DJ-Equipment charts

Notes: Replacement JNP100 stylus with spherical tip and aluminium alloy cantilever.

Fits MP100 cartridge.

Notes: This brush contains more than one million very fine carbon fibre bristles. The cross section of these bristles is so small that they can easily get into all the nooks and crannies of the record groove. Because the carbon fiber conducts electricity it takes away all the static to earth via the metal handle and the person holding the brush. Then the dust lies loose in the groove so the next set of bristles can easily pick them up and remove them from the record groove.

Notes: Tonar plastipap antistatic record inner sleeves (25 pieces) are made of super antistatic plastic paper reinforcement inside the plastic. This combination gives you both a dust free anti-static protection for your valuable records as well as additional strenght to avoid folding and creasing of the sleeves when sliding the sleeve in and out of the record album. This model 5311 plastipap is suitable for LP records only (12 inch-30 cm). Tonar plastipap inner sleeves are also available for 45, and 78 RPM records.

Tonar supplies record inner sleeves for 33, 45 and 78 RPM records as well as outer sleeves to protect your valuable album sleeves.

Notes: A 45 rpm adapter (also 45 rpm record insert, or 45 rpm spindle adapter) is a small plastic or metal insert that goes in the middle of a 45-rpm record so it will play on a turntable. The adapter could be a small solid circle that fits onto the bottom of the spindle (meaning only one 45 could be played at a time) or a larger adapter that fits over the entire spindle, permitting a stack of 45s to be played.

Notes: 10x 12" 400 gauge polythene record sleeves.

Notes: Typically good value from Omnitronic with this entry-level turntable. Belt drive makes it a little trickier to mix on than a more expensive direct-drive model but good solid sound quality for general listening.

Supplier notes:
Includes pick-up system
- Adjustable +/- 10% speed control
- Large start/stop button
- Strobe lamp for exact speed adjustment
- Includes removable dustcover
- Adjustable anti-skating
- Shock-absorbing feet

Notes: Center-piece for singles - aluminium silver.

Notes: - Makes scratching easier
- Protects your turntable-motor and the records
- Antistatic
- Diameter approx. 290 mm

Notes: Drain the static charge from your records and lift any residual dust and grime with the anti-static vinyl brush.
The conductivity of the brush's carbon fibre bristles eliminates static charges while gently and efficiently removing the dust, grit and particles that bung up your vinyl's grooves and degrade your record's sound.
The conductive carbon fibres reach deep into the grooves of your vinyl to remove even the smallest particles, leaving your records clean while prolonging the life of vinyl and stylus.

- Hand-made carbon hair brush for removing dust from vinyl records
- The brush makes the record antistatic so it does not attract dust
- For those who care for their collection of vintage or brand new vinyl records
- Can also be used for Schellack records

Notes: Designed and engineered in the UK specifically for the Reloop RP7000 & 8000 turntables. Custom moulded from super durable polycarbonate and finished in a slick smoked/clear hue. Simple push fit design shields tone-arm and other delicate components from accidental damage, whilst leaving cables in place.

Notes: We're familiar with IsoAcoustics' highly effective line of monitor isolation stands that seem to bring out the best from any speaker. NAMM 2017 will see IsoAcoustics release the new Iso-Puck - the same concept as the bigger stands, yet in a low-profile, flexible, scalable version. The little puck-like discs are placed under your speaker to isolate them from the surface they're sitting on.

An Iso-Puck is pretty small - just 3cm tall and 6cm in diameter. Its round shape makes positioning a bit easier than with stands, especially on varied surfaces like the narrow space on top of a console meter bridge. The multipart isolation construction of the Iso-Puck lets it move to isolate and manage the energy in line with the same isolation concepts employed in other IsoAcoustics products. The Pucks feature a flange suction cup on the top to hold tight the speaker surface, as well as a bottom suction cup flange for the supporting surface. Energy is transferred to the core of the multipart isolator in between which resists lateral movement and offers better isolation.

Notes: The sound performance of a vinyl playback system can be significantly improved when all unwanted resonances between the record and the platter can be reduced during playback. Enter record clamps and pucks; simple devices which are designed solely to ensure the record and platter surfaces are held together tightly.

Standard record pucks, that use only weight to achieve this aim, can have 2 disadvantages:

- The weight can induce higher levels of rumble, when used with lower cost turntables which have smaller main bearings
- Instead of tightening the records surface to the platter, heavy weight record pucks can cause the opposite to happen and potentially warp the vinyl record into a slight 'bowl' shape

Pro-Ject's Clamp-IT is one of the most competent solutions available. It is a stylish accessory with a clamp mechanism around the centre spindle, that will not add weight but will press the record against the platter. The Clamp-IT also allows you to fine-adjust the pressure depending on the condition of your warped records.

Fitting of Pro-Ject's Clamp-IT is easily done, and once it's in place it won't only please your ears; because its beautifully machined diamond-cut edges will also stand out on any turntable!

Notes: A popular replacement stylus. Individually packed in a plastic case. Made in Japan.

Notes: Developed in the UK by DJ's, Record Collectors & Vinyl Enthusiasts.

Near Mint has been specially blended to make sure your vinyl is cleaned to the highest standard. Using a greater percentage of integral ingredients and purified chemicals, Near Mint can offer the best results in cleanliness, ensuring no residue remains on your record.

Near Mint is the most effective, chemically balanced & hard hitting record cleaning solution on the market to date boasting a double strength attitude.

Notes: This 4-in-1 vinyl cleaning solution includes a velvet record brush, XL cleaning liquid, stylus brush and travel pouch.

This handy kit will keep your collection sounding great. Clean dust, dirt and fingerprints off your records to improve sound quality instantly!

All-in-one solution: Clean dust, dirt and fingerprints using the anti static velvet brush in combination with the cleaning spray. The included stylus brush will remove any particles off your record player's needle.

No carbon, no scratching: Unlike other record brushes made from carbon fiber, the soft velvet brush will not leave a scratch on your precious vinyl. PS: You can even use it to clean your phone screen!

Extra large cleaning fluid: The included 50ml bottle should last you quite a while.

Notes: Numark's take on the classic scratch mixer formula ticks all the boxes: two channels each with three-band EQ, plus perfectly spaced channel faders and crossfader for cutting and scratching. Simple but effective.

Supplier's Notes:
Pure professional power.

M2 is a two-channel DJ scratch mixer with all the essentials to hit the stage in Numark style.

Switchable phono/line inputs for turntables, CD players, and other line sources make M2 a superb choice for any DJ setting from weddings to clubs, parties to practice setups. A mic input with dedicated EQ and gain, and a headphone output with crossfader-style cueing complete the plentifully featured package.

Three-band EQ on each channel plus crossfader-reverse and slope controls give you all the tools you need to drive your audience from behind the wheels of steel. M2 is the perfect mixer for any scratch DJ.

Packaged Dimensions: 14.6" x 13.4" x 6.7"

Packaged Weight: 8.8 lbs.

Product Dimensions: 11.4" x 9.5" x 3.6"

Notes: Rane's unique vinyl-style digital turntable controller offers old-school feel with modern control over your DJ software. MKII model improves on the original with features including new controls and display.

Supplier's Notes:
Solid steel, precision performance

The Rane Twelve MKII feels instantly familiar to any DJ who has played vinyl, adding hot-cue and track search capability at the touch of a finger. The MKII now adds USB & DVS control for track browse & selecting, and instant doubles.

The Twelve MKII provides USB MIDI and DVS control for Traktor, Virtual DJ and Serato DJs. Select your desired platform and connect for the ultimate vinyl legacy experience in a digital world.

With the strength and durability of a solid-steel casing and aluminium platter, the gig and battle-ready Twelve MKII represents the ultimate in advanced music control for high performance and creative DJs.

Traditional 12" turntable platter with no-latency precision for seamless DJ performances.

Delving deeper into the foundation DJ experience, the plunger style Start/Stop button has that classic feel for turntable loving DJs.

The MKII includes a stereo RCA audio output to deliver DVS tones for multiple DJ software platforms, selected via the OLED screen on the top.

Tech Specs

Motor
Drive: Quartz direct-drive
Torque: High: 5.0 kgf/cm (starting/instant); 3.4 kgf/cm (stable) / Low: 3.2 kgf/cm (starting/instant); 1.4 kgf/cm (stable)
Starting Time: < 0.4 seconds
Braking System: Electronic

Platter
Material: Aluminum die-cast
Diameter: 13.1" / 332 mm
Weight: 4.9 lbs. / 2.2 g
Speeds: 33 1/3, 45 RPM
Pitch Range: +8%, +16%, +50%
Connectors: 1x USB Type-B port, 1x Stereo RCA output, 1x IEC power cable input

Power
Voltage: 100-240 VAC, 50/60 Hz
Consumption: 60 W

Dimensions (wxdxh): 14.5" x 16.2" x 5.3" (368 x 413 x 90 mm)
Weight: 20.5 lbs. (9.3 kg)

Notes: All new exciting styles and designs created for 2021 in collaboration with Magma, Technics have released 20 new slipmats to suit your style and aesthetic.

Perfect for all types of turntables and vinyl players, the soft felt design works to eliminate static charge expelling from your vinyl records. Protecting your turnable as well as your record, the slipmat ensures both your turntable and record stay in working order and helps to reduce scratches.

Suited to all styles, these slipmats from Technics are functional as well as visually pleasing; working well with scratch DJs, as well as audiophiles these slipmats have you covered and looking good.

Notes: Pair of high quality felt slipmats in black with gold Technics logo design

Notes: Wireless music creation with ultra-low latency and uncompressed audio with W+ Link technology.

Uncompressed and robust 16ms latency connection for high quality wireless audio designed for enhanced freedom and creativity.

Signature AIAIAI bio-diaphragm speaker tuned for clarity and detail.

Critically acclaimed sound stage specifically designed for music creation with a clear and highly detailed sound representation.

Enhanced comfort with Alcantarar over-ear memory foam cushions.

Soft over-ear memory foam cushions covered with resilient, CO2 neutral, and highly comfortable Alcantarar, ideal for longer sessions.

Modular product design.

This TMA-2 modular headphone system offers a customizable solution that adapts to your creative process. With interchangeable components such as earpads, cables, and drivers, you can upgrade or change parts of your headphones to improve sound quality, comfort, or style.

Extended versatility with added Bluetooth for +80h playback and hi-fi coiled cable.

Seamlessly switch to Bluetooth 5.0 with +80h playback for everyday listening and inspiration, and a coiled hi-fi cable included for a traditional connection.

Headphones for life.

AIAIAI offer lifetime trade-in for your headphones or modular parts. With this program, users can leverage the modular product design to get maximum value from their purchase by swapping out used or non-functional headphones or parts for future credit. This means only investing in one pair of headphones, for life.

Wireless music creation with ultra-low latency and uncompressed audio with W+ Link technology.
Signature AIAIAI bio-diaphragm speaker tuned for clarity and detail.
Enhanced comfort with Alcantarar over-ear memory foam cushions.
Modular product design - Headphones for life.
Extended versatility with added Bluetooth for +80h playback and hi-fi coiled cable.

Technical specifications

W+ Link Headband

Audio quality: Lossless
Latency: 16 ms
Operating range: 12 m
Playback time: 16 hrs
Bluetooth version: 5.0
Bluetooth range: 10 m
Charging time: 2 hrs
Battery: 970 mAh
Omnidirectional mic: 100 Hz - 10 kHz
Bluetooth codecs: AAC, SBC

W+ Link Transmitter

Audio quality: Lossless
Latency: 16 ms
Operating range: 12 m
Playback time: 30 hrs
Charging time: 3 hrs
Battery 2700 mAh

Notes: Black version of Audio-Technica's entry-level DJ turntable, updated to feature an improved direct-drive motor. Built-in phono preamp and USB audio interface make it easy to connect to any mixer, powered speakers or computer.

Supplier's Notes:
AT-LP120XUSB Direct-Drive Fully Manual Turntable

This update of the AT-LP120-USB turntable features a new DC servo direct-drive motor, along with adjustable dynamic anti-skate control and selectable phono preamplifier. The fully manual turntable plays 33-1/3, 45, and 78 RPM records and is equipped with a USB output that allows direct connection to your computer. Just download the free Mac- and PC-compatible Audacity recording software (or software of your choice) and start converting your records to digital audio files.

But in addition to the USB output, the turntable also comes with a detachable dual RCA output cable and is equipped with a built-in selectable phono preamp so you can connect directly to your home stereo, whether it has a dedicated phono input or not. The turntable features an S-shaped tonearm with adjustable tracking force and an AT-HS6 universal 1/2"-mount headshell with an AT-VM95E Dual Magnet phono cartridge.

Audio-Technica has been a leader in phono cartridge design for more than 50 years, and that expertise shows in the versatile, high-performance AT-VM95E cartridge, which comes with a 0.3 x 0.7 mil elliptical stylus, but is also compatible with any VM95 Series replacement stylus, offering a wide choice of options for every budget and application. Additional features include a die-cast aluminium platter with felt mat; a start/stop button; selectable high-accuracy quartz-controlled pitch lock and pitch change slider control with +/-8% or +/-16% adjustment ranges; a stroboscopic platter with speed indicator; a removable plug-type stylus target light; external power supply; and a removable hinged dust cover.

Analogue or USB Connection

Next-Generation Analogue/USB Turntable

An update of the critically acclaimed AT-LP120-USB, this turntable features a new DC servo direct-drive motor, along with adjustable dynamic anti-skate control and selectable phono preamplifier.

Plays 33-1/3 RPM, 45 RPM and 78 RPM Records

USB and Analogue Output

Built-in Switchable Phono Pre-Amplifier

AT-VM95E Dual Magnet Phono Cartridge

Taking Your Vinyl to the Next Level

High-Fidelity Home Audio

Whether using with your home stereo system or your computer, the AT-LP120XUSB's professional controls give you the power to shape your high-fidelity listening experience.

Cartridge Assembly Line Circa 1962

Half a Century of Stunning Analogue Sound

Audio Technica was started in Tokyo in 1962, designing and manufacturing high-performance phono cartridges. That half-century's worth of analogue expertise goes into every turntable produced, ensuring you get the best listening experience from your vinyl.

Specifications

Turntable

Type: 3-speed, fully manual operation
Motor: DC servo motor
Drive Method: Direct drive
Speeds: 33-1/3 RPM, 45 RPM, 78 RPM
Turntable Platter: Die-cast aluminum
Starting Torque: >1.0 kgf.cm
Braking System: Electronic brake
Wow and Flutter: <0.2% (WTD) @ 3 kHz (JIS)
Signal-to-Noise Ratio: >50 dB
Output Level: Pre-amp "PHONO": 4 mV nominal at 1 kHz, 5 cm/sec
Pre-amp "LINE": 240 mV nominal at 1 kHz, 5 cm/sec
Phono Pre-Amp Gain: 36 dB nominal, RIAA equalized
USB Function: A/D, D/A - 16-bit/44.1 kHz or 48 kHz USB selectable;
Computer interface: USB 1.1 Compliant Windows 7 or above, or MAC OS X or above
Power Supply Requirements: 100 to 240 V, 50/60 Hz, 1.5A Max.
Dimensions: 452.0 mm (17.80") W x 352.0 mm (13.86") D x 141.6 mm (5.57") H
Weight: 8 kg (17.6 lbs.), without dust cover
Accessories Included: AT-VM95E phono cartridge; AT-HS6 headshell; 1.9 m (6.2') USB cable; dual RCA (male) to dual RCA (male) cable with ground wire; counterweight; felt mat; dust cover; 45 RPM adapter; plug-type stylus target light

Notes: If you're just getting into vinyl, or finding your way back, the GrooveWasher INTRO Kit is a great way to enhance your overall experience. This Kit cleans your records using High Tech G2 Record Cleaning Fluid with our highly absorbent and washable microfiber fabric covered pad. The Label Protector Disc keeps the record label dry during cleaning.

If the price tag for other GrooveWasher Kit's is a hurdle, give this low cost INTRO Kit a try!

The INTRO Kit contains:

Microfiber fabric covered cleaning pad. Generous size: 5" x 3.5" x 1.5". Highly absorbent and grime removing fabric. Easy to use to clean records. Easy to wash when it gets dirty.

G2 High Tech Record Cleaning Fluid in 2 oz Mist Spray. More than 250 mist sprays to clean a lot of records!

Record label protector mask. Apply to the record label to keep it dry while mist spraying the G2 Fluid on the record.

Notes: Highly absorbent split-fiber microfiber fabric. Black terry close style. Works well on heavily soiled records or for fine grooming just before play.

This pad has a 3/16" thick, laser cut acrylic base. The pad base has low profile velcro for firm attachment to the walnut handle. Easy removal for pad washing or replacement. Hand crafted by our pad making artisans in North Kansas City, Missouri, USA.

Notes: Audio Optimized USB-C to USB-B Cables

56kO pull-up resistor to protect your devices
Dual slimline ferrites prevent signal dropouts
High quality connectors ensure long cable life
Works with all USB-B devices

Ideal for home and professional use where impeccable audio is a must, Chroma Cables complement the modern DJ and music production technology with a streamlined styling that keeps your setup looking fresh and sleek. All cables are not created equal, and ours are engineered from scratch for digital performers, by digital performers.

Noise-Filtering Features

Each cable has two ferrite core chokes, one at each end of the cable. Paired with fully-braided shielding, Chroma Cables do a great job of eliminating interference along the signal path - making these the best USB cables for DJs.

No More Adapters

Forget about tiny adapters that can easily get lost in a dark booth. These high quality USB-C cables ensure that all your audio and MIDI devices have a reliable connection with no compromises.

Always Strapped

Even after placing your cables neatly in your bag, it's easy to wind up with a tangled clump of cables. The built-in velcro cable strap helps prevent this, keeping your gig bag nice and tidy. You'll wonder how you managed without this.

Compatibility Notes:

Works with all* USB devices with a USB type B connector but it's worth checking for obstructions if you plan on ordering an angled cable.

*Please note that the right angle cable won't work with a Kontrol D2, S2, S4, S5, S8, or Z1 or Traktor Audio 10 while using the power supply.

Size + Weight:
Length: 59.05" / 150cm
Weight: 0.18lb / 0.08kg"

Notes: Mains Power Leads UK - IEC 10A

UK 3 pin plug to IEC C13 female plug 3 cores mains power lead, suitable for connecting power to general electronic equipment up to 2300W (10A).

Max. current: 10A
Max. power: 2300W

Notes: Two slipmats in a stylish Daft Punk design.

Ideal for all types of DJ techniques, to protect the records and the turntable drive, reduce static charging or improve the look.

Notes: The MP 200 is a unique cartridge. It manages to provide an amazingly rich and warm mid range for jazz and vocals while still providing the detail and dynamics across the spectrum. It's not just another "warm sounding" cartridge.

Specifications

Type: Moving magnet (Permalloy)
Cantilever: High-strength Boron
Stylus type: Superfine elliptical diamond
Weight: 6.5 g
Output voltage @ 1kHz,5cm/sec: 4mV
Frequency response: 20Hz-23kHz
Channel balance @ 1kHz: > 1.5dB
Channel separation @ 1kHz: > 25dB
Recommended loading: 47k ohms
Dynamic compliance: 7.2 x 10-6 cm/dyne
Static compliance: 20 x 10-6 cm/dyne
Tracking force range: 1.5 - 2.0 g
Break-in period: 30 hours
Stylus replacement: Nagaoka JN-P200

Notes: Nagaoka JNP-200 Replacement Stylus is the original replacement stylus for the MP-200 MM cartridge featuring an elliptical block diamond tip and boron cantilever.

Replace a worn out or defective stylus to prevent damage to your records, and enjoy the best from your records again with more musical information being extracted from the vinyl grooves, allowing you to enjoy the best sound quality.

Tech Specs

Cantilever: Boron

Stylus: 0.4 x 0.7 Mil naked elliptical block diamond stylus tip

Notes: The G2 Record Cleaning Fluid Kit includes:

- One 2 ounce bottle of G2 Fluid, with mist spray top.
- One 4 ounce bottle of G2 Fluid with spout top. Use to refill the 2 oz mist spray bottle. 900+ mist sprays in this kit.
- Label protector mask. Use to keep your record label dry when using the mist spray.
- Record Cleaning Instruction Booklet.

GrooveWasher G2 Fluid is the result of years of research and testing. The formula was guided by the D series fluids of the 1970s. G2 is perfectly safe for vinyl records. The ingredients are balanced for effective cleaning without rinsing. Evaporates quickly after cleaning per instructions. Anti-static action on contact. Honest cleaning to release the honest sound of the recording.

Designed for use with the GrooveWasher cleaning pads. But you can use G2 Fluid with your preferred absorbent brush or fabric. NOTE: Carbon fiber brushes are non-absorbent and not designed for wet cleaning. Use of G2 Fluid with a carbon fiber brush is not recommended.

RCM owners tell us they prefer G2 Fluid for the cleaning cycle.

G2 does not fix scratches or scuffs. Once the signal in the microgroove is lost, nothing will recover it.

The two ounce mist spray bottle has more than 300 fine mist sprays. With the 4 ounce refill bottle this kit provides 900+ fine mist sprays. Enough to clean both sides of more than 100 records! (YMMV)

Some vinyl cleaning fluids on the market are plain distilled water with limited cleaning action. Others have a high level of alcohol which can harm vinyl records. Some leave a layer in the microgroove that reduces sound fidelity.

High Tech G2 Fluid Contains:

- Surfactants: State of the art detergents dissolve and suspend fingerprints and other oily grime.
- Super wetting agent: A specialty chemical that reduces the G2 Fluid's surface tension to reach the bottom of the groove. When you spray G2 Fluid on a record you can see it spread down the grooves.
- Emulsifiers: Holds the oils, dirt, mildew and microdust particles in suspension. Then the microfiber fabric cleaning pad wipes and pulls the dirt-filled solution from the record surface.
- Purified, deionized water: Powerful carrier for the active cleaning ingredients. Eliminates static electric charges on the record's surface on contact.

"I haven't realized how "dirty" my record grooves have been. I used the Groovewasher on a 1979 copy of JJ Cale's 5 record. This is a quiet, laid back, nice, record and I heard parts of JJ Cale's voice that I have not noticed before. This out shines all the competition. I hope this flies off of the shelves as people discover it. Keep up the good work." Thomas Lee

"This is simply the best cleaning fluid available today. I highly recommend this product and this company." Dan B

G2 Record Cleaning Fluid is formulated and made by GrooveWasher in North Kansas City, MO, USA.

Notes: Protective outer record sleeves

Provides a lifetime of protection for your valuable record collection

100x 3-mil polyethylene sleeves
12.75" x 12.75"
No flap
Fits one 12" standard single or gatefold jacket

Notes: Protective outer record sleeves

Provides a lifetime of protection for your valuable record collection

50x 3-mil polyethylene sleeves
12.75" x 12.75"
No flap
Fits one 12" standard single or gatefold jacket

Notes: A popular replacement stylus. Individually packed in a plastic case. Made in Japan.

Colour: Grey
Product Dimensions (mm): 11x20x10
Net weight (kg): 0.01
Gross Weight (kg): 0.013
Packaged dimensions (HxWxL mm): 20x50x20
Transport dimensions (mm): 50x20x20
Gross Weight (Packaged) (kg) : 0.013

Notes: Aluminium-framed 50-capacity hinged 12"/LP record box with removable lid, reinforced rounded corners and EVA lining.

Notes: Aluminium-framed 100-capacity 7" record box with reinforced corners, hinged lid, EVA/egg foam lining, twin handles and supporting feet.

Notes: 200-capacity lockable 7" record box with aluminium frame, hinged lid and egg-foam/EVA lining.

Notes: Heavy-duty 100-capacity 12"/LP record box with hinged lid, aluminium frame, reinforced rounded corners and butterfly clasp.

Notes: Designed for seamless integration with Serato and the Stem-Split feature, the Four is Rane's flagship controller. Clever compatibility options let you add vinyl, CDJs and other controllers like the Rane Twelve or Denon LC6000.

Supplier's Notes:
Designed for creativity, built to last

The FOUR brilliantly combines the latest in performance-focused DJ technology with RANE's tried-and-true build and industry-leading sound quality. The result is a bulletproof, great sounding, feature-packed DJ controller that will unleash exciting new levels of creativity in your DJ sets and livestreams. With never-before-seen features like STEM-SPLIT, Performance Pad OLED displays, and a new dynamic internal FX engine, the FOUR is the world's most advanced 4-channel Stems DJ controller.

Harness the power of Serato stems

RANE and Serato have a long history of creating ground-breaking DJ products together, dating back to the RANE SL1 box in 2004. The RANE FOUR takes this partnership to the next level by melding the industrial-grade build and sound quality of RANE hardware with the powerful new Stems capabilities of Serato DJ software. The result is a next-level DJ controller with unprecedented Serato Stems control. A dedicated Stems Pad Mode, Instrumental and Acapella buttons, and RANE's exclusive STEM-SPLIT feature provide you with the ultimate Stems workflow and experience to fully elevate your creativity as a DJ.

New levels of creative FX

The newly designed internal FX suite features 22 paddle-triggered, fully customizable Main FX and 4 knob-controlled Channel FX for adding flavour and personality to individual Stems elements and tracks. This robust FX suite features traditional FX classics like Reverb and Echo and exhilarating new additions including Scale Down, Recycler, Riser, and more. The Channel FX section offers dynamic, hands-on manipulation of 4 knob-controlled FX including Filter, Filter Roll, Noise, and Flanger. The RANE FOUR also allows you to switch seamless back and forth between the built-in hardware FX and Serato's software FX, providing limitless options for any style of DJing.

Four channels of performance possibility

The 4-channel mixer section features full EQ control and intuitive FX assignment options, plus 2 external Line/Phono inputs for external turntables or decks. The FOUR is DVS-enabled and unlocks both Serato DJ Pro and Serato Pitch 'n Time when connected to laptop running the latest version of Serato. Enhanced Sampler routing options allow you to control the Sampler volume via a dedicated knob, or assign the audio to Channel 4 so that you can layer FX on top of your DJ drops, instruments, and other samples. The quick-access deck selection buttons allow for swiftly switching platter control between software decks, and the FOUR also supports external modular decks like the RANE TWELVE MKII and the Denon DJ LC6000 for a full physical 4-deck mixing experience.

Focus on your performance, not your laptop

The 8 OLED displays above the Performance Pads on each deck offer visual feedback for all pad modes, making it easier than ever to see the function of each pad without having to look at the computer. See Cue, Loop, and Sample names as well as Roll and Loop lengths, beat divisions, Pitch Play tuning, and Stem elements and FX.

The best static platters... ever

The 8.5" capacitive jog wheels were designed to be the smoothest and most accurate static jog wheels available on a DJ controller. A central colour display indicates play head position, BPM, pitch percentage, pitch range, overview waveform with Hot Cue markers, song key, time, loop size, deck selection, Beat Jump length and more.

Trusted Rane quality

The RANE FOUR is the only 4-channel DJ controller built to RANE's rigorous standards. Solid, bulletproof construction, MAG-FOUR crossfader with curve adjustment and channel assignment switches, aluminium FX toggles, and industry-leading sound quality and connections ensure that the RANE FOUR will always perform like a champ, no matter what.

Technical Specifications

Digital Audio

Converters: Cirrus Logic, 24-bit PCM, 48 kHz
Digital Signal Processing: 32-bit, Floating Point, Double precision
Dynamic Range (A-weighted, unity gain): ADC: 113 dB DAC: 113 dB
CD Input to Analog Output: 110 dB
CD Input to USB Output: 113 dB
USB Input to Analog Output: 113 dB

Connections

(2) XLR / 1/4" (6.35 mm) TRS inputs (Mic 1-2)
(2) RCA stereo input pairs (Deck 3-4)
(2) XLR outputs (Main)
(2) 1/4" outputs (Booth)
(1) RCA stereo output pair (Main)
(1) 1/4" (6.35 mm) TRS output (Headphones)
(1) 1/8" (3.5 mm) TRS output (Headphones)
(2) USB Type-B ports
(2) USB Type-B ports

Audio Outputs

Main Outputs (XLR):
Gain Trim: Off to 0 dB
Maximum Output: 8 Vrms
THD+N (20 kHz BW @ 1 kHz): 0.004%
Frequency Response: Flat - 20-20kHz

Main Outputs (RCA stereo pair):
Maximum Output: 4 Vrms
THD+N (20 kHz BW @ 1 kHz): 0.004%
Frequency Response: Flat - 20-20kHz

Booth Outputs (1/4"):
Gain Trim: Off to 0 dB
Maximum Output: 8 Vrms
THD+N (20 kHz BW @ 1 kHz): 0.004%
Frequency Response: Flat - 20-20kHz

Headphone Outputs (1/4"/6.35 mm and 1/8"/3.5 mm TRS):
Maximum Output: 4 Vrms Voltage: (no load)
Output Power: 50 mW (50 ohms)
Dynamic Range (A-weighted): 108 dB

Audio Inputs

Microphone 1/2 (Combo XLR/1/4" [6.35 mm] TRS):
Analog Gain: 25 dB
Maximum Input: 110 mV
Gain Trim: Off to +26 dB (unity at center)
Tone Control: 2-band

Line/Phono Inputs 3/4 (RCA stereo pairs, switchable):

Line: Line
Maximum Input: 4 Vrms
Gain Trim: Off to +12 dB
Tone Control: 3-band, full-cut to +10 dB
THD+N (20 kHz BW @ 1 kHz: 0.004%

Phono: RIAA
RIAA Curve: +/-0.25 dB
Gain (@ 1 kHz): 31.5 dB
Maximum Input (@ 1 kHz): 106 mV
Dynamic Range (A-weighted): 102 dB

Pads: (16) on/off multi-colour back-lit pads (8 per deck, 9 modes each
Wheel Displays: (2) 320 x 240 Colour LCD's
Pad & FX Displays: (9) 128 x 32 Monochrome OLED's
Faders: (1) MAG FOUR tension-adjustable crossfader with contour, (4) Standard channel faders

Power:
Connection: IEC
Voltage: 100-240 V, 50/60 Hz
Consumption: 20 W

Dimensions (width x depth x height):
Dimensions (width x depth x height): 30.8" x 15.9" x 4.2" / 782.32 x 403.8 x 106.6 mm
Weight: 18.25 lbs./8.27 kg

Notes: W-MAT Cork / Cork 100%

Diameter / Diameter - 295 mm
Thickness - 3mm

High-quality mat made of 100% natural, flexible, high-density cork without artificial compounds. Designed to obtain excellent stabilization and grip of the disc, free of vibrations and a clean sound without interference.

Winyl W-Mat can replace any standard mat thanks to its 3mm thickness, ideal for any turntable model without the need to adjust the vertical tracking angle (VTA) of the tonearm.

Winyl W-Mat cork has been extensively hand washed twice after manufacture to ensure the protection of your records and enhance the experience in your HiFi system.

Unlike other products, our skid records are not printed with branding, logos or stickers so they blend aesthetically seamlessly into your turntable.

Characteristics:
Composition: 100% high-density natural cork
7.25mm centre hole
Made in Spain

Notes: The Selektor Crossbody Light Bag x 40 approximately holds 40 Single 7" records.

Features protective padding on its front and back. Features anti-shock new intelligent protective padding. UV protected & water repellent poly fabric.

Aesthetics & Function. Unique functionality, style & comfort for carrying your records and everyday carry. Lightweight.

Notes: Reloop's next-generation interface is the go-to for connecting turntables and media players to Serato, offering three stereo inputs and three stereo outputs. Studio-quality 24-bit / 96 kHz conversion and built-in USB-A hub.

Supplier's Notes:
Back to the music

The Reloop Flux is a next-generation USB-C interface for using Serato DJ Pro with turntables, CDJs or other media players. The interface boasts superior audio qualities, a well-designed operating concept and a club-ready design. It can transform any conventional mixer into a professional digital vinyl system.

Maximum flexibility

Three stereo inputs provide DJs with maximum flexibility. Turntables, CDJs and similar can be used in any combination. The settings are adjusted using discreet DIP switches, which virtually eliminates any chance of accidental switching in the club. The interface includes three stereo outputs, including an AUX out that can be routed to Serato's internal sampler. Gold-plated, corrosion-resistant RCA jacks ensure high-quality audio transmission.

Full control

The Flux provides the best possible routing overview thanks to clearly visible signal flow LEDs for all inputs and outputs and a Thru status indicator. Connection status (hub, PD, DC) LED indicators on the top of the interface provide additional control options. The Direct Thru buttons on the top of the interface enable you to quickly and easily activate and disable Thru mode, which allows connected turntables and CDJs to be used conventionally. Navigation through the Serato software is no longer necessary.

Hub inside

The Flux includes a built-in 2-port USB-A hub for connecting MIDI controllers and other USB accessories. Aside from the expanded connection options, the hub reduces potential connection faults in a busy club environment by keeping the setup connected even without the laptop.

Studio quality - anytime, anywhere

The Flux offers studio quality in the club and wherever it's needed with 24-bit/96 kHz, high-quality digital/analogue converters and ultra-low latency. For this reason, it's a superior DVS interface which could also be used as an audio interface in the studio.

Always powered

The Flux is bus-powered by a computer, so there's minimal wiring required for audio and power cables. The DVS interface can also be powered by external power sources through the USB-C DC input, allowing turntables and CDJs to be used in Thru mode even without a computer connected. The Flux's second USB-C port provides Power Delivery support for other USB-C devices (max. 60 W), such as a MacBook.

Robust & roadworthy

The interface has a durable metal housing with a scratch-resistant, black surface, ensuring a long service life even with heavy use. The extended edge design keeps the connections well-protected.

Plug & play for Serato DJ

The Reloop Flux unlocks the full version of Serato DJ Pro and Serato DVS. This means DJs can get up and running with the market-leading digital vinyl system in no time. Additional licences are not necessary.

Features:

3-channel (6x6 in/out) USB-C DVS interface for Serato DJ Pro
Turn any mixer into a professional digital vinyl system
Unlocks full version of Serato DJ Pro and Serato DVS
Studio-grade 24-bit sound card with crystal-clear audio and ultra-low latency response
Supports up to 96kHz with high-quality D/A converters for superior audio processing
Also functions as a stand-alone studio interface for recording and playback audio
3x inputs for turntables, CD players or AUX-In for live feed signal, switchable in any combination via dedicated dip switches
Dedicated GND terminal for grounding turntables
Gold-plated, corrosion-resistant audio connections
3x line outputs, including AUX-Out, assignable to the Sampler
Easy, accessible direct thru buttons for analogue deck playback
All terminals are visible from the top of the unit for easy installation in dark surroundings
Bus-powered cable connection for power and audio
Optional USB-C DC in port for external power supply
Power delivery support for USB-C devices (max 60W)
Signal-flow LEDs for all inputs and outputs (L/R) and thru indication for clear visibility
Power LEDs on the top panel for connection status (Hub, PD, DC)
2-port USB-A hub for connecting further accessories
Rugged, heavy-duty metal housing with a scratch-resistant black finish for durability on the road and reliability in the club
Highly robust, extended edge design to protect connection terminals
Supports the use of Serato NoiseMap™ control vinyl (not included) or custom control signal WAV file for use via CDs or USB drive (download available) with no additional license purchase needed
Including: 2x RCA audio cables, 1x USB-A to USB-C, 1x USB-C to USB-C, user manual

Technical Data

Power:
USB bus powered: Yes
Recommended power: 2 A or higher / minimum power: 400 mA
Maximum USB-PD throughput: 60 W
Maximum USB Hub power output: 2 x 0.8 A = 8 W
Supported external USB (type A or C) power supply: 5 V/1 A - 20 V/3 A
Power supply priority: FLUX self-power -> USB Hub -> PD (to PC)

Audio:
S/N Ratio (output reference level 1 kHz, +4 dB):
- Deck In (LINE signal input: 0 dBV): More than 83 dB
- Deck In (PHONO signal input: -32 dBV): More than 73 dB
THD + N:
-LINE signal input: -4 dBV @1K / Less than 0.03% (1 kHz,+0 dB)
-PHONO signal input: -36 dBV @1K / Less than 0.05% (1 kHz,+0 dB, Inverse RIAA)
Maximum Gain:
- Deck In (LINE): +4 dB i 2 dB
- Deck In (PHONO): +36 dB i 2 dB
Maximum Input (1 kHz, THD=1%):
- Deck In (LINE): More than +7 dBV
- Deck In (PHONO): More than -25 dBV
Maximum Output (1 kHz, THD=1%):
- Deck Output: More than +11 dBV

USB:
USB audio interface with 24 bit/44.1 kHz, 48 kHz, 96 kHz
USB 2.0 high-speed (480 Mbit/s)
Class-compliant on macOS
USB Power Delivery Protocol 3.0

General:
Dimensions (W x D x H): 160 x 120 x 34 mm
Weight: 0.85 kg
Accessories: User Manual, 1x USB type C/C cable, 1x USB type C/A cable, 2x RCA cable bit

Notes: Pack of 3 Extra-large lint free microfibre cloths are the perfect choice to clean your vinyl. Use to rest your LP on while cleaning to keep the underside of your LP protected. The super soft microfibre is lint free so is also perfect to clean the delicate surface of your LPs. Won't scratch or leave residual particles so you can be sure of a gentle but thorough clean.

Notes: Fits over 12" LP Record jacket. Will hold double album jacket.

12" Record Jacket Sleeve. No flap.

12-3/4 x 12-3/4".

2 mil Polyethylene.

Notes: LP Record Cardboard Jacket

Black

12-1/4 x 12-1/4"

With centre hole on both sides.

Notes: LP Record Cardboard Jacket

20 Pt. Kraft Chipboard

12-1/4 x 12-1/4"

With centre hole on both sides.

Notes: The ultra-fine goat hair carefully remove dust and dirt from your records. The soft, antistatic bristles reduce the build-up of static electricity and give you a crisp, clean sound. Can be used with AM record cleaner for a deeper cleaning. The handle is made of Japanese Zelkova wood.

Clean sound since 1971

Drain the static charge from your records and lift any residual dust and grime. The conductivity of the brush's ultra-fine goat hairs eliminates static charges while gently and efficiently removing the dust, grit and particles that bung up your vinyl's grooves and degrade your record's sound. The hair reach deep into the grooves of your vinyl to remove even the smallest particles, leaving your records clean while prolonging the life of vinyl and stylus.

How it works

Gently hold the the brush in the grooves as the record spins. After the record makes a full rotation, angle the brush towards the outside of the record and carefully sweep the particles from the vinyl surface.

Notes: UDG have further fined-tuned what was already a great design concept of a flight case into one especially for the most discerning DJ/ producer. This is constructed from aluminium, thus providing an extremely stable structure with lighter weight compared to traditional flight cases.

The UDG Ultimate Record Cases are designed to keep your vinyl protected from accidental damage when you transport it to and from gigs. They're compact and lightweight yet tough enough to keep your valuable records safe.

Specification

Colour: Black
Weight: 2,50 kg / 5.5 lbs
Outer Dimensions (W x H x D): 44.0 x 24.0 x 27.0 cm | 17.3 x 9.4 x 10.6 inch
Inner Dimensions (W x H x D): 41.8 x 20.6 x 25.2 cm | 16.4 x 8.1 x 9.9 inch
Material: Aluminium
Protection: Corrosion resistant aluminium profiles with strong rounded corners
Fully lined with high density foam protective padding
Strong butterfly lock and solid metal hinges
Rubber feet at the bottom for support in standing position

Extras

Lighter weight than traditional flight cases
Black Diamond finishing surface
Ergonomic & sturdy carry handle
Fits: Approximately up to 200 7"/LP vinyl records. Capacity will depend on the thickness of the records & their packaging

Notes: A turntable without a StylusTimer is like a car without a Speedo!
Turntable phono cartridges have a stylus that should be replaced after every 1000 hours of use, sometimes even sooner, depending on the cartridge. A worn stylus degrades sound quality and can damage your valuable record collection. Unfortunately, most turntable owners have no idea how much time is actually on their stylus, especially as the months and years go by. Now you can track stylus usage easily and precisely with StylusTimer, a unique chronograph designed for use with turntables.

Tonar Stylus Timer
Protect your records
Track Listening Time
Determine when to replace your Stylus
Know precisely how many hours are on your stylus or cartridge
Track break-in hours and changes in sound quality over time
Protect your record collection from damage by a worn stylus
Know when it is time to replace your stylus or cartridge
Maximise your investment, especually with high-end cartridges
Have fun watching the hours climb, tracking your listening habits

Notes: This is the same high-end inner sleeve design that comes with some of the best audiophile record pressings and labels, but at a reasonable price. It's an archival quality, three-ply, soft rice paper sleeve that is anti-static and acid-free. These sleeves will keep your collection dust and scratch free. After you've given your records a bath with GrooveWasher record cleaning fluids, it's only natural to dry them off and put them in some clean undies!

50 Sleeves Per Pack
Audiophile Standard Design
Three-Ply, Anti-Static, Rice Paper, Acid-Free, Premium Record Inner Sleeves
Keep Your Collection Clean and Dust Free
Dimensions: 12 1/8" x 12 1/8"

Notes: There are many options when it comes to outer sleeves these days. These are the everyday workhorse of outer sleeves that will protect your album jackets at a reasonable price. 12.75" x 12.75", 3 Mil, polyethylene that will cover both single and double LP gatefold jackets. If you're looking for outer sleeves to get the job done simply and cost effectively- you're here!

100 Sleeves Per Pack
Premium Quality 3 Mil. Thickness Polyethylene
Dimensions: 12.75" x 12.5" with Flush Cut Opening to fit both single LP and double LP gatefold jackets

Notes: Keep your vinyl collection in pristine condition with this specially designed antistatic brush. Designed to clear the fine grooves of dust & fluff without damaging the delicate playing surfaces, an essential requirement for maintaining optimum reproduction quality.