots*** and 57 classic and experimental effect models making the need for bulky pedals and multiple power supplies a thing of the past. From touch sensitive vintage amp models to huge stereo reverbs, modulations and delays based on powerful digital algorithms, the Prime P2 can more than keep up with the demands of the modern guitarist and each chain is fully customizable - that's right, you can put your effects in any order you want for maximum versatility.

The Prime P2 is the ideal tool for streaming/social media use and is designed to make immediate, high-quality sound creation as effortless as possible with seamless connectivity via Bluetooth for playback and the USB-C port for on-the-go recordings* as well as a stereo output jack and TRRS headphone input which supports headphone integrated microphone use. In addition, the integrated rechargeable battery gives up to five hours of power - making the Prime P2 a great choice for the musician on the move.

Users can download the MOOER Prime App* for increased functionality via mobile device. This allows deep-dive editing of preset patches and effects chain parameters as well as storage and recall of up to 80 presets. You can also download and share presets on the MOOER Tone Cloud.

While a mobile device can be used to control the tuner, drum machine, metronome and Looper - MOOER recommend an F-Series wireless footswitch (sold separately) for hands free operation. This transforms the Prime P2 into a very powerful live performance tool. MIDI connectivity is also available for Preset switching, Looper and Drum Machine functions using CC commands from an external MIDI controller.

Features:
Eliminates the need to carry a large number of different pedals and their associated power supplies
Easy configuration of an effects chain without complicated user interfaces
1.3" touch screen allows quick preset changes and access to the tuner directly on the device
Based on MOOER's unique MNRS technology, allowing for high-quality digital amp models and effects in a small format
52 amp models created with MNRS technology + 10 GNR slots to store simulation files downloaded from the cloud
25 cab sim models + 10 GIR slots to store simulation files downloaded from the cloud or third-party IR files
57 classic and experimental effect models
Up to 80 presets in 20 banks
Drum machine with 56 groove varieties, can be synchronized with the Looper
4 metronome styles
Looper with a total capacity of 80 minutes (storage for 10 loops with 8 minutes each)
Supports loading of 3rd party IR file
Supports Tone Cloud sound sharing
Supports stereo output for stereo effects
Stereo headphone output with support for headphones with integrated microphones.
Bluetooth audio playback in stereo for practice or jamming
USB-C charging port also supports audio playback over USB and USB-OTG for live streaming and easy recording
Can be controlled using MOOER F-series wireless footswitches
Can be controlled from an external MIDI controller
Integrated rechargeable battery with up to 5 hours of battery life
Free mobile app for easy editing of sounds as well as saving, organizing and sharing presets**
MOOER Studio PC management software for backup and updates, 3rd IR loading.
* An adaptor may be necessary depending on your device
** The MOOER Prime App is available from Google Play Store, Apple App Store or the official MOOER Download-Support website.
***MNRS is MOOERS's proprietary sampling technology which can be used to sample preamps, combos, pedals and speaker cabinets - MOOER MNRS Sample files come in two categories - GNR files (Amps, preamps, pedals and effects) and GIR files (Cabinet models) for a huge array of sounds.

Specifications
Input: 6.35 mm (1/4") TS, 2 MO
Output: 6.35 mm (1/4") TRS, 100 O
Headphone: 3.5 mm (1/8"), 32 O
Screen: 1.28" Touch Screen
USB: Type C for charging or OTG recording
Bluetooth version: 5.0
Bluetooth: Bluetooth audio playback and App control
Wireless control: 2.4G
Wireless footswitch: supported
Battery capacity: 3000 mAh
Battery life: 5 hours*
MIDI Port: 3.5 mm (1/8")
Charging requirement: 5VDC / 2 A (10 W)
Charging time: 2.5 hours for full charge*
Dimensions: 120 x 64 x 21 mm (LxWxH)
Weight: 152 g
Accessories: Quick-Start manual, USB-C to USB-A cable, 3.5 mm jack to 5-PIN MIDI-connector

*Charging time and battery life are based on lab test data.
Disclaimer: Parameter updates will not be notified separately.

Notes: The Next Generation of Intelligent Effects Interfaces

Following the success of The Prime P1 - MOOER have refined the concept of a combined ultra portable digital effects device and audio interface. The Prime P2 features an enhanced user experience courtesy of a 1.3" touch screen as well as a fully revamped effects and rhythm suite.

Users can access 52 amp models + 10 GNR downloadable file slots, 25 Cab Sims +10 GIR/3rd IR downloadable file slots*** and 57 classic and experimental effect models making the need for bulky pedals and multiple power supplies a thing of the past. From touch sensitive vintage amp models to huge stereo reverbs, modulations and delays based on powerful digital algorithms, the Prime P2 can more than keep up with the demands of the modern guitarist and each chain is fully customizable - that's right, you can put your effects in any order you want for maximum versatility.

The Prime P2 is the ideal tool for streaming/social media use and is designed to make immediate, high-quality sound creation as effortless as possible with seamless connectivity via Bluetooth for playback and the USB-C port for on-the-go recordings* as well as a stereo output jack and TRRS headphone input which supports headphone integrated microphone use. In addition, the integrated rechargeable battery gives up to five hours of power - making the Prime P2 a great choice for the musician on the move.

Users can download the MOOER Prime App* for increased functionality via mobile device. This allows deep-dive editing of preset patches and effects chain parameters as well as storage and recall of up to 80 presets. You can also download and share presets on the MOOER Tone Cloud.

While a mobile device can be used to control the tuner, drum machine, metronome and Looper - MOOER recommend an F-Series wireless footswitch (sold separately) for hands-free operation. This transforms the Prime P2 into a very powerful live performance tool. MIDI connectivity is also available for Preset switching, Looper and Drum Machine functions using CC commands from an external MIDI controller.

Features:

Eliminates the need to carry a large number of different pedals and their associated power supplies
Easy configuration of an effects chain without complicated user interfaces 1.3" touch screen allows quick preset changes and access to the tuner directly on the device
Based on MOOER's unique MNRS technology, allowing for high-quality digital amp models and effects in a small format
52 amp models created with MNRS technology + 10 GNR slots to store simulation files downloaded from the cloud
25 cab sim models + 10 GIR slots to store simulation files downloaded from the cloud or third-party IR files
57 classic and experimental effect models
Up to 80 presets in 20 banks
Drum machine with 56 groove varieties, can be synchronized with the Looper
4 metronome styles
Looper with a total capacity of 80 minutes (storage for 10 loops with 8 minutes each)
Supports loading of 3rd party IR file
Supports Tone Cloud sound sharing
Supports stereo output for stereo effects
Stereo headphone output with support for headphones with integrated microphones.
Bluetooth audio playback in stereo for practice or jamming
USB-C charging port also supports audio playback over USB and USB-OTG for live streaming and easy recording
Can be controlled using MOOER F-series wireless footswitches
Can be controlled from an external MIDI controller
Integrated rechargeable battery with up to 5 hours of battery life
Free mobile app for easy editing of sounds as well as saving, organizing and sharing presets**
MOOER Studio PC management software for backup and updates, 3rd IR loading.

* An adaptor may be necessary depending on your device
** The MOOER Prime App is available from Google Play Store, Apple App Store or the official MOOER Download-Support website.
***MNRS is MOOERS's proprietary sampling technology which can be used to sample preamps, combos, pedals and speaker cabinets - MOOER MNRS Sample files come in two categories - GNR files (Amps, preamps, pedals and effects) and GIR files (Cabinet models) for a huge array of sounds.

Notes: The Morphor Envelope - Dual ADSR is a slim (6 HP) dual envelope generator. Each channel features standard ADSR (Attack, Decay, Sustain, Release) analogue circuitry, providing the classic, rich envelope shaping tools essential for any modular enthusiast. It features separate control knobs for the attack, decay, sustain and release parameters, two independent channels for versatile envelope shaping and each channel comes equipped with gate, re-trigger, output, and an inverted output.

On the back of the module you can find tiny switches for each channel to change the overall length of the complete envelope:
Short: 5 ms - 30 s
Med: 25 ms - 60 s
Long: 60 ms - 200 s (=3.3 min)

Features

100% analogue
Dual channel
Attack length control
Decay length control
Sustain level control
Release length control
Inverted output
Re-trigger

Specifications

Panel width: 6 HP
Panel height: 3 U
Module depth: 40 mm
Current draw: 12 V : 32 mA | -12 V : 32 mA | +5 V : 0 mA
Dimensions: 128.5 x 30.3 x 40 mm
Weight: 111 g
Power Socket : 16-pin

Notes: The Morphor LFO - Dual is a slim (6 HP) dual LFO. Each channel features analogue triangle, square, sine, saw and inverted saw outputs and a cycle reset input.

Frequency ranges:

Low: 0.005 - 1.5 Hz
Med: 1.5 - 425 Hz
High: 15 - 4250 Hz

Features

100% analogue
Dual channel
Triangle wave output
Square wave output
Sine wave output
Saw output
Inverted saw output
Cycle reset input
Low/Med/High frequency selector

Specifications

Panel width: 6 HP
Panel height: 3 U
Module depth: 25 mm
Current draw: 12 V : 22 mA | -12 V : 22 mA | +5 V : 0 mA
Dimensions: 128.5 x 30.3 x 25 mm
Weight: 71 g
Power Socket : 10-pin

Notes: CV Random is a random CV generator with 4 types of randomness and a triggerable sample-and-hold function.

Sliders allow you to set the internal clock tempo (RATE), shape the probability of triggering (PROB), blend old with new values (RND) and set the shape of all four random outputs (SHAPE).

4 different sliders

RATE

Sets the tempo of the internal clock. The CV input below the slider adjusts the clock rate, with 1V/oct calibration when the CV attenuverter is 100%. Upon each clock trigger, the RATE slider light blinks, and there is a chance for the internal random source to generate a new value.

PROB

This probability is set by the PROB slider, and if a new value was generated, the PROB slider light blinks and a pulse is emitted from the TRIG output.

RND

When the internal random source generates a new value, it mixes the previous value with a random value, with an amount specified by the RND slider.

SHAPE

The SHAPE slider sets the shape of all four random outputs. At its lowest position (0%), all outputs immediately jump to the new random value (the target value) when the clock is triggered.

At non-zero positions, the outputs interpolate between the previous and the target value, using a different behaviour for each output.

Internal random clock source

Whenever the clock activates, the RATE slider's light flashes. At the same time, there's a chance that the internal random source will create a new value, depending on the PROB slider's setting.

If it does create a new value, the PROB slider's light flashes too, and a pulse comes out of the TRIG output.

External IN & TRIG inputs

If the TRIG input is patched, the RATE slider is ignored, and the internal clock is only triggered when an external trigger is received. The PROB slider is used to filter this trigger by applying some probability.

Self-modulation

Thanks to a switch in the back of the module, you can normalize the LIN output to the 4 CV inputs and adjust the amount of modulation for each parameter with the attenuverters.

This adds another layer of randomness to your results, enabling more dynamic and unpredictable outcomes.

SHAPE Outputs

The STEP output jumps to the new value in one step at 0% SHAPE, and divides the transition into 16 steps at 100% SHAPE.

The LIN output immediately reaches the new value at 0% SHAPE, and takes the whole clock cycle to do so at 100% SHAPE, staying constant in between.

The EXP output shifts exponentially, becoming linear at 100% SHAPE, with its pace adjusted by the SHAPE slider.

The SMTH output transitions smoothly, with the speed controlled by the SHAPE setting, holding at the target until the cycle ends.

Specifications

Dimensions 10HP - 50×128,5mm
Current 63 mA +12V / 11 mA -12V / 0 mA +5V
Input & Output Signals +/-10V
Impedance Input 10k - Output 10k
Materials PCB and Panel - FR4 1,6mm
Depth 40mm including connectors (Skiff friendly)

Notes: Really nice take on an arpeggiator module here. Four-channel design features editable arpeggio patterns, CV control and transposition. Real-time performance meets customisable melody generation.

Supplier's Notes:
Four-channel arpeggiator with customizable patterns and CV control

Opp Ned is a four-channel arpeggiator designed for creating patterns that can be modified with CV. Opp Ned ships with 12 of Noise Engineering's favourite arps, including tetrads, major, pentatonic major, minor third, and pentatonic minor, but you can edit and save custom arpeggios to twelve memory slots. Recall your custom arpeggios manually or with CV using the Ptn input. If you ever want to restore the factory arps, just head to the Noise Engineering Customer Portal.

The transpose input makes it easy to combine Opp Ned with external sequencers, too!

Arps have never been easier than with Opp Ned.

Features

Size and Power
8HP Eurorack
+12v: 60mA
-12v: 10mA

Opp from Norwegian Opp for "Up"
Ned from Norwegian Ned "down"
"Ups and downs"

What's in the box

Module
Power cable

*** Noise Engineering no longer include screws with newly packaged modules. Bulk screws are available for purchase. ***

Notes: Four-channel arpeggiator with customizable patterns and CV control

Opp Ned is a four-channel arpeggiator designed for creating patterns that can be modified with CV. Opp Ned ships with 12 of Nosie Engineering's favourite arps, including tetrads, major, pentatonic major, minor third, and pentatonic minor, but you can edit and save custom arpeggios to twelve memory slots. Recall your custom arpeggios manually or with CV using the Ptn input. If you ever want to restore the factory arps, just head to the Noise Engineering Customer Portal.

The transpose input makes it easy to combine Opp Ned with external sequencers, too!

Arps have never been easier than with Opp Ned.

Features

Size and Power
8HP Eurorack
+12v: 60mA
-12v: 10mA

Opp from Norwegian Opp for "Up"
Ned from Norwegian Ned "down"
"Ups and downs"

What's in the box

Module
Power cable

*** Noise Engineering no longer include screws with newly packaged modules. Bulk screws are available for purchase. ***